Texas Instruments TPS61054EVM-273 Bedienungsanleitung

User's GuideSLVU214 – June 2008

TPS61054EVM-273

This user’s guide describes the characteristics, operation, and use of the TPS61054EVM-273 evaluationmodule (EVM). This EVM demonstrates the Texas Instruments TPS61054 synchronousboost-converter-based high-power WLED driver. This document includes setup instructions, a schematicdiagram, a bill of materials, and PCB layout drawings for the evaluation module.

Contents1 Introduction ................................................................................................................... 22 Input/Output Connector Descriptions...................................................................................... 23 Test Results .................................................................................................................. 44 Board Layout ................................................................................................................. 75 Schematic and Bill of Materials ........................................................................................... 106 Related Documentation From Texas Instruments ..................................................................... 12

List of Figures

1 LED Efficiency vs Input Voltage – Torch Mode with ILED=75mA ..................................................... 42 LED Efficiency vs Input Voltage – Single-Pulse Flash Mode with ILED=700mA .................................... 53 Torch Flash Sequence ...................................................................................................... 54 Start-Up in Torch ............................................................................................................. 65 Voltage-Mode Efficiency .................................................................................................... 66 Voltage-Mode Load Transient .............................................................................................. 77 Assembly Layer .............................................................................................................. 88 Top Layer ..................................................................................................................... 89 Layer 2 ........................................................................................................................ 910 Layer 3 ....................................................................................................................... 911 Bottom Layer ................................................................................................................ 1012 TPS61054/5EVM-273 Schematic ........................................................................................ 11

List of Tables

1 Typical Performance Specification Summary ............................................................................ 22 Jumper Settings .............................................................................................................. 43 HPA273E-1 Bill of Materials .............................................................................................. 12

SLVU214 – June 2008 TPS61054EVM-273 1Submit Documentation Feedback

1 Introduction

1.1 Performance Specification Summary

1.2 Modifications

2 Input/Output Connector Descriptions

2.1 J1 – VIN

2.2 J2 – GND

2.3 J3 – FLASH / GND

Introduction

www.ti.com

The Texas Instruments TPS61054EVM-273 evaluation module uses the TPS61054 synchronous boostconverter-based high-power WLED driver. This WLED driver requires an input voltage between 2.5 V and6 V. The driver is configurable by on-board jumpers to either regulate output voltage or the output current.The goal of the EVM is to facilitate evaluation of the TPS61054 IC.

Table 1 provides a summary of the TPS61054EVM-273 performance specifications. All specifications aregiven for an ambient temperature of 25 °C.

Table 1. Typical Performance Specification Summary

VOLTAGE RANGE CURRENT RANGE(V) (mA)CONDITION

MIN TYP MAX MIN TYP MAX

2.5 6 2000supply

OUT

MODE0 = MODE1 = 1 4.85 5 5.15Torch current (MODE0 = 1 and MODE1 = 0 OR

(1)MODE0 = 0 and MODE1 = 1)I

LED

Flash current (MODE0 = 0 and MODE1 = 1 and

700

(2)FLASH_SYNC = 1)

(1)

±15% tolerance(2)

±12% tolerance

To aid user customization of the EVM, the board was designed with devices having 0603 or largerfootprints. A real implementation likely occupies less total board space.

Changing components can improve or degrade EVM performance. For example, adding a physicallylarger inductor with lower DCR improves efficiency.

This section describes the jumpers and connectors on the EVM as well as how properly to connect, setup, and use the TPS61054EVM-273.

This header is for the positive input supply voltage to the converter. The leads to the input supply shouldbe twisted and kept as short as possible to minimize EMI transmission and reduce inductive voltage droopat a load transient event.

This is the return connection for the input power supply of the converter.

This header connects to the FLASH_SYNC pin of the IC and to GND. It can be used to measure thevoltage on the FLASH_SYNC pin and/or apply an external signal to the FLASH_SYNC pin.

TPS61054EVM-273 2 SLVU214 – June 2008Submit Documentation Feedback

2.4 J4 – PULSE GEN / GND

2.5 J5 – TRANS RES

2.6 J6 – VOUT

2.7 J7 – LED

2.8 J8 – GND

2.9 JP1 – TX-TOFF

2.10 JP2 – MODE0

2.11 JP3 – MODE1

2.12 JP5 – OPEN LED

2.13 S1 – FLASH

www.ti.com

Input/Output Connector Descriptions

This header can be used to connect an external pulse generator to drive the gate of transistor Q1.Transistor Q1, along with components R2–R4, can be used to perform load transient testing and confirmstability.

This header connects to the drain of transistor Q1.

This header connects to the VOUT pin IC. In voltage-regulation mode, it can be used to measure theregulated output voltage and connect an external load resistance. In current-regulation mode, it connectsto the WLED cathode and can be used to measure the high-side WLED voltage.

This header connects to the LED pin of the IC. In current-regulation mode, it connects to the WLED anodeand can be used to measure the low-side WLED voltage. It is not used in voltage-regulation mode.

This header connects to the board ground plane and is the return for the VOUT header.

This jumper can be used to connect the TX-TOFF pin high (to the input voltage) or low (to ground).

This jumper can be used to connect the MODE0 pin high (to the input voltage) or low (to ground). See thedevice data sheet (SLUS760 ) for an explanation of configuration settings.

This jumper can be used to connect the MODE1 pin high (to the input voltage) or low (to ground). See thedevice data sheet (SLUS760 ) for an explanation of configuration settings.

This jumper is in series with power WLED D1. For the WLED to turn on, this jumper must be shorted.Placing an ammeter in series allows the user to measure current. The jumper in its default position isinstalled.

This push-button switch connects to the IC FLASH_SYNC pin and allows the user to initiate a WLED flashevent.

SLVU214 – June 2008 TPS61054EVM-273 3Submit Documentation Feedback

2.14 Hardware Setup

3 Test Results

VI− Input Voltage − V

100

2.5 3.0 3.5 4.0 4.5 5.0 5.5

LED Efficiency − %

G001

Test Results

www.ti.com

Table 2 shows the DEFAULT board jumper settings.

Table 2. Jumper Settings

JUMPER DEFAULT

JP1 LOJP2 LOJP3 LOJP4 SHORTED

Connect to J1 and J2 an input power supply rated at least 2-A and set to provide between 2.5 V and 6 V.The leads should be very short. Additional input capacitance on the C4 pads may be required in order tomitigate the inductive voltage droop that occurs at torch-current start-up and especially when the flashpulse occurs. Turn on the power supply.

WARNINGWARNING: This EVM has a white LED that flashes very brightly.Protective eye wear and/or a diffuser to cover the white LED duringoperation is recommended.

This section provides typical performance waveforms for the TPS61054/5EVM-273 board.

Figure 1. LED Efficiency vs Input Voltage – Torch Mode with ILED=75mA

4TPS61054EVM-273 SLVU214 – June 2008Submit Documentation Feedback

VI− Input Voltage − V

2.5 3.0 3.5 4.0 4.5 5.0 5.5

LED Efficiency (PLED/PIN) − %

G002

ILED = 700 mA

www.ti.com

Test Results

Figure 2. LED Efficiency vs Input Voltage – Single-Pulse Flash Mode with ILED=700mA

Figure 3. Torch Flash Sequence

SLVU214 – June 2008 TPS61054EVM-273 5Submit Documentation Feedback

100

IO− Output Current − mA

VI= 3.6 V

VO= 5 V

Efficiency − %

10 100 1k 10k

G003

Test Results

www.ti.com

Figure 4. Start-Up in Torch

Figure 5. Voltage-Mode Efficiency

6TPS61054EVM-273 SLVU214 – June 2008Submit Documentation Feedback

4 Board Layout

www.ti.com

Board Layout

Figure 6. Voltage-Mode Load Transient

This section provides the TPS61054EVM-273 board layout and illustrations.

Board layout is critical for all high-frequency, switch-mode power supplies. Figure 7 through Figure 11show the board layout for the TPS61054EVM-273 PCB. The nodes with high switching frequencies andcurrents are kept as short as possible to minimize trace inductance. Careful attention has been given tothe routing of high-frequency current loops, and a single-point grounding scheme is used. See the devicedata sheet (SLUS760 ) for specific layout guidelines.

SLVU214 – June 2008 TPS61054EVM-273 7Submit Documentation Feedback

K001

K002

Board Layout

www.ti.com

Figure 7. Assembly Layer

Figure 8. Top Layer

8TPS61054EVM-273 SLVU214 – June 2008Submit Documentation Feedback

K003

K004

www.ti.com

Board Layout

Figure 9. Layer 2

Figure 10. Layer 3

SLVU214 – June 2008 TPS61054EVM-273 9Submit Documentation Feedback

K005

5 Schematic and Bill of Materials

Schematic and Bill of Materials

www.ti.com

Figure 11. Bottom Layer

This section provides the TPS61054EVM-273 schematic and bill of materials.

10 TPS61054EVM-273 SLVU214 – June 2008Submit Documentation Feedback

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments UCC28221 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS25846-Q1 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8861EVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1202EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TMUX7208EVM Bedienungsanleitung

Texas Instruments

Texas Instruments UCC25230EVM-662 Bedienungsanleitung

Texas Instruments

Texas Instruments UCC25660 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS71401DRVEVM-426 Bedienungsanleitung

Texas Instruments

Texas Instruments THVD1424 Bedienungsanleitung

Texas Instruments

Texas Instruments bq77905 Bedienungsanleitung

Texas Instruments

Texas Instruments TAS5706EVM2 Bedienungsanleitung

Texas Instruments

Texas Instruments bq24072RGTR Bedienungsanleitung

Texas Instruments

Texas Instruments bqSWITCHER bq241 EVM Series Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430FR6043 Bedienungsanleitung

Texas Instruments

Texas Instruments TMUX741 EVM Series Bedienungsanleitung

Texas Instruments

Texas Instruments Chipset TRF2436EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DLP LightCrafter 4500 Bedienungsanleitung

Texas Instruments

Texas Instruments TSC2013EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65276V PMIC Bedienungsanleitung

Texas Instruments

Texas Instruments CAPTIVATE-FR2676 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS5400EVM-CVAL Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65217EVM Bedienungsanleitung

Texas Instruments

Texas Instruments bq20z70EVM-001 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8686SEVM-PDK Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung