Texas Instruments MSP430F42 series Bedienungsanleitung

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

DLow Supply-Voltage Range, 1.8 V to 3.6 V

DUltralow-Power Consumption:

− Active Mode: 400 μA at 1 MHz, 3.0 V

− Standby Mode: 1.6 μA

− Off Mode (RAM Retention): 0.1 μA

DFive Power-Saving Modes

DWake-Up From Standby Mode in Less

Than 6 μs

DFrequency-Locked Loop, FLL+

D16-Bit RISC Architecture, 125-ns

Instruction Cycle Time

DThree Independent 16-bit Sigma-Delta A/D

Converters With Differential PGA Inputs

D16-Bit Timer_A With Three

Capture/Compare Registers

DIntegrated LCD Driver for 128 Segments

DSerial Communication Interface (USART),

Asynchronous UART or Synchronous SPI

Selectable by Software

DBrownout Detector

DSupply Voltage Supervisor/Monitor With

Programmable Level Detection

DSerial Onboard Programming,

No External Programming Voltage Needed

Programmable Code Protection by Security

Fuse

DBootstrap Loader in Flash Devices

DFamily Members Include:

− MSP430F423:

8KB + 256B Flash Memory,

256B RAM

− MSP430F425:

16KB + 256B Flash Memory,

512B RAM

− MSP430F427:

32KB + 256B Flash Memory,

1KB RAM

DAvailable in 64-Pin Quad Flat Pack (QFP)

DFor Complete Module Descriptions, Refer

to the MSP430x4xx Family User’s Guide,

Literature Number SLAU056

description

The Texas Instruments MSP430 family of ultralow power microcontrollers consist of several devices featuring

different sets of peripherals targeted for various applications. The architecture, combined with five low power

modes, is optimized to achieve extended battery life in portable measurement applications. The device features

a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code

efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less

than 6 μs.

The MSP430F42x series are microcontroller configurations with three independent 16-bit sigma-delta A/D

converters, each with an integrated differential programmable gain amplifier input stage. Also included is a

built-in 16-bit timer, 128 LCD segment drive capability, hardware multiplier, and 14 I/O pins.

Typical applications include high resolution applications such as handheld metering equipment, weigh scales,

and energy meters.

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range

from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage

because very small parametric changes could cause the device not to meet its published specifications. These devices have limited

built-in ESD protection.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

2POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

AVAILABLE OPTIONS

PACKAGED DEVICES

TAPLASTIC 64-PIN QFP

(PM)

−40°C to 85°C

MSP430F423IPM

MSP430F425IPM

MSP430F427IPM

pin designation{

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P1.5/TACLK/ACLK/S28

P2.3/SVSIN

P2.4/UTXD0

P2.5/URXD0

RST/NMI

TCK

TMS

TDI/TCLK

TDO/TDI

P1.0/TA0

P1.1/TA0/MCLK

P1.2/TA1/S31

P1.3/SVSOUT/S3

P1.4/S29

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

P1.6/SIMO0/S27

P1.7/SOMI0/S26

P2.0/TA2/S25

P2.1/UCLK0/S24

R33

R23

R13

R03

COM3

COM2

COM1

COM0

S23

S21

S22

A0.0+

A0.0−

A1.0+

A1.0−

A2.0+

A2.0−

XIN

XOUT

P2.2/STE0

MSP430F42x

VREF

AVCC

DVCC

AVSS

DVSS

†Open connection recommended for all unused analog inputs.

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

functional block diagram

SD16

Three 16-bit

Sigma-Delta

A/D

Converters

DVCC DVSS AVCC AVSS

RST/NMI

Flash

32KB

16KB

8KB

RAM

1KB

512B

256B

Watchdog

WDT+

15/16-Bit

Timer_A3

3 CC Reg

Port 1

8 I/O

Interrupt

Capability

POR/

SVS/

Brownout

Basic

Timer 1

1 Interrupt

Vector

LCD

128

Segments

1,2,3,4 MUX

fLCD

USART0

UART or

SPI

Function

Oscillators

FLL+

MCLK

8 MHz

CPU

incl. 16

Registers

XOUT

JTAG

Interface

XIN

SMCLK

ACLK

MDB

MAB

Emulation

Port 2

6 I/O

Interrupt

Capability

Module Hardware

Multiplier

MPY, MPYS

MAC,MACS

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

4POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

MSP430F42x Terminal Functions

TERMINAL

PN I/O DESCRIPTION

NAME NO.

I/O

DESCRIPTION

DVCC 1Digital supply voltage, positive terminal.

A0.0+ 2 I Internal connection to SD16 Channel 0, input 0 +. (see Note 1)

A0.0− 3 I Internal connection to SD16 Channel 0, input 0 −. (see Note 1)

A1.0+ 4 I Internal connection to SD16 Channel 1, input 0 +. (see Note 1)

A1.0− 5 I Internal connection to SD16 Channel 1, input 0 −. (see Note 1)

A2.0+ 6 I Internal connection to SD16 Channel 2, input 0 +. (see Note 1)

A2.0− 7 I Internal connection to SD16 Channel 2, input 0 −. (see Note 1)

XIN 8 I Input port for crystal oscillator XT1. Standard or watch crystals can be connected.

XOUT 9 O Output terminal of crystal oscillator XT1

VREF 10 I/O Input for an external reference voltage / internal reference voltage output (can be used as mid-voltage)

P2.2/STE0 11 I/O General-purpose digital I/O / slave transmit enable—USART0/SPI mode

S0 12 O LCD segment output 0

S1 13 O LCD segment output 1

S2 14 O LCD segment output 2

S3 15 O LCD segment output 3

S4 16 O LCD segment output 4

S5 17 O LCD segment output 5

S6 18 O LCD segment output 6

S7 19 O LCD segment output 7

S8 20 O LCD segment output 8

S9 21 O LCD segment output 9

S10 22 O LCD segment output 10

S11 23 O LCD segment output 11

S12 24 O LCD segment output 12

S13 25 O LCD segment output 13

S14 26 O LCD segment output 14

S15 27 O LCD segment output 15

S16 28 O LCD segment output 16

S17 29 O LCD segment output 17

S18 30 O LCD segment output 18

S19 31 O LCD segment output 19

S20 32 O LCD segment output 20

S21 33 O LCD segment output 21

S22 34 O LCD segment output 22

S23 35 O LCD segment output 23

COM0 36 O Common output, COM0−3 are used for LCD backplanes.

COM1 37 O Common output, COM0−3 are used for LCD backplanes.

COM2 38 O Common output, COM0−3 are used for LCD backplanes.

COM3 39 O Common output, COM0−3 are used for LCD backplanes.

R03 40 I Input port of fourth positive (lowest) analog LCD level (V5)

NOTE 1: Open connection recommended for all unused analog inputs.

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

MSP430F42x Terminal Functions (Continued)

TERMINAL

PN I/O DESCRIPTION

NAME NO.

R13 41 I Input port of third most positive analog LCD level (V4 or V3)

R23 42 I Input port of second most positive analog LCD level (V2)

R33 43 O Output port of most positive analog LCD level (V1)

P2.1/UCLK0/S24 44 I/O General-purpose digital I/O / external clock input-USART0/UART or SPI mode, clock output—USART0/SPI

mode / LCD segment output 24 (See Note 1)

P2.0/TA2/S25 45 I/O General-purpose digital I/O / Timer_A Capture: CCI2A input, Compare: Out2 output / LCD segment output

25 (See Note 1)

P1.7/SOMI0/S26 46 I/O General-purpose digital I/O / slave out/master in of USART0/SPI mode / LCD segment output 26

(See Note 1)

P1.6/SIMO0/S27 47 I/O General-purpose digital I/O / slave in/master out of USART0/SPI mode / LCD segment output 27

(See Note 1)

P1.5/TACLK/

ACLK/S28 48 I/O General-purpose digital I/O / Timer_A and SD16 clock signal TACLK input / ACLK output (divided by 1,

2, 4, or 8) / LCD segment output 28 (See Note 1)

P1.4/S29 49 I/O General-purpose digital I/O / LCD segment output 29 (See Note 1)

P1.3/SVSOUT/

S30 50 I/O General-purpose digital I/O / SVS: output of SVS comparator / LCD segment output 30 (See Note 1)

P1.2/TA1/S31 51 I/O General-purpose digital I/O / Timer_A, Capture: CCI1A, CCI1B input, Compare: Out1 output / LCD segment

output 31 (See Note 1)

P1.1/TA0/MCLK 52 I/O General-purpose digital I/O / Timer_A, Capture: CCI0B input / MCLK output.

