Texecom Premier Elite AM 360DT Bedienungsanleitung
Installation Manual
Premier Elite AM 360DT
INS622-2
INS622-2 3/13
1.0 Instruction Manual
1)________________________________________________________
2)________________________________________________________
INS622-2 4/13
3)________________________________________________________
INS622-2 5/13
INS622-2 6/13
4)________________________________________________________
5)________________________________________________________
INS622-2 7/13
6)________________________________________________________
2.0 EN: Installation Sheet
Description
The Premier Elite AM 360DT is a ceiling mount dual technology detector, which is
designed to detect a movement of an intruder, and to activate an alarm on a
INS622-2 8/13
control panel. The product must be connected to a listed burglar system
compatible control unit or power supply unit, which provides a supply voltage
between 9 and 15 VDC as well as a minimum 4 hours of standby power.
Installation guidelines
The technology used in these detectors resists false alarm hazards. However,
avoid potential causes of instability such as:
Avoid mounting the detector where objects may interfere with the anti-
masking function (<1m), above doors, near curtains etc.
The detector should not be mounted in direct sunlight.
Not suitable for outdoor use.
To install the detector:
1. Unwind the screw on the side of the detector until loose; the screw will be
INS622-2 9/13
retained in the product (see Figure 1, item 1).
2. Lift detector lid out from the base and off the lugs at the opposite end to the
screw (see Figure 1, item 2).
3. Fix the base to the ceiling between 2.4 m and 3.6 m (8 and 12 ft) from the floor.
For flat mounting use a minimum of 2 screws (DIN 7998) in any of the available
positions (see Figure 2). Rear tamper pull-out needs to be secured to the mounting
surface to meet Grade 3 requirements.
4. Wire the detector (see Figures 4 and 5).
5. Select the desired option settings (see Figure 6).
On power-up the detector will temporarily enter an auto-optimisation mode to
adapt to its environment. This will be shown by the LED’s flashing in
sequence. Allow 3 minutes for the optimisation to complete.
During optimisation ensure that there are no obstructions in close proximity
(<1m) to the detector that will not be present during normal operation, as
this could trigger a false masking signal.
Triple End-Of-Line (T-EOL) (see Fig. 4)
The detector is designed to be connected to a single zone on control panels which
feature Triple End-Of-Line compatibility. Alarm, Tamper, Fault and Masking are
signalled on one pair of wires. To aid installation the resistor values can be
selected via the jumpers. All the connections are normally closed. Masking is
INS622-2 10/13
signalled by the alarm and fault relays opening simultaneously, this can
be done by changing Option 3 jumper so only the fault relay is opened.
(see Fig.6)
Fault Monitoring - A fault will be indicated by one of the following:
Supply input voltage out of specification1.
PIR sensor malfunction / microwave malfunction2.
The fault will remain until the power is cycled off/on.
This detector is capable of performing a self-test. There are two types of self-test;
a local self-test and a remote self-test.
Self-Test
To meet the requirements of EN50131-2-4 this detector is capable of performing a
self-test. There are two types of self-test, a local self-test and a remote self-test.
Local Self-Test
Local self test is controlled by the detector and runs periodically to test the
functionality of the circuitry. Setting the Local Self Test Jumper to DISABLED will
disable this function. If the test is passed no indication is shown but if it fails then a
fault will be signalled to the panel and the LED lights orange (if enabled). The fault
will remain until the power is cycled off/on.
Remote Self-Test
This test is initiated at the control panel. If the test is passed the green LED pulses
twice in quick succession and alarm signalled but if it fails then a fault will be
signalled to the panel and the LED lights orange (if enabled). The fault will remain
until the power is cycled off/on. The panel is required to set the ‘TEST’ terminal low
(0V) for activation of Remote Self Test.
Walk Test
This test is initiated at the control panel. If this terminal (RLED) is set low by the
panel (0V) the unit will enter walk test mode (when LED indication J5 is disabled).
Inhaltsverzeichnis
Andere Texecom Sicherheitssensor Handbücher
Texecom
Texecom Premier Elite MR Long Range Bedienungsanleitung
Texecom
Texecom Premier Elite AMQD Bedienungsanleitung
Texecom
Texecom Odyssey Series Bedienungsanleitung
Texecom
Texecom Reflex Bedienungsanleitung
Texecom
Texecom Prestige DT Bedienungsanleitung
Texecom
Texecom Capture A20 Bedienungsanleitung
Texecom
Texecom Impaq SC-W Bedienungsanleitung
Texecom
Texecom Premier Elite XT-W Bedienungsanleitung
Texecom
Texecom Impaq S Bedienungsanleitung
Texecom
Texecom Premier 360 DT Bedienungsanleitung
Texecom
Texecom Premier Elite Impaq Plus-W Bedienungsanleitung
Texecom
Texecom Capture P15-W Bedienungsanleitung
Texecom
Texecom Premier External TD-W Bedienungsanleitung
Texecom
Texecom CAPTURE P15 Bedienungsanleitung
Texecom
Texecom Prestige Orbit QD Bedienungsanleitung
Texecom
Texecom Premier Elite Impaq Plus-W Bedienungsanleitung
Texecom
Texecom Premier Elite ComWiFi Bedienungsanleitung
Texecom
Texecom Veritas Reflex Bedienungsanleitung
Texecom
Texecom Prestige AMDT Plus Bedienungsanleitung
Texecom
Texecom Mirage DT Petwise Bedienungsanleitung
