Texas Instruments PMP15034 Bedienungsanleitung
Test Report
July 2017
1
PMP15034 Test Results
System Description
A piezoelectric sounder is a loudspeaker that uses the piezoelectric effect to generate sound. It is widely used in
the application where sound volume and high pitch are more important than sound quality, such as toys, air
conditioner, microwave oven and alarm equipment.
The piezoelectric sounder normally required a 1-KHz to 5-KHz rectangular voltage to operate. The sound press
mainly depends on the amplitude of the driving voltage. The higher driving voltage, the higher sound press will be.
For example, the PKM13EPYH4002 from Murata requires 0-V to 30-V or +15-V to −15-V rectangular voltage. The
power supply in these applications could be two cell alkaline battery, lithium-ion battery or 3.3-V, 5-V power rail,
which is much lower than the target voltage. Therefore, a high performance, simple boost converter TLV61046A
is required for this application.
TLV61046A is 1.8-V - 5.5-V input, up to 28-V output, full integrated boost converter. It integrates low side
MOSFET, high side rectifier diode and the isolation MOSFET. The isolation MOSFET disconnects the pass-
through path between input and output when the device is disabled. This function helps to reduce the battery
power loss when the piezoelectric sounder doesn’t work.
Based on TLV61046A, the reference design introduces two driving circuit of piezoelectric sounder. With PWM
signal from MCU, one circuit provides rectangular wave driving voltage between 0-V and 28-V; the other circuit
provides ±15-V rectangular wave driving voltage.
The block diagram of the 28-V driver circuit is shown in Figure 1. The output voltage of the TLV61046A is set to
28V. A PWM signal from MCU drives Q1 to control the voltage across the piezoelectric sounder LS. When PWM
signal is logic high, the Q1 turns on, so 28V is applied to LS. When PWM signal is logic low and Q1 turns off, the
LS is discharged by the resistor in parallel. The frequency of the PWM signal should be equal to the
recommended frequency of the sounder. The duty of the PWM should be as low as possible to reduce the power
loss when the sound press is acceptable.
1.8V~5.5V
TLV61046A
Boost Converter
VIN
GND
VOUT
PWM
28V
GND
U1
Q1
LS
Figure 1: Block Diagram of the 28-V Driver Circuit
The block diagram of ±15-V driving circuit is shown in Figure 2. The output of the TLV61046A is set to 15V. An
additional charge pump circuit doubles the output voltage to approximately 30V. When Q1 turn off and Q2 turn on,
the voltage according the sounder LS is 15V; when Q1 turns on and Q1 turns off, the voltage according LS is -
15V. The frequency of driving voltage follows the PWM input from MCU. By modifying the feedback divider of the
TLV61046A and selecting proper Q1, Q2, this circuit supports ±28 V for the sound. The resistor in parallel with LS
can discharge the voltage to zero after the boost converter is disabled.
Lit. Number
2PMP15034 Test Results
1.8V~5.5V
TLV61046A
Boost Converter
VIN
GND
VOUT
PWM
15V
GND
U2
Q2
LS
Charge Pump
SW
30V Q1
+-
Figure 2: Block Diagram of ±15-V Driver Circuit
Design Theory
The schematic of the 28-V driver circuit is shown in Figure 3. The output voltage of the boost converter is
configured by R1 and R3. This voltage should be set to as high as possible to get highest sound.
Q1 is a NPN device driven by the PWM signal from the MCU. The sounder TS1 is charged to 28V when Q1 turns
on, and discharged by the R2 to 0V when Q1 turns off. The frequency of the PWM should be equal to the
recommended operating frequency of the sounder, which is 4KHz in this reference design.
The duty cycle of the PWM and the R2 resistance impact the sound press of TS1. They also impact the power
loss of the driver circuit because the current flows through R2 to ground when Q1 turns on.
The power loss of R2 is calculated by equation (1), where D is duty cycle of the input PWM signal.