Note: TA0 is only an input on this pin / BSL receive

P1.0/TA0 53 I/O General-purpose digital I/O / Timer_A, Capture: CCI0A input, Compare: Out0 output / BSL transmit

TDO/TDI 54 I/O Test data output port. TDO/TDI data output or programming data input terminal.

TDI/TCLK 55 I Test data input or test clock input. The device protection fuse is connected to TDI.

TMS 56 I Test mode select. TMS is used as an input port for device programming and test.

TCK 57 I Test clock. TCK is the clock input port for device programming and test.

RST/NMI 58 I Reset input or nonmaskable interrupt input port

P2.5/URXD0 59 I/O General-purpose digital I/O / receive data in—USART0/UART mode

P2.4/UTXD0 60 I/O General-purpose digital I/O / transmit data out—USART0/UART mode

P2.3/SVSIN 61 I/O General-purpose digital I/O / Analog input to brownout, supply voltage supervisor

AVSS 62 Analog supply voltage, negative terminal. Supplies SD16, SVS, brownout, oscillator, and LCD resistive

divider circuitry.

DVSS 63 Digital supply voltage, negative terminal

AVCC 64 Analog supply voltage, positive terminal. Supplies SD16, SVS, brownout, oscillator, and LCD resistive

divider circuitry; must not power up prior to DVCC.

NOTE 1: LCD function selected automatically when applicable LCD module control bits are set, not with PxSEL bits.

General-Purpose Register

Program Counter

Stack Pointer

Status Register

Constant Generator

General-Purpose Register

PC/R0

SP/R1

SR/CG1/R2

CG2/R3

R12

R13

General-Purpose Register

R10

R11

General-Purpose Register

R14

R15

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

6POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

short-form description

CPU

The MSP430 CPU has a 16-bit RISC architecture

that is highly transparent to the application. All

operations, other than program-flow instructions,

are performed as register operations in

conjunction with seven addressing modes for

source operand and four addressing modes for

destination operand.

The CPU is integrated with 16 registers that

provide reduced instruction execution time. The

one cycle of the CPU clock.

Four of the registers, R0 to R3, are dedicated as

program counter, stack pointer, status register,

and constant generator respectively. The

remaining registers are general-purpose

registers.

Peripherals are connected to the CPU using data,

address, and control buses, and can be handled

with all instructions.

instruction set

The instruction set consists of 51 instructions with

three formats and seven address modes. Each

instruction can operate on word and byte data.

Table 1 shows examples of the three types of

instruction formats; the address modes are listed

in Table 2.

Table 1. Instruction Word Formats

Dual operands, source-destination e.g. ADD R4,R5 R4 + R5 −−−> R5

Single operands, destination only e.g. CALL R8 PC −−>(TOS), R8−−> PC

Relative jump, un/conditional e.g. JNE Jump-on-equal bit = 0

Table 2. Address Mode Descriptions

ADDRESS MODE S D SYNTAX EXAMPLE OPERATION

Indexed D D MOV X(Rn),Y(Rm) MOV 2(R5),6(R6) M(2+R5)−−> M(6+R6)

Symbolic (PC relative) D D MOV EDE,TONI M(EDE) −−> M(TONI)

Absolute D D MOV &MEM,&TCDAT M(MEM) −−> M(TCDAT)

Indirect DMOV @Rn,Y(Rm) MOV @R10,Tab(R6) M(R10) −−> M(Tab+R6)

Indirect

autoincrement DMOV @Rn+,Rm MOV @R10+,R11 M(R10) −−> R11

R10 + 2−−> R10

Immediate DMOV #X,TONI MOV #45,TONI #45 −−> M(TONI)

NOTE: S = source D = destination

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

operating modes

The MSP430 has one active mode and five software-selectable low-power modes of operation. An interrupt

event can wake up the device from any of the five low-power modes, service the request, and restore back to

the low-power mode on return from the interrupt program.

The following six operating modes can be configured by software:

DActive mode (AM)

− All clocks are active

DLow-power mode 0 (LPM0)

− CPU is disabled

ACLK and SMCLK remain active, MCLK is available to modules

FLL+ loop control remains active

DLow-power mode 1 (LPM1)

− CPU is disabled

ACLK and SMCLK remain active, MCLK is available to modules

FLL+ loop control is disabled

DLow-power mode 2 (LPM2)

− CPU is disabled

MCLK, FLL+ loop control, and DCOCLK are disabled

DCO’s dc-generator remains enabled

ACLK remains active

DLow-power mode 3 (LPM3)

− CPU is disabled

MCLK, FLL+ loop control, and DCOCLK are disabled

DCO’s dc-generator is disabled

ACLK remains active

DLow-power mode 4 (LPM4)

− CPU is disabled

ACLK is disabled

MCLK, FLL+ loop control, and DCOCLK are disabled

DCO’s dc-generator is disabled

Crystal oscillator is stopped

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

8POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

interrupt vector addresses

The interrupt vectors and the power-up starting address are located in the address range of 0FFFFh−0FFE0h.

The vector contains the 16-bit address of the appropriate interrupt-handler instruction sequence.

INTERRUPT SOURCE INTERRUPT FLAG SYSTEM INTERRUPT WORD ADDRESS PRIORITY

Power-up

External Reset

Watchdog

Flash memory

PC Out-of-Range (see Note 4)

WDTIFG

KEYV

(see Note 1)

Reset 0FFFEh 15, highest

NMI

Oscillator Fault

Flash memory access violation

NMIIFG (see Notes 1 and 3)

OFIFG (see Notes 1 and 3)

ACCVIFG (see Notes 1 and 3)

(Non)maskable

0FFFCh 14

0FFFAh 13

SD16

SD16CCTLx SD16OVIFG,

SD16CCTLx SD16IFG

(see Notes 1 and 2)

Maskable 0FFF8h 12

0FFF6h 11

Watchdog Timer WDTIFG Maskable 0FFF4h 10

USART0 Receive URXIFG0 Maskable 0FFF2h 9

USART0 Transmit UTXIFG0 Maskable 0FFF0h 8

0FFEEh 7

Timer_A3 TACCR0 CCIFG (see Note 2) Maskable 0FFECh 6

Timer_A3

TACCR1 and TACCR2

CCIFGs, and TACTL TAIFG

(see Notes 1 and 2)

Maskable 0FFEAh 5

I/O port P1 (eight flags) P1IFG.0 to P1IFG.7

(see Notes 1 and 2) Maskable 0FFE8h 4

0FFE6h 3

0FFE4h 2

I/O port P2 (eight flags) P2IFG.0 to P2IFG.7

(see Notes 1 and 2) Maskable 0FFE2h 1

Basic Timer1 BTIFG Maskable 0FFE0h 0, lowest

NOTES: 1. Multiple source flags

2. Interrupt flags are located in the module.

3. (Non)maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt-enable cannot.

4. A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0h−01FFh) or from

within unused address ranges (from 0600h to 0BFFh).

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

special function registers

Most interrupt and module enable bits are collected into the lowest address space. Special function register bits

that are not allocated to a functional purpose are not physically present in the device. Simple software access

is provided with this arrangement.

interrupt enable 1 and 2

7654 0

UTXIE0 OFIE WDTIE

321

rw–0 rw–0 rw–0

Address

0h URXIE0 ACCVIE NMIIE

rw–0 rw–0 rw–0

WDTIE: Watchdog-timer interrupt enable. Inactive if watchdog mode is selected. Active if watchdog

timer is configured in interval timer mode.

OFIE: Oscillator-fault-interrupt enable

NMIIE: Nonmaskable-interrupt enable

ACCVIE: Flash access violation interrupt enable

URXIE0: USART0: UART and SPI receive-interrupt enable

UTXIE0: USART0: UART and SPI transmit-interrupt enable

7654 0321

Address

1h BTIE

rw-0

BTIE: Basic Timer1 interrupt enable

interrupt flag register 1 and 2

7654 0

UTXIFG0 OFIFG WDTIFG

321

rw–0 rw–1 rw–(0)

Address

02h URXIFG0 NMIIFG

rw–1 rw–0

WDTIFG: Set on watchdog timer overflow (in watchdog mode) or security key violation. Reset on VCC

power up or a reset condition at the RST/NMI pin in reset mode.

OFIFG: Flag set on oscillator fault

NMIIFG: Set via RST/NMI pin

URXIFG0: USART0: UART and SPI receive flag

UTXIFG0: USART0: UART and SPI transmit flag

7654 0321

Address

3h BTIFG

rw-0

BTIFG: Basic Timer1 interrupt flag

MSP430F42x

MIXED SIGNAL MICROCONTROLLER

SLAS421A − APRIL 2004 − REVISED JUNE 2007

10 POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

module enable registers 1 and 2

7654 0

UTXE0

321

rw–0 rw–0

Address

04h URXE0

USPIE0

URXE0: USART0: UART mode receive enable

UTXE0: USART0: UART mode transmit enable

USPIE0: USART0: SPI mode transmit and receive enable

7654 0321

Address

05h

Legend: rw−0,1: Bit Can Be Read and Written. It Is Reset or Set by PUC.

rw−(0,1): Bit Can Be Read and Written. It Is Reset or Set by POR.

SFR Bit Not Present in Device.

memory organization

MSP430F423 MSP430F425 MSP430F427

Memory

Interrupt vector

Code memory

Size

Flash

8KB

0FFFFh − 0FFE0h

0FFFFh − 0E000h

16KB

0FFFFh − 0FFE0h

0FFFFh − 0C000h

32KB

0FFFFh − 0FFE0h

0FFFFh − 08000h

Information memory Size 256 Byte

010FFh − 01000h

256 Byte

010FFh − 01000h

256 Byte

010FFh − 01000h

Boot memory Size 1kB

0FFFh − 0C00h

1kB

0FFFh − 0C00h

1kB

0FFFh − 0C00h

RAM Size 256 Byte

02FFh − 0200h

512 Byte

03FFh − 0200h

1KB

05FFh − 0200h

Peripherals 16-bit

8-bit

8-bit SFR

01FFh − 0100h

0FFh − 010h

0Fh − 00h

01FFh − 0100h

0FFh − 010h

0Fh − 00h

01FFh − 0100h

0FFh − 010h

0Fh − 00h

bootstrap loader (BSL)

The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial

interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete

description of the features of the BSL and its implementation, see the Application report Features of the MSP430

Bootstrap Loader, Literature Number SLAA089.

BSL Function PM Package Pins

Data Transmit 53 - P1.0

Data Receive 52 - P1.1

Inhaltsverzeichnis

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments AFE722 Series Bedienungsanleitung

Texas Instruments

Texas Instruments LP-EM-CC1354P10-1 Handbuch

Texas Instruments

Texas Instruments OMAP-L137/C6747 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2430ZDK Bedienungsanleitung

Texas Instruments

Texas Instruments TMS570LS Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F6768 Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Programmierhandbuch

Texas Instruments

Texas Instruments Vision SDK Linux Bedienungsanleitung

Texas Instruments

Texas Instruments LaunchPad MSP430FR2355 Bedienungsanleitung

Texas Instruments

Texas Instruments CC1125 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2530 ZigBee Development Kit Bedienungsanleitung

Texas Instruments

Texas Instruments bq24707EVM Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430FG6425 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430G2231 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320C67 DSP Series Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F22x4 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TMS570LC4357 Produkthandbuch

Texas Instruments

Texas Instruments Hercules RM57L Bedienungsanleitung

Texas Instruments

Texas Instruments CC2520EM Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F67781 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F67471 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments CC-6LOWPAN-DK-868 Bedienungsanleitung

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung