TESTO 606-2 Bedienungsanleitung

Andere Handbücher für 606-2

2

Inhaltsverzeichnis

Andere TESTO Messgerät Handbücher

TESTO

TESTO 230 Bedienungsanleitung

TESTO

TESTO 606-2 Bedienungsanleitung

TESTO

TESTO Saveris Bedienungsanleitung

TESTO

TESTO 605-H1 Bedienungsanleitung

TESTO

TESTO 0636.9835 Benutzerhandbuch

TESTO

TESTO 350 Maritime V2 Anleitung zur Verwendung

TESTO

TESTO 545 Bedienungsanleitung

TESTO

TESTO 460 Bedienungsanleitung

TESTO

TESTO 460 Handbuch

TESTO

TESTO 605-H1 Bedienungsanleitung

TESTO

TESTO 300 Handbuch

TESTO

TESTO Smart Probes 115i Bedienungsanleitung

TESTO

TESTO 300 LL Bedienungsanleitung

TESTO

TESTO 535 Bedienungsanleitung

TESTO

TESTO 510 Bedienungsanleitung

TESTO

TESTO 0600 9765 Bedienungsanleitung

TESTO

TESTO 417 Bedienungsanleitung

TESTO

TESTO 545 Bedienungsanleitung

TESTO

TESTO 340 Bedienungsanleitung

TESTO

TESTO 623 Bedienungsanleitung

TESTO

TESTO DiSCmini Bedienungsanleitung

TESTO

TESTO 350 Maritime V2 Bedienungsanleitung

TESTO

TESTO 445 Bedienungsanleitung

TESTO

TESTO 515 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Instruction manual

testo 606-2

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Short manual testo 606-2 11

Short manual testo 606-2

Protection cap: Park position

Sensing electrodes

Humidity/temperature sensor

Display

Control keys

Battery compartment (on rear)

Test resistance contact

List of settable materials, for

sticking into the protective cap

Basic settings

Instrument off >press and hold 2s > select with ( ),

confirm with ( ):

Unit of temperature: °C, °F > Unit of humidity: %, td (dew point), WB (wet bulb) >

Auto off function: OFF, ON

Switching the instrument on

Press .

Switching the display light on (for 10s)

Instrument on > press

Select display mode

Instrument on > select with :

Current reading > Hold: Readings are held > Max: Maximum values > Min: Minimum

values

Switching the instrument off:

Instrument on >press and hold 2s.

deenfresitptsvnl????

Safety and the enviroment12

Safety and the environment

About this document

> Please read this documentation through carefully and

familiarise yourself with the product before putting it to use.

Keep this document to hand so that you can refer to it when

necessary. Hand this documentation on to any subsequent

users of the product.

> Pay particular attention to information emphasised by the

following symbols:

With the signal word Caution!:

Warns against hazards which could result in minor physical injury

or damage to equipment if the precautionary measures indicated

are not taken.

Important.

Avoid personal injury/damage to equipment

> Only operate the measuring instrument properly, for its

intended purpose and within the parameters specified in the

technical data. Do not use force.

> Never store the product together with solvents, acids or other

aggressive substances.

> Only carry out the maintenance and repair work that is

described in the documentation. Follow the prescribed steps

when doing so. Use only OEM spare parts from Testo.

Protecting the environment

> Take faulty rechargeable batteries as well as spent batteries to

the collection points provided for them.

> Send the product back to Testo at the end of its useful life. We

will ensure that it is disposed of in an environmentally friendly

manner.

Specification 13

Specifications

Functions and use

The testo 606-2 is a material moisture, air humidity and tempe-

rature measuring instrument. It is normally used to determine

the material moisture contents in wood or building materials

and air humidity. The measurement procedure used is suitable

for overview measurement to determine whenther the material

is continuing to dry out. The material moisture is given in % by

weight.

Technical data

deenfresitptsvnl????

Measurement data

· Sensors:

Electrical resistance (conductivity

measurement), Testo humidity sensor,

NTC temperature sensor

· Parameters:

% by weight material moisture (wood,

building materials), %rH, td, wb, °C, °F

· Measuring ranges:

-10...50 °C, 14...122 °F, 0...100 %rH

Material moisture: See chapter Using

the Product

· Resolutions:

0.1 %, 0.1 °C, 0.1 °F, 0.1 %rH

· Accuracies (Nominal temperature

25 °C, ±1 Digit):

Conductivity measurement ±1 %,

±0.5 °C, ±0.9 °F,

±2.5%rH (5...95%rH)

· Measuring rate:

0.5 s, humidity: 1s

Further instrument data

· Protection class: IP20

· Ambient conditions:

-10...50 °C, 14...122 °F

· Storage/transport conditions:

-40...70 °C, -40...158 °F

· Voltage supply:

2x 1.5 V type AAA

· Battery life:

130 h (without display light)

· Dimensions:

119x46x25mm / 4.69x1.81x0.98” (inc.

protection cap)

· Weight: 90 g / 3.2 oz (inc. batteries and

protection cap)

Examinations and licenses

· As declared in the Certificate of

Conformity, this product complies with

Directive 2004/108/EC.

Warranty

· Duration: 2 years

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com

Product description14

Product description

At a glance

Protection cap: Park position

Sensing electrodes

Caution! Risk of injury

from sensing electrodes!

>Attach protection cap

when not in use.

Humidity/temperature sensor

Display

Control keys

Battery compartment (on rear)

Test resistance contact

List of settable materials, for

sticking into the protective cap

First steps

Inserting batteries:

1To open the battery compartment, push the battery cover

down.

2Insert batteries (2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

Basic settings (configuration mode):

Adjustable functions

· Unit of temperature: °C, °F

· Unit of humidity: %, td (dew point), WB (wet bulb)

· Auto off function: OFF, ON (instrument switches off automatically if no key is

pressed for 10 minutes)

1When switching the instrument on, press and hold until

and appear on the display (configuration mode).

- The adjustable function is displayed. The current setting

flashes.

Using the product 15

2Press ( ) several times until the desired setting flashes.

3Press ( ) to confirm the input.

4Repeat steps 2and 3for all functions.

- The instrument changes to measuring mode.

Using the product

To guarantee correct readings:

· Repeat the measurement at several points. The differing

resistance of the wood, with or across the grain, may have

an impact on the measurement result. If the injection needles

are inserted with the grain, this may result in slightly higher

readings because the resistance in the material is lower.

· A measurement is only implemented as far as the depth that

the injection needles are inserted within the material. Insert

the measuring needles as far as possible (4 to 5 mm).

· When measuring fuel moisture content, it is advisable to split

the log prior to measurement and to measure at three points.

Measuring points: each 5 cm away from the left and right cut

edge and once in the centre of the log.

· Keep temperature and humidity sources which may falsify the

measurement (e.g. hands) away from the sensor.

The values displayed are highly dependent on the building

material/manufacturer used, and on the ambient conditions .

As the materials are natural, the same materials can vary from

batch to batch.

Switching the instrument on:

> Press .

- Measuring mode is opened.

Switching the display light on:

The instrument is switched on.

> Press .

- The display light goes out automatically if no key is

pressed for 10 seconds.

Setting the material characteristic curve:

The material moisture is indicated in the top line of the

display. The material symbol (wood) or (building

deenfresitptsvnl????

Using the product16

material) is displayed with the relevant material number (see

enclosed sticker for the inside of the protective cap).

Settable materials Measuring range

1. beech, spruce, larch, birch, cherry, walnut 8.8...54.8 % by weight

2. oak, pine, maple, ash-tree, douglas fir, meranti 7.0...47.9 % by weight

3. cement screed, concrete 0.9...22.1 % by weight

4. anhydrite screed 0.0...11.0 % by weight

5. cement mortar 0.7...8.6 % by weight

6. lime mortar, plaster 0.6...9.9 % by weight

7. bricks 0.1...16.5 % by weight

> Press several times until the desired material

characteristic curve appears.

Testing the instrument function:

1Press several times until Test: lights up.

2 Connect sensing electrodes with the contacts of the test

resistor on the top of the protection cap.

- Test flashes.

- Test: ok lights up: instrument is functioning.

Test: ok does not light up: test not possible, see chapter

‚Tips and assistance‘.

3Press back to measurement menu.

Changing the display view:

Adjustable views

· Current reading

· Hold: Readings are held.

Max/Min-display for air humidity and temperature only.

· Max: Maximum values since the instrument was last switched on or last reset.

· Min: Minimum values since the instrument was last switched on or last reset.

> Press several times until the desired view appears.

Resetting Max/Min values:

1Press several times until the desired view appears.

2Press and hold until - - - - appears.

3Repeat steps 1and 2for all values that are to be reset.

Switching the instrument off:

> Press and hold until the display goes out.

Maintaining the product 17

Maintaining the product

Changing batteries:

1To open the battery compartment, push the battery cover

down.

2Remove used batteries and insert new batteries

(2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

Cleaning the housing:

> Clean the housing with a moist cloth (soap suds) if it is dirty.

Do not use aggressive cleaning agents or solvents!

Questions and answers

Question Possible causes/solutions

Hi or Lo · Readings outside the measuring range (too high,

too low): Readings outside the measuring range

(too high, too low): for materials that have not been

specially dried or moistened, the measurement

results should always be within the measuring range.

·

Residual capacity <10 min: Change batteries.

Testing the instrument

function: Test: ok does

not light up · Clean sensing electrodes and contacts on the top

of the protection cap.

· If the error message appears again, send the

instrument to Testo Customer Service.

Meas. electrodes defective/

worn · Send instrument to Testo customer service.

The material‘s measured moisture content is relative to the dry

weight (0% moisture) of the relevant material. The stored material

characteristic curves were determined using the Darr (wet and dry

weighing) method. The specified measuring ranges are derived

from this.

Conversion to percent by weight

Percent by weight = (wet weight-dry weight) × 100 / dry weight

Example

Wet weight: 180 g

Dry weight: 150 g

Percent by weight: (180 - 150) × 100 / 150 = 20%

deenfresitptsvnl????

Tips and assistance

18

Conversion to water content

Water content % = (wet weight-dry weight) / dry weight × 100

Example

Wet weight: 180 g

Dry weight: 150 g

Percent by weight: (180 - 150) / 150 × 100 = 16.6%

What constitutes dry, or at risk, or damp?

The values indicated serve as guideline figures for assessing the

materials. The values are typical inner area values

Characteristic curve Material Dry At risk Damp /

very damp

Characteristic curve 1

or 2 inside heated

Beech, fir, larch... < 12 12...15 > 15

Characteristic curve 1

or 2 inside unheated

Oak, pine, maple

wood...

< 15 15...20 > 20

Characteristic curve 3 Cement screed < 3 3...5 > 5

Characteristic curve 3 Concrete < 2.2 2.2...4.4 > 4.4

Characteristic curve 4 Anhydrite screed < 0.5 0.5...1 > 1

Characteristic curve 5 Cement mortar < 3 3...5 > 5

Characteristic curve 6 Lime mortar < 2 2...4 > 4

Characteristic curve 6 Gypsum < 2 2...4 > 4

Characteristic curve 7 Brick < 1 1...3 > 3

Guideline values for the installation moisture of wood, which sets

in as an average after a certain period in use-status (DIN 1052-1

(4/88) Para. 4.2.1.):

Char. curve Application area Wood humidity in % by weight

1 or 2 buildings closed on all sides with heating 9 ± 3

1 or 2 buildings closed on all sides without heating 12 ± 3

1 or 2 roofed open buildings 15 ± 3

1 or 2 constructions which are open to the weather on all sides 18 ± 6

If we could not answer your question, please contact your dealer

or Testo Customer Service.

0973 6062 de en fr es it pt ru 05

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com