PR2 = VOUT2 × D ÷ R2 (1)
Follows are two steps to find suitable R2 and duty cycle to compromise the sound press and power loss:
Setting the duty cycle to 50%, select a 1-KΩ to 10-KΩ resistor that minimize the power loss without
suffering the sound press
Using R2 selected by step 1, slowly decrease the duty cycle to minimize the power loss if the sound press
requirement is met.
Figure 3: 28-V Rectangular Waveform Driver Circuit
Lit. Number
PMP15034 Test Results 3
The schematic of the ±15-V driver circuit is shown in Figure 4. the output voltage of the TLV61046A is set to 15V.
The additional charge pump circuit doubles the output voltage to approximately 30V. The NPN Q2 and PNP Q3
form a totem pole driver circuit. The Q4 and R5 form a simple level shift circuit. When PWM is high voltage, the
Q4 turns on. So the totem pole circuit outputs 0.7V. The voltage according LS2 is -14.3V. When the PWM is low
voltage, the output voltage of totem pole circuit is 29.3V. So the LS2 voltage is 14.3V.
Figure 4: ±15-V Rectangular Waveform Driver Circuit
The current flowing through R5 to ground increases the power loss of the circuit. It is suggested to minimize the
duty cycle of the PWM signal if the sound press meets the requirement.
The R6 in parallel with LS2 discharge the DC voltage at LS2 to zero after the TLV61046A is disabled.
Test Result
Figure 5 shows the startup waveform the 28-V circuit by EN signal. The device finishes startup process in 7ms. It
is suggested that the PWM input signal is 7ms later than EN high logic.
VOUT 5V/div
EN 2V/div
Figure 5: Startup at VIN=3.3V
Figure 6 shows operating waveform when the PWM input signal is 4KH with 30% duty and VIN = 3.3V. The
sounder voltage is charged to 28V when the Q1 turns on, and discharged to almost 0 V by the resistor when the
Q1 turns off
Lit. Number
4PMP15034 Test Results
Driving Voltage 10V/div
PWM 5V/div
Figure 6: Operating Waveform with 4-KHz PWM
The startup by EN waveform of the ±15-V circuit is shown in Figure 7, the two output voltage ramps up to target
value within 7ms.
VOUT 5V/div
EN 2V/div
Double VOUT 10V/div
Figure 7: Startup at VIN=3.3V
Figure 8 shows the operating waveform with 4-KHz, 30% duty PWM input when VIN=3.3V. The rising and falling
time is very short because the totem pole has strong driving capability.
Driving Voltage 10V/div
PWM 5V/div
Figure 8: Operating Waveform with 4-KHz PWM
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
Inhaltsverzeichnis
Andere Texas Instruments Computerhardware Handbücher
Texas Instruments
Texas Instruments LDC3114-Q1 Bedienungsanleitung
Texas Instruments
Texas Instruments BQ28Z610-R2 Produkthandbuch
Texas Instruments
Texas Instruments LM60EVM Bedienungsanleitung
Texas Instruments
Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung
Texas Instruments
Texas Instruments Jacinto 7 DRA829 Bedienungsanleitung
Texas Instruments
Texas Instruments ADS130E08EVM-PD Bedienungsanleitung
Texas Instruments
Texas Instruments TUSB9260 Bedienungsanleitung
Texas Instruments
Texas Instruments OMAP36 Series Produkthandbuch
Texas Instruments
Texas Instruments AM335 Series Leitfaden
Texas Instruments
Texas Instruments ADS41 Series Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320C642x DSP Bedienungsanleitung
Texas Instruments
Texas Instruments TUSB2E11 Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320C2 Series Bedienungsanleitung
Texas Instruments
Texas Instruments eZ430-TMS37157 Bedienungsanleitung
Texas Instruments
Texas Instruments SimpleLink CC3200 Wi-Fi Bedienungsanleitung
Texas Instruments
Texas Instruments TPA6135A2 EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TSC2007EVM Bedienungsanleitung
Texas Instruments
Texas Instruments PHP1250 Bedienungsanleitung
Texas Instruments
Texas Instruments controlCARD TMDSCNCD2800137 Bedienungsanleitung
Texas Instruments
Texas Instruments LM38020QEVM Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
