Texas Instruments SimpleLink CC2650 Bedienungsanleitung

SWRU402

January 2015

SimpleLink™CC2650 Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test

1. Kit Contents

2 x SmartRF06 Evaluation Boards (SRF06EB)

2 x CC2650 Evaluation Modules (CC2650EM)

2 x Micro USB Cables

Documentation

The RF boards in this kit are designed, but not

certified, to comply with FCC, IC and ETSI

requirements.

2. SmartRF06EB Overview

3. Plug the EM into the 06EB

Insert a CC2650EM board into the

SmartRF06EB as shown above.

Caution! The kit contains ESD sensitive

components. Handle with care to prevent

permanent damage.

4. Power Options

The CC2650EM should be powered through the

SmartRF06EB, which will supply a voltage from

2.1 V to 3.6 V to the daughter card. The

SmartRF06EB can be powered in several

different ways:

USB (5 V through USB plug)

2 x 1.5V AAA alkaline batteries (non rechrg.)

External regulated power supply

External Regulated Power SupplyRequirements1:

Nominal voltage: 2.1 to 3.3 VDC

Maximum voltage 3.6 VDC

Max Current: 1000 mA

Efficiency Level V

Warning! To minimize risk of injury or property

damage, never use rechargeable batteries to

power the board. Do not leave the EVM powered

when unattended.

5. Select Power Source

The power source is selected using the Source

switch on the left hand side of the SmartRF06EB.

In “USB” position, the EM is powered over USB,

running at 3.3V.

In “BAT” position, the board is powered from

batteries or an external source, running at 2.1V.

The 2.1V regulator can be bypassed by shorting the pins on

the “regulator bypass” jumper. In this case, the EM is

powered directly from the external source or batteries.

Note that there should only be one active

power source at any one time.

6. Welcome Screen

Turn on power with the Main Power switch. You

should now see the Texas Instruments logo and

a short description of the buttons on the LCD.

Pushing any of the five buttons on the board will

take you to the main menu.

NB! If you don’t see anything on the screen

make sure the board is correctly powered

(see step 4 and 5 above).

7. Select Board and Protocol

Start by selecting the plug-in board you have.

Then select the protocol.

In this guide, we will use BLE, but the settings

and operations that follow will be the same or

similar for IEEE 802.15.4.

8. Select Channel and Mode

Once you have selected the protocol, you should

select which frequency you want to operate at.

For BLE you can chose any of the three

advertising channels or the data channels.

Then select the type of test you want to run.

Packet mode is the Packet Error Rate test. CW is

a continuous wave signal, either modulated or

unmodulated.

When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and safety certification requirements such as

UL, CSA, VDE, CCC, and PSE

Buttons

Connectors

Micro SD

card reader

USB

Main

Power

Switch

Emulator

LEDs

LCD

LEDs

10-pin

ARM Debug

Connector

Breakout

Power

Selection

20-pin

ARM-JTAG

Connector

Web sites: www.ti.com/wirelessconnectivity

E2E Forum: e2e.ti.com/support/wireless_connectivity

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

9. Select Direction

For the packet error rate test, set one of the

boards up as the receiver (RX) and the other as

the transmitter (TX).

The receiver does not require any further set-up

and is now ready to receive packets.

10. Select Burst Size

Next, still on the transmitter side, select the

desired burst size, that is, the number of packets

to transmit.

Then select the packet rate (number of packets

to transmit per second).

11. Select Output Power

On the transmitter, select the desired output

power.

12. Start Sending Packets

The transmitter is now configured and in idle

state. Sending packets is started and stopped by

pressing the Select button.

13. PER Test Results

On the receiver, the statistics window will show

the error rate based on the number of lost or

erroneous packets divided by the total number of

packets that should have been received.

14. Next Steps

Please refer to your local TI FAE or contact

person to get more information about the

SimpleLink CC2650 device and other devices in

this new family of ultra-low power wireless

microcontrollers.

In particular, you will be able to start working with

software development on the BLE Stack and

other software solutions from TI.

We sincerely hope that you will enjoy working

with the CC2650 device.

15. Troubleshooting

It you are experiencing problems with this test,

please check the following:

Nothing is shown in the display! Make sure

the board is powered correctly (see steps 5

and 6 above).

Please visit the kit web page and check for

updated SW and documentation. Updated

SW can be downloaded to the device using

IAR Embedded Workbench for ARM or

SmartRF Flash Programmer.

SmartRF™Studio

1. Getting Started

SmartRF Studio can be used to test the radio

interface on the CC2650 via an XDS debugger

from TI. The SmartRF06EB has an onboard

XDS100v3 debugger and can serve this purpose.

Get an early adopter version of SmartRF Studio

from your local TI FAE or contact person.

Before connecting SmartRF06EB to your PC,

download and install SmartRF Studio from

www.ti.com/smartrfstudio.

2. Launch SmartRF Studio

After installing the tool, connect the EB to the PC

using the USB cable and start SmartRF Studio.

Select the “2.4 GHz” tab and click the refresh

("Find device") button in the lower right corner.

Studio will now find the connected SmartRF06EB.

Double click on the detected SmartRF06EB to

launch the CC2650 device control panel.

3. Test the Radio

You can now configure the radio, run

performance tests and run link tests with

another CC2650 device controlled either by

your own software or by SmartRF Studio.

Andere Handbücher für SimpleLink CC2650

Andere Texas Instruments Mikrocontroller Handbücher

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F4152IPM Bedienungsanleitung

Texas Instruments

Texas Instruments DEV-RF002 Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F28004 Series Bedienungsanleitung

Texas Instruments

Texas Instruments Vision SDK Linux Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1298RECG-FE Bedienungsanleitung

Texas Instruments

Texas Instruments Delfino TMS320F28377D controlCARD Technisches Handbuch

Texas Instruments

Texas Instruments Concerto F28M36 Series Produkthandbuch

Texas Instruments

Texas Instruments LaunchPad MSP430FR4133 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2520 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2533EMK Bedienungsanleitung

Texas Instruments

Texas Instruments CC2540DK-MINI Bedienungsanleitung

Texas Instruments

Texas Instruments DRV2605L Bedienungsanleitung

Texas Instruments

Texas Instruments SN65LVPE512 Bedienungsanleitung

Texas Instruments

Texas Instruments LaunchPad MSP-EXP430FR5994 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430F5638 Bedienungsanleitung

Texas Instruments

Texas Instruments bq2415 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TMS570LS31 HDK Bedienungsanleitung

Texas Instruments

Texas Instruments AM243 Series Bedienungsanleitung

Texas Instruments

Texas Instruments CC3220 Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430G2955 Bedienungsanleitung

Texas Instruments

Texas Instruments TMDXRM42HDK Bedienungsanleitung

Texas Instruments

Texas Instruments Hercules RM57L Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung

Mikroe

Mikroe click Proximity 2 Bedienungsanleitung