Texas Instruments CC1110 Programmierhandbuch

SWRU135A

October 2008

Address information

Low Power RF web site: http://www.ti.com/lprf

Low Power RF community: http://www.ti.com/lprf-forum

TI Worldwide Support: http://support.ti.com

Technical Support Email: [email protected]

Make sure to subscribe to the Low-Power

RF Newsletter to receive information about

updates to documentation, new product

releases and more. Sign up on our web site!

CC1110-CC1111DK Quick Start Instructions

RF/Packet Error Rate Test

1. Kit Contents

•2 SmartRF04EB

•2 CC1110EM 433 MHz

•2 CC1110EM 868-915 MHz

•1 CC1111 USB dongle 868-915 MHz

•1 SOC_DEM

•2 antennas (433 MHz)

•2 antennas (868/915 MHz)

•2 USB cables

•1 USB extension cable

•1 10-pin cable

2. EB overview

3. Plug EM into EB

Insert a CC1110EM into both SmartRF04EBs.

The connectors will only fit in one position, so

that the EM cannot be inserted the wrong way.

Do not force the EM. Remember to mount the

antenna as well. The frequency range of the

selected EM decides which antenna to use.

NB! Different antennas for different frequencies:

433MHz

868/915MHz

4a. Battery power

There are three different ways of applying power

to the EB:

The first method involves using a battery, either a

9V or a 4xAA battery pack connected to the

battery connector on the bottom side of the board

4b. DC power

The second method applies DC power using the

DC input jack (right in picture, centre is +, sleeve is

ground), or by connecting a 4-10V voltage source

between the 4-10V and 0V terminals of the power

connector (left in picture). It is also possible to

connect a 3.3V voltage source between the 3.3V

and 0V terminals. The on-board voltage regulators

will be bypassed in this case.

4c. USB power

The EB can also be powered from the USB bus.

Make sure that the SmartRF®Studio software is

installed before connecting the EB to the PC,

otherwise you may experience problems in

installing it later due to driver issues.

Note that if multiple power sources are

connected, the source with the highest voltage

will power the EB. This means that you should

disconnect any attached battery when using a

lab supply or USB power, otherwise the battery

will be drained.

5. Set power switch

If a 3.3V source is used as described in 4b

above, the switch should be set to the leftmost

position. For all other cases, the switch should be

set to the rightmost position. This switch can be

used to turn off the EB by switching it to the

opposite position of that used to turn it on.

6. Packet error rate test

When power is applied to the board, the test

program will start. You should see the Chipcon

logo with chip name and revision number as shown

above on the LCD display on both EBs. Pushing

button S1 in the lower right corner of the board will

show the first menu item.

7. Select Frequency

Select a frequency according to the type of EM

module in use (433 MHz, 868 MHz, 903 MHz or

915 MHz). Move the joystick up or down to

display the choices and push button S1 in the

lower right corner of the board to select the

displayed frequency.

LCD screen

connectors

Button S1

Joystick

SWRU135A

October 2008

Address information

Low Power RF web site: http://www.ti.com/lprf

Low Power RF community: http://www.ti.com/lprf-forum

TI Worldwide Support: http://support.ti.com

Technical Support Email: [email protected]

Make sure to subscribe to the Low-Power

RF Newsletter to receive information about

updates to documentation, new product

releases and more. Sign up on our web site!

5. Select Data Rate

Select which data rate to use (1.2 kbps, 38.4

kbps or 250 kbps) by moving the joystick.

Confirm your choice by pushing button S1.

6. EB 1: Select Receiver

Select Receiver on the first EB by moving the

joystick. Confirm by pressing button S1. The

Receiving node will display “Ready to receive”.

7. EB 2: Select Transmitter

Select Transmitter on the other EB by moving the

joystick upward. Confirm by pressing button S1.

8. EB 2: Number of packets

On the transmitter EB, select the number of

packets to send. More packets take longer, but

give a better statistical result. Confirm by

pressing button S1.

9. PER Test (Transmitter)

Press S1 button again to start transmitting the

packet burst. The transmitter will show a running

counter that shows the number of packets sent.

10. PER Test (Receiver)

The receiver will show the total accumulated

packet error rate (PER) together with the average

signal strength (RSSI) of the previous 32 received

packets. A symbol in the upper right corner will

blink for every 32nd incoming packet to indicate

whether the link is maintained.

11. PER Test results

When the PER test is completed, the result will

be displayed on the receiver until a new test is

started. A new test can be started from the

transmitter.

12. Documentation

Please visit www.ti.com to download the

CC1110-CC1111DK User Manual, the

SmartRF® Studio software, examples, as well

as relevant datasheets and application notes.

If you for some reason cannot access the TI

web site and download the files, please contact

your local TI representative for assistance.

1. Troubleshooting/Notice

It you are experiencing problems with this test,

please check the following:

•Please visit www.ti.com and enter

CC1110-CC1111DK in the part number

search box. Check for updated SW and

documentation. Updated SW can be

downloaded to the device using IAR or the

Flash Programmer application.

•If you get poor PER results at short

distances, try to move the transmitter and

receiver further apart. The CC1110 may

experience saturation when transmitting at

full output power if the units are too close.

•The source code for the packet error rate

application is available on the web. You

may modify the source code to test at

other frequencies or data rates.

•See “DN300 -- SmartRF04EB

Troubleshooting” for general

troubleshooting of your EB board.

SmartRF®Studio

1. Download

Before connecting the EB to your PC, download

SmartRF®Studio from www.ti.com/smartrfstudio.

The installer is located in the “Support Software”

section. Download and run the installer.

2. Plug in EB

After the install program finishes, connect the EB

to the PC using the USB cable. Run SmartRF®

Studio. Select the SmartRF®04 tab. Select the

CC1110 board at the top of the list, and click the

Start button.

3. Configure

You can now configure the radio chip, run tests

or communicate with another EB.

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless

Andere Handbücher für CC1110

Dieses Handbuch passt für folgende Modelle

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F67461 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F28376D Bedienungsanleitung

Texas Instruments

Texas Instruments LaunchPad C2000 F280015 Series Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Programmierhandbuch

Texas Instruments

Texas Instruments MSP430 series Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6730 Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon Products CC1050DK Bedienungsanleitung

Texas Instruments

Texas Instruments SimpleLink CC2620 Produkthandbuch

Texas Instruments

Texas Instruments TMDXRM42HDK Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320C6000 DSP Leitfaden

Texas Instruments

Texas Instruments MSP430F22x4 Series Bedienungsanleitung

Texas Instruments

Texas Instruments CC2531 Installationshandbuch

Texas Instruments

Texas Instruments MSP430G2744DA Bedienungsanleitung

Texas Instruments

Texas Instruments RM46L852 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1298RECG-FE Bedienungsanleitung

Texas Instruments

Texas Instruments CC2652RSIP Bedienungsanleitung

Texas Instruments

Texas Instruments LaunchPad LP-CC1352P7-1 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320C67 DSP Series Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments Arrow IoT Bedienungsanleitung

Texas Instruments

Texas Instruments CC1110 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung