Texas Instruments TPS61193EVM Bedienungsanleitung

Using the TPS61193EVM and TPS61193-Q1EVM

Evaluation Module

User's Guide

Literature Number: SNVU491

October 2015

Contents

1 Preface ............................................................................................................................... 4

1.1 About this Manual........................................................................................................ 4

1.2 Related Documentation from Texas Instruments .................................................................... 4

1.3 FCC Warning ............................................................................................................. 4

1.4 If You Need Assistance ................................................................................................. 4

2 Introduction......................................................................................................................... 4

3 Description of the TPS61193 or TPS61193-Q1 Device............................................................... 5

3.1 Features................................................................................................................... 5

3.2 Applications ............................................................................................................... 5

4 Hardware Setup ................................................................................................................... 6

5 Board Layout....................................................................................................................... 7

6 Start-Up of the EVM and Power Sequences............................................................................. 8

6.1 PWM Input to Initiate Start-up Sequence............................................................................. 8

6.2 Shutdown Sequence..................................................................................................... 8

7 Boost Converter................................................................................................................... 9

7.1 Switching Frequency .................................................................................................... 9

7.2 Spread Spectrum and Synchronization ............................................................................... 9

7.3 Voltage Control.......................................................................................................... 10

8 LED Current Sinks.............................................................................................................. 11

8.1 Output Configuration ................................................................................................... 11

8.2 Current Setting.......................................................................................................... 11

8.3 Brightness Control...................................................................................................... 11

9 Fault Detection................................................................................................................... 11

9.1 Fault Indicator........................................................................................................... 11

10 Evaluation Board Schematic................................................................................................ 12

11 Bill of Materials .................................................................................................................. 13

12 Appendix A: LED Load Board .............................................................................................. 14

2Table of Contents SNVU491–October 2015

Submit Documentation Feedback

www.ti.com

List of Figures

1 Evaluation Board Connectors and Setup................................................................................. 6

2 Top Layer .................................................................................................................... 7

3 Bottom Layer (GND)......................................................................................................... 7

4 Evaluation Board Stackup .................................................................................................. 8

5 Switching Frequency vs RFSET .............................................................................................. 9

6 Converter Maximum Output Voltage vs R12 ........................................................................... 10

7 Output Current vs RISET ................................................................................................... 11

8 Evaluation Board Schematic.............................................................................................. 12

9 LED Load Board - Top Side .............................................................................................. 14

10 LED Load Board - Bottom View.......................................................................................... 14

11 LED Load Board - Schematic Diagram.................................................................................. 15

12 Forward Voltage for Cree Xlamp ML-B LEDs ......................................................................... 16

All trademarks are the property of their respective owners.

SNVU491–October 2015 List of Figures

User's Guide

SNVU491–October 2015

TPS61193EVM Evaluation Module

1 Preface

1.1 About this Manual

This user’s guide describes the module used to evaluate characteristics, operation, and use of the

TPS61193 low EMI, high-performance 3-channel LED driver for automotive lighting. This document

includes a schematic diagram, PCB layout, and bill of materials (BOM).

1.2 Related Documentation from Texas Instruments

TPS61193 (SNVSAF4) and TPS61193-Q1 (SNVSAC7) data sheets

1.3 FCC Warning

This equipment is intended for use in a laboratory test environment only. It generates, uses, and can

radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable

protection against radio frequency interference. Operation of this equipment in other environments may

cause interference with radio communications, in which case the user, at their own expense, will be

required to take whatever measures may be required to correct this interference.

1.4 If You Need Assistance

Contact your local TI sales representative.

2 Introduction

The Texas Instruments TPS61193EVM evaluation module (EVM) helps designers to evaluate the

operation and performance of the TPS61193 or TPS61193-Q1 device. The TPS61193EVM uses the

TPS61193 or TPS61193-Q1 to drive up to 3 LED strings for LCD backlighting with high efficiency.

Information about output voltage and current ratings of the TPS61193 or TPS61193-Q1 can also be found

in the device data sheet.

A power supply connection for the VIN and test points for each signal can be found on the evaluation

board. A separate LED board can be used as a load; it is also possible to connect an LCD panel to the

output connectors.

For evaluation purposes, the EVM has been tested over a 4.5-V to 40-V input range. This voltage range is

within the recommended operating range for input voltage of the TPS61193 or TPS61193-Q1. Users are

cautioned to evaluate their specific operating conditions and choose components with the appropriate

voltage ratings before designing this circuitry into a final product.

4TPS61193EVM Evaluation Module SNVU491–October 2015

Submit Documentation Feedback

www.ti.com

Description of the TPS61193 or TPS61193-Q1 Device

3 Description of the TPS61193 or TPS61193-Q1 Device

The TPS61193 or TPS61193-Q1 is an automotive high-efficiency LED driver with integrated boost/SEPIC

converter. It has three high-precision current sinks that can be controlled by a PWM input signal.

The boost converter has adaptive output voltage control based on the LED current sink headroom

voltages. This feature minimizes the power consumption by adjusting the voltage to lowest sufficient level

in all conditions. A boost controller supports spread spectrum for switching frequency and an external

synchronization with dedicated pin. The high switching frequency allows the TPS61193 or TPS61193-Q1

to avoid disturbance for AM radio band.

The input voltage range for TPS61193 or TPS61193-Q1 is from 4.5 V to 40 V to support automotive

stop/start and load dump condition. The TPS61193 or TPS61193-Q1 device supports PWM brightness

dimming ratio up to 10 000:1 for an input PWM frequency of 200 Hz. The device integrates extensive

safety and protection features.

3.1 Features

• Three High-Precision Current Sinks

– Current Matching 1% (typical)

– Output Current up to 100 mA/Channel

– Dimming Ratio 10 000:1 at 200-Hz PWM input

• Integrated Boost/SEPIC for LED String Power

– Output Voltage up to 45 V

– Switching Frequency 300 kHz to 2.2 MHz

– Boost Synchronization Input

– Spread Spectrum

• Input Voltage Operating Range 4.5 V to 40 V

• Power-Line FET Control for Inrush Current Protection and Standby Energy Saving

• Extensive Safety and Fault Tolerance Features

– Fault Output

– Input Voltage OVP and UVLO

– Open and Shorted LED Fault Detection

– Thermal Shutdown

• Minimum Number of External Components

3.2 Applications

Automotive Infotainment, Instrument Cluster and Backlighting Systems

SNVU491–October 2015 TPS61193EVM Evaluation Module

INPUT

VOLTAGE

OUTPUT

CONFIGURATION

LED

CONNECTOR

CONTROL

POINTS

FAULT LED

CONTROL POINTS

SHUNTS

CONTROL

POINTS

CONTROL

POINTS

Hardware Setup

www.ti.com

4 Hardware Setup

Figure 1 shows connectors and main components on the TPS61193 or TPS61193-Q1 board.

Figure 1. Evaluation Board Connectors and Setup

6TPS61193EVM Evaluation Module SNVU491–October 2015

Submit Documentation Feedback

www.ti.com

Board Layout

5 Board Layout

Figure 2. Top Layer

Figure 3. Bottom Layer (GND)

See the TPS61193 (SNVSAF4) or TPS61193-Q1 datasheet (SNVSAC7) for PCB layout guidelines.

SNVU491–October 2015 TPS61193EVM Evaluation Module

Prepreg

Core

Prepreg

Top Layer

Bottom Layer

PGND

GND

Start-Up of the EVM and Power Sequences

www.ti.com

Figure 4. Evaluation Board Stackup

• 4-layer board FR4

• Material thickness 1.616 ± 10% mm

• Surface finish immersion gold

6 Start-Up of the EVM and Power Sequences

The TPS61193 or TPS61193-Q1 EVM is set up for easy start-up:

• Connect LEDs to OUT1 - OUT3 of connector J16. (Note: LED current default is 100 mA and maximum

boost voltage default is 37 V. LED outputs that are not used must be grounded via jumpers J11 to

J14.)

• Connect input (BATTERY) voltage 12 V to connector J25.

The LEDs turn on immediately because the jumpers on the EVM are set up for PWM input of 100% duty

cycle. For connector and jumper positions, see Figure 1 and Figure 8.

Input (BATTERY) voltage range is 4.5 V to 40 V.

The TPS61193 or TPS61193-Q1 has a dual function VDDIO/EN pin. By default, VDDIO/EN = 3.3 V is

generated automatically on the EVM from battery input voltage via jumpers J1 and J26. VDDIO/EN acts

as enable for the device as well as supply/reference voltage for IO logic. Device starts when VIN voltage is

present and above the VIN UVLO voltage level (4 V), and the VDDIO/EN voltage is set above threshold

voltage (1.2 V).

By default, boost switching frequency is 400 kHz (jumper J4 connecting R3 = 160 kΩto FSET) and boost

maximum voltage is 37 V (R12 = 750 kΩand R13 = 130 kΩ). See Section 7.1 and Section 7.3 for

description on how to change boost settings.

By default, LED current is 100 mA per string (jumper J5 connecting R4= 24 kΩto ISET). See Section 8.2

for the description on how to change LED current setting.

Alternatively to internal LDO, device circuitry can be powered from external power supply (4.4 V to 5.25 V)

connected to the LDO pin. Internal LDO is disabled in this case.

6.1 PWM Input to Initiate Start-up Sequence

The backlight is started by setting PWM input high. By default, the TPS61193EVM has PWM input set

high (100% duty cycle), which is connected to VDDIO through jumper J2. Alternatively, an external PWM

signal can be connected by removing jumper J2 , shorting pins 3 and 4 on jumper J17, and connecting the

external PWM to connector J18.

6.2 Shutdown Sequence

The backlight is shut down (LEDs turned off) by setting PWM input low or when VDDIO/EN = 0. If

VDDIO/EN is set low, the TPS61193 or TPS61193-Q1 enters low-power mode with the internal LDO

disabled.

8TPS61193EVM Evaluation Module SNVU491–October 2015

Submit Documentation Feedback

200

400

600

800

1000

1200

1400

1600

1800

2000

2200

20 40 60 80 100 120 140 160 180 200 220

fSW (kHz)

RFSET (k)

C010

www.ti.com

Boost Converter

7 Boost Converter

7.1 Switching Frequency

Switching frequency for boost is defined as 300 kHz to 2.2 MHz. However, frequency from 250 kHz to 2.2

MHz can be set by the external resistor connected to the FSET pin, thus allowing the device to be

synchronized with the lowest external frequency of 300 kHz (see details in Section 7.2).

Switching frequency is defined by resistor R3 connected to FSET pin:

ƒSW = 67600/(RFSET + 6.4)

where

• ƒSW - switching frequency, kHz

• RFSET – frequency setting resistor, kΩ(1)

Figure 5. Switching Frequency vs RFSET

By default, jumper J4 is installed on the board connecting R3 = 160 kΩto the FSET pin which sets the

boost at 400 kHz. An external resistor can be connected to change the switching frequency: remove

jumper J4, short pins 7 and 8 on jumper J17, and connect the external resistor to connector J18. Boost

internal parameters are adjusted automatically according to chosen frequency during start-up.

7.2 Spread Spectrum and Synchronization

The SYNC pin is used to enable boost spread spectrum or, alternatively, to synchronize boost switching

with an external frequency. To disable spread spectrum functionality this pin must be connected to

ground; to enable spread spectrum SYNC must be connected to VDDIO/EN. Selection is done with

jumper J3. When spread spectrum is enabled, boost switching frequency is modulated ±3% from set

frequency with 1.875 kHz modulation frequency.

If an external frequency is detected at SYNC pin, the TPS61193 or TPS61193-Q1 starts to synchronize

boost with this frequency. Frequency should be higher than the switching frequency set by RFSET resistor

and be in range 1.2 V to 1.5 V × fSW SET.

SNVU491–October 2015 TPS61193EVM Evaluation Module

200 300 400 500 600 700 800 900 1000

Maximum converter output voltage (V)

R12 (k)

C011

VMAX BOOST = ( VBG

R13 + 0.0387 ) x R12 + VBG

Boost Converter

www.ti.com

7.3 Voltage Control

Maximum boost converter voltage is defined by the feedback voltage divider R12 and R13.

Recommended value for R13 is 130 kΩ. R12 value can be calculated with the following equation:

where

• VBG = 1.2 V

• R12, R13 values are in kΩ(2)

Figure 6. Converter Maximum Output Voltage vs R12

Maximum voltage should be chosen based on the maximum voltage required for LED strings.

Recommended maximum voltage is about 30% higher than maximum LED string voltage. Initial boost

voltage is about 88% of maximum voltage. Boost output voltage is adjusted automatically based on LED

current sink headroom voltage.

Default setting for boost maximum voltage is 37 V (R12 is 750 kΩ).

10 TPS61193EVM Evaluation Module SNVU491–October 2015

Submit Documentation Feedback

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments ADS42JBx9 Bedienungsanleitung

Texas Instruments

Texas Instruments SN75LVCP600S Bedienungsanleitung

Texas Instruments

Texas Instruments Jacinto7 J721E Bedienungsanleitung

Texas Instruments

Texas Instruments DRA77xP-ACD Bedienungsanleitung

Texas Instruments

Texas Instruments BQ25756EEVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1015EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS56221EVM-579 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS3702CX33EVM-683 Bedienungsanleitung

Texas Instruments

Texas Instruments TLV841EVM Bedienungsanleitung

Texas Instruments

Texas Instruments BUF22821EVM-USB Bedienungsanleitung

Texas Instruments

Texas Instruments ADS9224REVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments TL16C750EEVM Bedienungsanleitung

Texas Instruments

Texas Instruments CC112 EM Series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS65986EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DRV5011-5012EVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS7861EVM Bedienungsanleitung

Texas Instruments

Texas Instruments AM572x series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS55065EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LMK01000 Bedienungsanleitung

Texas Instruments

Texas Instruments LM74930Q1EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LM63625QDRREVM Bedienungsanleitung

Texas Instruments

Texas Instruments CC2500EMK Bedienungsanleitung

Texas Instruments

Texas Instruments TPA3200D1 Bedienungsanleitung

Texas Instruments

Texas Instruments SN65LV1021 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung