Texas Instruments DRV8251/AEVM Bedienungsanleitung

User’s Guide

DRV8251/AEVM User's Guide

ABSTRACT

This document is provided with the DRV82X1 family customer evaluation modules (EVM) as a supplement to

the DRV8251, DRV8251A, DRV8231 and DRV8231A data sheets. This user's guide describes the hardware

implementation of the EVM.

Hot surface. Contact may cause burns. Do not exceed limitations of the DRV devices:

4.5-V to 48-V operating supply voltage range • RDS(on), voltage, and current sense/regulation

variants (external shunt resistor and integrated current mirror) – DRV8251: 4.5-V to 48-V, 450-mΩ,

shunt – DRV8251A: 4.5-V to 48-V, 450-mΩ, mirror – DRV8231: 4.5-V to 33-V, 600-mΩ, shunt –

DRV8231A: 4.5-V to 33-V, 600-mΩ, mirror • Keep the peak current below 1.6 A RMS to avoid

temperatures above 130°C (at 25°C ambient temperature).

Table of Contents

1 PCB (Top and Assembly View).............................................................................................................................................. 2

2 Introduction.............................................................................................................................................................................3

3 Power Connectors and Coding............................................................................................................................................. 3

3.1 Programming EVM.............................................................................................................................................................3

4 Component Description......................................................................................................................................................... 5

5 Operation of the EVM............................................................................................................................................................. 6

5.1 H-Bridge Control................................................................................................................................................................ 7

5.2 Current Sensing and Current Regulation Details............................................................................................................... 7

6 Removing and Installing Supported Motor Drivers.............................................................................................................9

7 Revision History......................................................................................................................................................................9

Trademarks

eZ-FET™ is a trademark of Texas Instruments.

All trademarks are the property of their respective owners.

www.ti.com Table of Contents

SLVUC78 – NOVEMBER 2021

Submit Document Feedback

DRV8251/AEVM User's Guide 1

1 PCB (Top and Assembly View)

Figure 1-1. PCB Assembly View

Figure 1-2. PCB Top 3-D View

PCB (Top and Assembly View) www.ti.com

2DRV8251/AEVM User's Guide SLVUC78 – NOVEMBER 2021

Submit Document Feedback

2 Introduction

The MD039 is a complete solution for evaluating the DRV8251/DRV8251A/DRV231/DRV8231A H bridge motor

drivers. It includes the necessary shunt resistors for the current regulation in the non a variants and the internal

FETs needed for the current mirroring circuit in the A variants.

The EVM includes and MSP430 microcontroller that is preprogrammed tot ake input from three dedicated

analog potentiometers for PWM (POT1) (POT2) speedcontrol as well as VREF (POT3) for current regulation and

monitoring. The jumper for STALL_ACT allows for the selection of differetn stall detection features depending on

the desired application.

The supply voltage can be externally powered to 48 V for the DRV8251x series and up to 33 V for

the DRV8231X series. To expand beyond the included firmware capability, the MSP430 MCU can be

reprogrammed through the eZ-FET™ emulation circuit found in most MSP430 Launchpads. We recommend

the MSP-EXP430FR5969. Note that a four pin angled male header is required and must be soldered to J21

of this Launchpad from V+ pin to GND pin. We recommend a pin header with pin dimensions similar to

850-10-050-20-001000 (Digikey part number). The U1 MCU must be removed from the Launchpad.

3 Power Connectors and Coding

The DRV8251/AEVM uses a single header for power entry to the EVM board. Only a single power supply rail

is necessary since an onboard 3.3-V regulator provides power to the MSP430. The minimum recommended VM

voltage for the EVM is 4.5 V and the maximum depends on the specific device installed (see reference section).

For complete voltage range information of the driver itself, refer to the device.

As previously mentioned, the MSP430 comes preprogrammed to control basic DC motor operation. If changing

the firmware via the external eZ-FET™ emulation tool, do not supply power to the VM connector on the EVM.

