Texecom Premier External TD Bedienungsanleitung
Premier External TD
Installation Manual
INS352-5
1 INS352-5
1 2
3
Remove the top cap and loosen screw
(screw retained in wall plate).
Push up head unit and remove.
Use a flat head screwdriver to lever out both
sides of the terminal cover as shown.
1. Accessing the Unit
INS352-5 2
2. Choosing a Location
Parallel
✓
1.0 - 1.4m
•Mounting height 1.0 - 1.4m (nominal 1.2m), measured to middle of unit.
•Mount perpendicular to ground.
•Try to avoid direct sunlight.
•Avoid pointing at swaying bushes/trees and
swaying clothes on a clothes line. ✗
✗
•Try to install the detector so its detection area is
terminated by building/fences etc. This will reduce
the effect of range variation caused by environmental
changes.
•In the detection area try to avoid reflective surfaces
such as standing water, swimming pools or polished
floors as this can cause the detectors range or coverage
to vary as reflected signals may be seen.
✗
3 INS352-5
3. Mounting the Unit
WALL MOUNTING
For wall mounting, the
cable should be brought
through the wall into the
cable entry hole.
Cable Entry
Cable Entry
Conduit Entry
Cable
Channels
SURFACE WIRING
For surface wiring, use the appropriate knockout in the
top or bottom of the unit. If wiring from the top, use the
knockouts in the top cap and run the cable down the
cable channels and into the unit as shown.
REAR TAMPER
To enable the rear tamper, the breakaway keyhole
section must be securely fixed to the mounting surface.
Front View
Rear View
Cable Entry
Knockout in Top Cap
POLE MOUNTING
Using the pole mount kit (available separately) the unit can be mounted on poles with an outside
diameter of 20 - 57mm. Assemble the kit around the pole as shown and tighten the 4 bolts. Hook the
detector wall plate onto the kit and secure the remaining 2 bolts through the lower mounting holes.
INS352-5 4
Pole Mount Bracket Mounting
1
x4
x4
ø 45 - 57mm
ø 20 - 44mm 2
x1
3
x3
4
5
5 INS352-5
JP1: Pulse Count
4. Wiring the Unit
0.3 - 3.0m/s
3
2
4
JP2: Sensitivity
MEDIUMHIGH LOW
JP3: Alarm
NO: alarm relay normally open.NC: alarm relay normally closed.
TERMINAL BLOCK
12V & 0V: 9-16 VDC.
ALARM:NO/NC (selectable) relay output.
18 Ω, 50VDC, 100mA Max.
TAMPER:NC Relay output.
18 Ω, 50VDC, 100mA Max.
RLED:0V: LED off.
12V or No Connection: LED on.
AUX:NC relay input.
NC = Normally Closed, NO = Normally Open
JP4: LED
JP5: MODE
JP6 & JP7: END OF LINE JUMPERS
JP7
Selects the End-of-Line
resistance. Equivalent
to wiring a resistor of
the selected value as
shown.
JP6
Selects the resistance across the alarm
relay. Equivalent to wiring a resistor of the
selected value as shown.
TAMPER - JP6ALARM - JP7
Night Mode
Detector only operates at night.
Day/Night Mode
Detector is always operating.
JP8 & JP9: see Auxiliary section (page 9)
INS352-5 6
7 INS352-5
5. Range Adjustment - PIR
1.2m
2m 4m 6m 8m 10m 12m
0m
0m
1.2m
2m 4m 6m 8m 10m 12m
0m
0m
1.2m
2m 4m 6m 8m 10m 12m
0m
0m
1.2m
2m 4m 6m 8m 10m 12m
0m
0m
Position - 12m Coverage
Position - 8m Coverage
Position - 5m Coverage
Position - 2m Coverage
Selected Range Side View
Bottom of head unit
To adjust the range of the detector, rotate the
circular section shown until the desired range is
shown in the window.
Note: Range can vary due to environmental
conditions. To reduce the risk of false alarms
always select the lowest range possible for the
installation.
Specified ranges are valid for nominal 1.2m
mounting height.
2m 4m 6m 8m 10m 12m
0m
12m
10m
8m
6m
4m
2m
0m
12m 10m 8m 6m 4m 2m
Active
detection
coverage
INS352-5 8
6. Coverage Area
2m 4m 6m 8m 10m 12m
0m
12m
10m
8m
6m
4m
2m
0m
12m 10m 8m 6m 4m 2m
Active
detection
coverage
90˚
90˚
90˚
45˚
45˚
Bottom of head unit Bottom of head unit
Top View Top View
Walk-testing
With the range, sensitivity, coverage and pulse count set as desired, enable the LEDs and walk-through
the area of protection. Confirm the LEDs light and alarm relay activates.
9 INS352-5
MADE IN ENGLAND
Regulatory Information
The Premier External detector is protected
by UK & International Designs.
Premier is a Trademark of Texecom Ltd.
7. Auxiliary Input
With the Auxiliary input enabled (JP8), a second detector with a normally
closed relay output can be connected to the Premier External detector to give
directional detection. The order of activation required to give an alarm signal is
set by the direction jumper (JP9).
When this is set to ‘1st’ the auxiliary detector must be activated first followed
by the Premier External detector within 1 minute to give a valid alarm signal.
With the jumper set to 2nd, the Premier External detector must be activated
followed by the auxiliary detector within 1 minute.
If directional detection is not required, disable the auxiliary input using JP8.
AUX Premier External PIR
AUX Premier External PIR
JP8
ON
JP9
ALARM
NO
ALARM
1st
2nd
NO
ALARM
NO
ALARM
JP9
ALARM
NO
ALARM
1st
2nd
OFF
Supplier: Texecom Ltd, St. Crispin Way, Haslingden, Lancashire, BB4 4PW, UK.
Weee Directive: Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.recyclethis.info.
RoHs Directive: RoHS Compliant. Hereby, Texecom declares that this device does not
contain lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB)
or polybrominated depheny ethers (PBDE) in more than the percentage specied by EU directive,
except exemptions stated in EU directive annex.
CE Directive: Hereby, Texecom declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive.
Maintenance: Test yearly by the installer
Warranty: 2 year replacement warranty
Security grade: EN Grade 2 Environmental class: Class IV
Disclaimer: The Premier External TD is not a complete alarm system, but only its part. Therefore
Texecom does not accept any responsibility or liability for any damage that is claimed to be a
result of an incorrect functioning of the Premier External TD detector. Texecom reserves the right
to change the specication without a prior notice.
Certificate Number: FM 35285
Inhaltsverzeichnis
Andere Texecom Sicherheitssensor Handbücher
Texecom
Texecom CAPTURE D20-W Bedienungsanleitung
Texecom
Texecom Premier Elite XT-W Bedienungsanleitung
Texecom
Texecom Veritas Reflex Bedienungsanleitung
Texecom
Texecom Premier Elite ComWiFi Bedienungsanleitung
Texecom
Texecom Impaq S Bedienungsanleitung
Texecom
Texecom Premier External TD-W Bedienungsanleitung
Texecom
Texecom Premier Elite CO-W Bedienungsanleitung
Texecom
Texecom Prestige Orbit QD Bedienungsanleitung
Texecom
Texecom Veritas Medusa Bedienungsanleitung
Texecom
Texecom Premier Elite Impaq Plus-W Bedienungsanleitung
Texecom
Texecom Prestige IR Bedienungsanleitung
Texecom
Texecom Premier Elite MR Long Range Bedienungsanleitung
Texecom
Texecom Capture P15-W Bedienungsanleitung
Texecom
Texecom Capture A20 Bedienungsanleitung
Texecom
Texecom Impaq SC-W Bedienungsanleitung
Texecom
Texecom CAPTURE P15 Bedienungsanleitung
Texecom
Texecom Premier Elite DT-W Bedienungsanleitung
Texecom
Texecom Premier Elite AM360 QD Bedienungsanleitung
Texecom
Texecom Odyssey Series Bedienungsanleitung
Texecom
Texecom Prestige DT Bedienungsanleitung