The eZ-FET™ board provides the necessary power during programming when connected to the J6 connector.

Note that a four-pin angled male header is required and must be soldered to J21 of this Launchpad from V+ pin

to GND pin shown in image below. We recommend a pin header with pin dimensions similar to the Digikey part

number 850-10-050-20-001000. The U1 MCU must be removed from the Launchpad.

3.1 Programming EVM

This section outlines the procedure for programming the EVM with a custom firmware. Out of the box, the

DRV8251/DRV8251A EVMs will come programmed so no programming is required from the user. However, the

information in this section only applies if the user wants to flash a custom program to the MSP430FR2100 MCU.

If you are interested in viewing the source firmware files, go to the tool product page and download the firmware

files.

To flash a custom firmware you will need the following components:

1. Code Composer Studio (CCS)

2. DRV8251/DRV8251AEVM

3. MSP430FR5969 LaunchPad

4. Mini USB to USB cable

Follow these steps in order to flash a custom firmware to the EVM MCU

1. Open Code Composer Studio. If you are new to CCS, visit this link to view the user's manual. Alternative,

you can visit dev.ti.com/tirex to view code examples for any of the TI MCUs.

2. Connect the power supply cables to the EVM, connect USB cable to the LaunchPad (LP) and the computer,

connect the launch pad to the EVM via the J21 connector on the LP and J6 on the EVM, make sure that

there are jumpers on "TST", "RST", "V+", and "GND" on J13 on the LP. Your set-up should look as the

picture below:

www.ti.com Introduction

SLVUC78 – NOVEMBER 2021

Submit Document Feedback

DRV8251/AEVM User's Guide 3

Figure 3-1. MSP-EXP430FR5969 connected to EVM

3. Once the code is ready to be flashed to the MCU, click on the "Debug" icon on the top left of the window.

Figure 3-2. CCS Debug Icon

4. If there are no compiling or linking issues, a "Play" button will appear on the top left window. Click on it to

run the program. If you get any errors in the code or any other error messages, please submit a post on

e2e.ti.com for assistance.

5. Congrats! Your EVM is now programmed with your custom code. You may now disconnect the EVM from the

LP.

Power Connectors and Coding www.ti.com

4DRV8251/AEVM User's Guide SLVUC78 – NOVEMBER 2021

Submit Document Feedback

4 Component Description

Figure 4-1. Render With Components Labelled

Table 4-1. Component Reference

Connector/Component Function

J1 Main poer supply connector

J3 Motor connection

J4 Signal header test points

J6 Header for launchpad connection

VREF Potentiometer for VREF Adjustment

3.3 V 3.3-V LDO Test point

IN1 PWM Potentiometer for VREF Adjustment

GND Main ground

Explanation of Components:

1. Pot1 controls the PWM signal that goes into IN1, by turning it clockwise you increase the duty cycle from 0%

to 100%.

2. Pot 2 controls the PWM signal that goes into IN2, by turning it clockwise you increase the duty cycle from

0% to 100%.

3. The potentiometer labelled VREF controls the setting for VREF. When turning it clockwise it increases

gradually until it reaches its limit adjusting VREF for 3.3 V

a. VREF is responsible for current regulation threshold, by lowering the value in VREF turning it

counterclockwise you will lower the current regulation threshold.

4. IN1 and IN2 test points will display the PWM signals coming from the microcontroller. Be sure to refer to the

stickers in the board to correctly identify IN1 and IN2 test points.

5. Vsense/Ipropi test point provides a voltage that is dependent on the current going through the load for

current regulation.

a. Said curent, and current regulation can be calculated by the equations in the current sensing and current

regulation section.

www.ti.com Component Description

SLVUC78 – NOVEMBER 2021

Submit Document Feedback

DRV8251/AEVM User's Guide 5

5 Operation of the EVM

Quickstart guide

1. Move POT1, POT2, and VREF all the way counter-clockwise

2. Connect power supply to connector J1. J1 is positive terminal and GND negative terminal as shown in

Figure 5-1.

Figure 5-1. Power Connected

3. Set power supply to desired voltage dependent on load, do not exceed the maximum limits of the device see

section above for max limits, for 8231 series it is 33 V

4. Enable power supply

5. The status LED D1 (Bottom left green led) will turn on

6. Disable power and connect load in J3 as shown in Figure 5-2:

Figure 5-2. Power and Load Connected

7. Re-enable power

8. Turn VREF potentiometer all the way clockwise.

a. This will make Itrip the maximum value possible.

Operation of the EVM www.ti.com

6DRV8251/AEVM User's Guide SLVUC78 – NOVEMBER 2021

Submit Document Feedback

9. Turn “POT1” (labeled as “IN1_PWM” on silkscreen) clock-wise. The motor should start spinning and its

speed should increase as the POT is turn more clockwise.

10. Slowly turn VREF counter clockwise while probing the VREF test point, this should allow you to set VREF to

the desired value for current regulation. If not current regulation is desired then leave VREF fully clockwise.

11. Turn “IN1_PWM” POT all the way counter-clockwise. Motor should come to a complete stop.

12. Turn “IN2_PWM” POT clock-wise. Motor should begin to spin the opposite direction of step 9

5.1 H-Bridge Control

Table 5-1. H-Bridge Control

IN1 IN2 OUT1 OUT2 DESCRIPTION

0 0 High-Z High-Z Coast; H-bridge disabled to High-Z (sleep entered after 1 ms)

0 1 L H Reverse (current OUT2 → OUT1)

1 0 H L Forward (current OUT1 → OUT2)

1 1 L L Brake; low-side slow decay

The inputs can be set to static voltages for 100% duty-cycle drive, or they can be pulse-width modulated (PWM)

for variable motor speed. When using PWM, switching between driving and braking typically works best. For

example, to drive a motor forward with 50% of its max RPM, IN1 = 1 and IN2 = 0 during the driving period, and

IN1 = 1 and IN2 = 1 during the other period. Alternatively, the coast mode (IN1 = 0, IN2 = 0) for fast current

decay is also available. The input pins can be powered before VM is applied.

FORWARD REVERSE

OUT1 OUT2

Forward drive

Slow decay (brake)

OUT1 OUT2

Reverse drive

Slow decay (brake)

3High-Z (coast) 3High-Z (coast)

Figure 5-3. H-Bridge Current Paths

5.2 Current Sensing and Current Regulation Details

The current sensing and current regulation will depend on the device used:

DRV8251AEVM and DRV8231AEVM:

An internal current mirror architetcture on the IPROPI pin implements current sensing and regulation. This

eliminates the need for a large power shunt resistor, saving board area and reducing system cost. The

IPROPI current-sense output allows a microcontroller to detect motor stall or changes in load conditions.

VREF determines the threshold of current regulation during start-up and stall events without interaction of a

microcontroller.

www.ti.com Operation of the EVM

SLVUC78 – NOVEMBER 2021

Submit Document Feedback

DRV8251/AEVM User's Guide 7

The motor current can be monitor by the IPROPI pin voltage. The IPROPI voltage is the voltage proportional to

the motor current. A more detailed explanation on how current regulation and sensing can be found on section

8.4.3 of the datasheet.

DRV8251EVM and DRV8231EVM:

Features integrated current regulation. This is implemented by comparing the analog input VREF and the

voltage on the ISEN pin, which is proportional to motor current through an external sense resistor. The ability

to limit current to a known level can significantly reduce the system power requirements and bulk capacitance

needed to maintain stable voltage, especially for motor startup and stall conditions.

Current regulation for both variants will be dependent on Itrip, a set threshold which once exceeded will cause

the device to enter current regulation. This threshold can be adjusted by the VREF potentiometer and follows the

following equations:

Figure 5-4. Current Regulation Equations

For more information be sure to refer to the datasheet of the device installed on the EVM.

Operation of the EVM www.ti.com

8DRV8251/AEVM User's Guide SLVUC78 – NOVEMBER 2021

Submit Document Feedback

6 Removing and Installing Supported Motor Drivers

The EVM can support the DRV8251/DRV8251A/DRV8231/DRV8231A devices. Below are step-by-step

instructions on how to remove and place different drivers on the EVM:

1. Disconnect power from the EVM.

2. Carefully de-solder the device from the PCB. Make sure to follow proper soldering and ESD protection

procedures to prevent damage to the EVM.

3. Carefully solder the new device to the EVM. Visit ti.com or any authorized third party vendor to purchase the

desired driver.

4. The EVM uses a combination of resistors to identify the device that is populated on the board.

5. The firmware will function slightly different depending on the device that is on the board. After installing the

new device, make sure to populate the appropriate resistors.

The Table 6-1 shows the changes that need to be implemented when switching from one device to the other.

Table 6-1. Procedure For Soldering New Device and Passives to EVM

New device being installed Soldering procedures

8251 switching to 8251A • Solder the device to footprint U2. Make sure pin 1 of device aligns with the dot on the

PCB

• Depopulate C6, R5, R7, R8, R13, R14 and U2

• Populate R4 and R7 with 0 ohm resistor.

• Populate R5 with 1.5 kOhm resistor

8251A switching to 8251 • Solder the device to footprint U2. Make sure pin 1 of device aligns with the dot on the

PCB

• Depopulate R4, R5, and R7

• Populate R5 and R14 with 0 ohm resistor

• Populate R7 with 0.15 ohm resistor

• Populate C6 with 0.1 uF cap

• Populate R8 with 1k ohm resistor

• Populate R13 with 4.02 k ohm resistor

• Populate U4 with TLV9001IDCKRBe mindful of warnings in voltage differences.

This hardware can be used to test and validate the 8231 series as it is pin to pin compatible with the DRV8251

series. The steps of switching between DRV8231 and DRV8231A are identical as those between the DRV8251

to 8251A and vice versa.Be mindful of warnings in voltage differences.

7 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

DATE REVISION NOTES

November 2021 * Initial Release

www.ti.com Removing and Installing Supported Motor Drivers

SLVUC78 – NOVEMBER 2021

Submit Document Feedback

DRV8251/AEVM User's Guide 9

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, regulatory or other requirements.

These resources are subject to change without notice. TI grants you permission to use these resources only for development of an

application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license

is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you

will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these

resources.

TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with

such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for

TI products.

TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Inhaltsverzeichnis

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments AM571 Series Bedienungsanleitung

Texas Instruments

Texas Instruments CC110 Series Leitfaden

Texas Instruments

Texas Instruments MSPM0G150 Series Bedienungsanleitung

Texas Instruments

Texas Instruments ADC12DJ3200CVAL Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F67671 Bedienungsanleitung

Texas Instruments

Texas Instruments RM48 series Produkthandbuch

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2652RSIP Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320DM357 Bedienungsanleitung

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

Texas Instruments

Texas Instruments Delfino TMS320F28377D controlCARD Technisches Handbuch

Texas Instruments

Texas Instruments RM46 Bedienungsanleitung

Texas Instruments

Texas Instruments eZ430-Chronos Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon Products CC2400DK Bedienungsanleitung

Texas Instruments

Texas Instruments TMS570LC4357 Produkthandbuch

Texas Instruments

Texas Instruments MSP432P401R Bedienungsanleitung

Texas Instruments

Texas Instruments CC3235MODASF Bedienungsanleitung

Texas Instruments

Texas Instruments LaunchPad MSP430FR5994 Bedienungsanleitung

Texas Instruments

Texas Instruments DLP Discovery 4100 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6778 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6724 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP-EXP430G2ET Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung