Texmate CL-B101D40HZ Bedienungsanleitung

CL-B101D40HZ Manual (d0098) Page 1

CL-B101D40HZ

Smart 101 segment, 4 digit LED Tricolor or

Mono-color digital line frequency bargraph controller

with four fully programmable set points

in a switchboard style case for

monitoring, measurement, and control applications.

0.56” LEDs

• Frequencyinput.Easilyuserscaled.

•

Optional isolated 16 bit analog output. User or factory scalable to 4

to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span

from ± one count to the full scale range of – 1999 to 9999 (12000

counts).

•

A Programmable Tricolor (Red-Green-Orange) or mono color (red or

green), 101 segment high brightness bargraph.

•

Red 4-digit LED display with a range of 99.99 to 999.9Hz

Optional green digital display.

•

FrontpanelLEDannunciatorsprovideindicationofsetpointstatus.

•

Two9AmpFormC,andtwo4AmpFormAor4x4AmpFormA

relaysavailable

•

 Auto-sensingAC/DCpowersupply.Forvoltagesbetween

85-265 V AC / 95-300 V DC (PS1)or18-48VAC/10-72VDC

(PS2).

•

 Provisiontoconnectanexternalprogramminglockoutswitch.

•

 ProvisionforexternalDIMswitchtoreducethebrightest

display setting by 50%.

•

 Automaticintelligentaveraging,smoothsnoisysignalswhile

providingafastdisplayresponsetoreallevelchanges.

General Features

Specifications

• Thebargraphcandisplay,full

scale, any desired portion of

the digital reading.

• Setpoint1hasdelay-on-make

anddelay-on-breakplusaspe-

cial “pump on pump off” mode

that creates a Hysteresis Band

between SP1 and SP2.

• Fourprogrammablesetpoints

withadjustableHysteresis.•

Software Features

Bargraph center zero function.

• Relayactivationcanbeselected

tooccurabove(hi)orbelow(Lo)

each setpoint.

• Digitaldisplayblanking.

• Decimalpointsetting.

• Four-levelbrightnesscontrol

BargraphCenterPointDisplayModeSelection ... 6

BargraphColorProgrammingMode ........ 9

CaseDimensions ...................... 13

ComponentLayout..................... 11

ConnectorPinoutsandPinDescriptions..10-11

ControlsandIndicators .................. 2

Decimal Point and Brightness Selection ..... 5

Range Selection Mode................... 7

ProgrammingConventions................ 2

SetpointSetting&RelayConfigurationMode....8-9

SoftwareFeatures ...................... 1

Software Logic Tree ..................... 3

Specifications.......................... 1

TwoPointAnalogRangeSetting&Calibration .... 7

Digital Rescaling Procedures .............. 4

Digital Span Selection for Display .......... 5

Digital Span Selection for Analog Range Output... 6

FunctionalDiagram .................... 10

GeneralFeatures ....................... 1

I-SeriesInputSignalConditioningModules ..... 12

Installationguidelines ................... 13

OrderingInformation ................... 14

LEOPARD

FAMILY

Input Specs:�� Depends on Input signal conditioner

A/D Converter:�� 14 bit single slope

Accuracy:�� ±(0�05% of reading + 2 counts)

Temp. Coeff�:�� 100 ppm/°C (Typical)

Warm up time:�� 2 minutes

Conversion Rate:�� 10 conversions per second (Typical)

Digital Display:��

4 digit 0.56" LED red (std), green (optn)

Range

–1999 to 9999 counts�

Bargraph Display:��

101 segment 235º circular red (standard),

Green (optional) or tricolor (optional) LED�

Polarity:�� Assumed positive� Displays – negative

Decimal Selection:�� Front panel button selectable, X•X•X•X•

Positive Overrange:�� Bargraph and top segments of digital display

flash�

Negative Overrange:�� First segment of bargraph and bottom seg-

ments of digital display flash�

Relay Output:�� Two 9 Amp Form C relays, two 4 Amp Form

A relays or

4x4AmpFormArelays

Analog Output:�� Isolated 16 bit user scalable mA or V

OIC (mA out) ��

4-20 mA @ 0 to 500Ω max loop resistance

OIV (volts out) �� 0-10 V DC @ 500 Ω or higher resistance

Power Supply:�� AC/DC Auto sensing wide range supply

PS1 (std)��

85-265 VAC / 95-300 VDC, 50-400Hz 4.2W

PS2��

18-48 VAC / 10-72 VDC, 50-400Hz 4�2W

Operating Temp�: �� 0 to 50°C

Storage Temp:�� –20°C to 70°C

Relative Humidity:�� 95% (non condensing)

Case Dimensions:��

Bezel (4.48"x4.48") 113.8x113.8mm

Depth behind bezel (4.23") 107.46 mm

Plus (0�48”) 12�24 mm for connectors

Weight:�� 16 oz�, 1lb 4 oz when packed

Table of Contents

Page 2 CL-B101D40HZManual(d0098)

Front Panel Buttons

Program Button

The

buttonisusedtomovefromoneprogramsteptothenext.

When pressed at the same time as the button, it initiates the

calibration mode. When pressed at the same time as the but-

ton, it initiates the setpoint setting mode.

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

toviewthesettingofthesaved Peak and Valley Values.

When setting a displayed parameter during programming, the

buttonisusedtoincreasethevalueofthedisplayedparameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level aswellastoviewthesettingof

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

buttonisusedtodecreasethevalueofthedisplayedparameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

anONorOFFsegmentdependentonthebargraphdisplaybeing

aboveorbelowthesetpoint.

Setpoints

indicated

by an ON

Segment

Setpoints indicated

by an OFF Segment

Controls and Indicators

This symbol represents the

OPERATIONALDISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and

releaseit togo onto thenext step inthe

direction indicated by the arrow. When

an alternative dotted line is shown, this

indicates that an alternative logic branch

will be followed when a particular option

is present.

When two buttons are shown side by side

and enclosed by a dotted line, they must

be pressed at the same time then released

togoontothenextprogrammingstep.

IfanXappearsthroughadigit,itmeansthat

any number displayed in that digit is not rel-

evanttothefunctionbeingexplained.

[Span]

[10000]

When the

and

buttons are shown

together,thedisplayvaluecanbeincreased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

functionandthevalue.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

valuedisplayedonthemeterdisplay.

When there are more than two display selec-

tionstheyareshowninbracketsbelowthe

first display and are also selectable by

pressing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

Toexplainsoftwareprogrammingprocedures,logicdiagramsare

usedtovisuallyassistinfollowingtheprogrammingsteps.The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

Front Panel Controls and Indicators

LED

Annunciators

for Setpoints

1-4

Single or

Tri-color

Bargraaph

Display

Button

DOWN

Button

PROGRAM

Button

7 Segments

Digital

Display

CL-B101D40HZ Manual (d0098) Page 3

Software Logic Tree

The CL-B101D40HZ is an intelligent bargraph meter with a hier-

archical software structure designed for easy programming and

operation, as shown below in the software logic tree.

vWhen power is applied, all segments of the bargraph and

digital display light up for 3 seconds. The version number of

the installed software is then displayed for 2 seconds, after

which, the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Two

Point Digital Calibration Mode and the Analog

Output Range Setting and Calibration Mode

(cLo and chi), the meter has a 15 second

program timeout. If no buttons are pressed for

15 seconds in any of the other programming

sequences, the meter will exit the program-

ming mode and return to the operational

display. Any program changes that were made

prior to pressing the

button in the preced-

ing step will not be saved.

Peak

Reset

PEAK

Reset

VA LY

Valley

PEAK & VALLEY

VIEW & RESET

Operational Display

MAIN MENU

Bargraph Center Point

Display Selection (cto)

This branch will

only appear if

the analog

output option

is installed

Back to

Operational

Display

Digital Display ON/OFF

Selection (diSP)

Sub-menu MODE

Calibration Mode

Calibration

Input

Calibration

Output

offset

(ZEro)

Scale

Factor

(SPAn)

Calibrate Analog

Output Lo

Calibrate Analog

Output Hi

Select the Digital

Reading at which

the Analog Output

Hi (chi) will occur

Select the Digital

Reading at which

the Analog Output

Lo (cLo) will occur

This branch will only

appear, if the analog

output option

is installed

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

See Page 6

DIGITAL DISPLAY ON/OFF

See Page 6

RANGE SELECTION

See Page 7

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

See Page 6

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

See Page 7

Set the Decimal

Point (dp)

Bargraph Display

Scale Lo Range

Setting (bLo)

Bargraph Display

Scale hi Range

Setting (bhi)

Display

Brightness (br)

1 Dimmest

2 Dim

3 Bright

4 Brightest

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

See Page 5

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

See Page 5

Goes directly

to Zero setting

if Analog Output

is not installed

–

4.00

–

20.00

Range

[99•99]

[9999]

[999•9]

Select one of three

Ranges: 99.99Hz,

999.9Hz or 9999Hz

PROGRAMMABLE

OFFSET AND

SCALE FACTOR

See Page 4

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

See Page 10

Tricolor Bargraph

The tri-color bargraph is designed

like a traffic light, to display either

red, orange or green, but only one

color at a time. The color to be

displayed is selected in two ways.

The first step is to select the color

to be displayed when the bar is

“below” whichever set point is set

to the lowest position.

The second step is to select the

color to be displayed when the bar

is above each specific setpoint,

regardless of the order or position

to which the set points are set.

However, if two or more setpoints

with differently specified colors are

positioned at the same set point

value, the color specified for the set

point with the highest identifying

number will be displayed. When

setpoints are set to the same value,

the SP4 color overrides the SP3

color, the SP3 color overrides the

SP2 color, and the SP2 color

overrides the SP1 color.

SETPOINT SETTING AND

RELAY CONFIGURATION MODE

See Page 9

L or h

Relays

Activation [rLYS]

(h) High

the relay

energizes

when the setpoint

is exceeded

(L) Low

the relay

energizes below

the setpoint.

Pump On Pump Off [PUM]

When PUM is selected on,

and SP2 is set at a value

higher than SP1, the SP1

relay will operate in a special

"pump on pump off"

Hysteresis mode. SP2 acts

as the upper limit and SP1

acts as the lower limit of the

Hysteresis Band.

For filling applications, rLYS

should be set to LhLh. SP1 will

then activate for inputs less than

the SP1 setpoint, and remain

ON until the SP2 setpoint is

reached.

For emptying applications,

rLYS should be set to hhhh.

SP1 will then activate for inputs

greater than the SP2 setpoint,

and remain ON until the SP1

setpoint is reached.

Set Setpoint 1

[SP1]

Delay-on-Make

[doM]

Delay-on-Break

[dob]

Setpoint 2

[SP2]

NOTE: [dom] [dob]

Functions are only

available for SP1

0 to 9999

seconds

0 to 9999

seconds

Pump

[PUM]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Setpoint 3

[SP3]

Setpoint 4

[SP4]

BRIGHTNESS AND

SETPOINT VIEW MODE

1 Dimmest

2 Dim

3 Bright

4 Brightest

Page 4 CL-B101D40HZManual(d0098)

STEP A Enter the Calibration Mode

1) Press the

and buttons at the same time. Display

toggles between [CAL] and [oFF].

Press the or button. Display changes from [oFF] to

[on].

Press the

button. Display toggles between [CAL] and

[out].

Note: If at this point, the display skips directly to STEP C and toggles

between [ScAL] and the previous [ScAL] setting, the software

is detecting that the optional analog output hardware is NOT

installed.

STEP B Select Two Point Digital Calibration of Input Signal

1) Press the or button to select CAL [iP] for input signal

calibration.

2) Press the

button. Display toggles between [oFFS] and the

previous offset setting.

STEP C Set the Offset on the Digital Display

1) Using the and buttons, adjust the digital display to

the desired offset. This is the reading that the meter will dis-

play for a zero input

2) Press the

button. Display toggles between [ScAL] and

the previous Scale factor.

STEP D Set the Scale factor on the Digital Display

Using the and buttons, adjust the meter display to

the desired Scale factor. The default value is 2000, for which a

2V input will read 2000. If the scale factor is changed the

display will change proportionately. Therefore if the Scale

factor is changed to 1000 then for the same 2V input the dis

play would read 1000.

2) Press the

button.

The Digital Rescaling is now complete.

If the Digital Rescaling was successfully completed, the

menu branches to the Digital Span Selection for Bargraph

Display (see page 6), and the display flashes [bhi] and the

previous setting.

The CL-B101D40HZManual(d0096) meter may be rescaled without applying an external signal by changing the Offset and Scale

factor.

Offset is the reading that the meter will display for a zero input. The Offset may be set to any value from -1999 to +9999. The

default value of the Offset is 000

Scale factor is the gain of the meter. The displayed reading is directly proportional to the Scale factor. The default value of the

scale factor is 2000, but it may be set to any value between -1999 and +9999.

For an input of 2V a calibrated meter will read 2000 with the default Scale factor of 2000, 3000 with a Scale factor of 3000 and

500 with a Scale factor of 500

If a linear scale is represented by mx + b, then the Scale Factor corresponds to the slope ‘m’ and the Offset corresponds to

the intercept ‘b’

The internal Signal Span is limited to 3 V DC between – 1 V DC to + 2 V DC. Outputs from an Input Signal Conditioning module

that exceed these limits will cause the meter to indicate overrange.

Note: Most input signal conditioners have provisions for analog calibration and scaling. If the meter’s digital Scale Factor is

set to 2000 and Offset set to 0000 then, any pre-calibrated signal condi-

tioner with an output that does not exceed – 1 V to + 2 V, will read correct-

ly in the meter without any further calibration.

Digital Rescaling

Digital Rescaling Procedure

MAIN MENU

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP C Offset

STEP D Scale

Factor

To Digital Span Selection for

Bargraph Display Page 6

cAL out/iP branch will only

appear if the analog output

option is installed, otherwise

cAL on goes directly to ZEro

setting

DIGITAL

RESCALING MODE

To Digital Span Selection

for Bargraph Display

See Page 7

To Two Point Analog

Output Range Setting

and Calibration

See Page 8

CL-B101D40HZ Manual (d0098) Page 5

Example

From Two Point

Digital Calibration

Mode See Page 4

STEP A

STEP B

STEP C

STEP D

See Example Above

of Bargraph Display

Scale Range

To Digital Span Selection

for Analog Range Output or

Bargraph Center Point

Display Mode Selection

on Page 6 or 7

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

STEP A Enter the Calibration Sub Menu Mode

1) Press the

and buttons at the same time. Display toggles

between[CAL]and[oFF].

2) Press the

 button. Display toggles between [bhi] and the

previous setting.

STEP B Set the Digital Span of the Bargraph Display

(See example

above)

1) Using the and buttons, adjust the display to the

desired high parameter reading, e.g. 6000 counts.

2) Press the

 button. Display toggles between [bLo] and the

previoussetting.

3) Using the and buttons, adjust the display to the

desired low parameter reading, e.g. 4000 counts.

4) Press the

button.Displaychangesfrom[4000]to[dP].

STEP C Set the Decimal Point

1) Using the and buttons, adjust the display to the

desired decimal point setting.

2) Press the

button.Displaytogglesbetween[br]andthe

 previousbrightnesssetting.

STEP D Set the Bargraph and Digital Display Brightness

1) Using the and buttons, adjust the display to the

desired brightness setting (4 is the brightest setting).

2) Press the

button.Displaytogglesbetween[Anhi]and

 theprevious[Anhi]setting.

Note: If at this point, the display skips directly to STEP G and toggles

between[Cto]and[oFF],thesoftwareisdetectingthattheoptionalanalog

output hardware is NOT installed.

Digital Span Selection For Bargraph Display

Decimal Point and Brightness Selection

Bargraph does not light

upforInputSignalsupto

3999 counts

Bargraph lights up for

InputSignalsabove

4000 counts

Bar

High

Bar

Low

Bar

High

Bar

Low

25 75

100

25 75

100

No bargraph display

Digital display

No bargraph display

Digital display

An example of setting the

digital span of the bargraph

display to be different than

the digital display range

The bargraph can be set to display full scale (0-101 bars) any portion

ofthedigitalreadingfromaminimumof100countstoamaximumof

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high parame-

ter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

Page 6 CL-B101D40HZManual(d0098)

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would

be2500counts.Ifasignalof2500countsisappliedonlyonesegmentat

the2500countmarkwilllightup.Ifasignalof4000countsisappliedthe

segments between the center segment (2500 counts) and the 4000 count

marklightup.

Ifasignalof1000countsisapplied,thesegmentsbetweenthecenterseg-

ment(2500counts)andthe1000countmarkwilllightup.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will

thenfunctionasacenterzerometer.Whenpositivesignalsareapplied,the

barwillgoupfromthecenterpoint,andwhennegativesignalsareapplied,

the bar will go down from the center point.

STEP E Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digitalvalueatwhichthe[chi]CalibratedAnalogHighoutputwill

occur.Fordigitalreadingsoutsidethedigitalspanselected,the

analogoutputwilllinearlyriseabovethevaluesetforchi,uptothe

maximumanalogoutputcapability.However,theanalogoutputwill

notgolowerthanthecalibratedvaluesetforcLo(seebelow).

2) Press the

button.Displaytogglesbetween[AnLo]and

previous[AnLo]setting.

STEP F Selecting the [AnLo] Digital Value for Analog Low Output

1) Using the and buttons, adjust the display to the desired

digitalvalueatwhichthe[cLo]CalibratedAnalogLowoutputwill

occur. ForDigitalreadingsoutsidetheDigitalSpanselected,the

analogoutputwillnotgolowerthanthecalibratedvaluesetfor

cLo.

2) Press the

button.Thedisplaytogglesbetween[cto]and

[oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

valuesfor[Anhi]analoghighand[AnLo]analoglowcanbereversedtoprovidea20to

4mA output. The digital span selected can be as small as two counts, when using the

analogoutputtofunctionasaControlorAlarmDriver.Smalldigitalspanswillcause

the high resolution 16 bit D to A to increment digitally in stair case steps.

Digital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP G

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

 button.Displaychangesfrom[oFF]to[on].

2) Press the

button.Displaytogglesbetween[diSP]and

 [on]or[oFF].

STEP H Digital Display ON/OFF Selection

 1) Tosetthedisplayto[oFF],pressthe or button.

 Displaytogglesbetween[diSP]and[oFF].

2) Press the

button.Thedisplayexitsthecalibrationmode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

Ifthedigitaldisplayisselectedtobeoff,pressinganybuttonto

makeprogrammingchangesortoviewsetpointsactivatesthedigitaldisplay.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Operational Display

STEP G

STEP H

See Example of Bargraph

Center Point Display Mode

Selection Above

From Digital Span Selection

for Analog Range Output Above

or Direct From Decimal Point

and Brightness Selection Page 5

if Analog Output Option is Not Present

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

STEP E

STEP F

This branch will only

appear if the analog

output option is installed

To Bargraph Center

Point Display Mode

Selection Below

From Decimal Point and

Brightness Selection

See Page 5

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

-1V +1V

0.800

-0.800

-1V +1V

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

05000

5000

2500

4000

5000

2500

1000

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

Unipolar Signal Input Bipolar Signal Input

CL-B101D40HZ Manual (d0098) Page7

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP E

Calibrate

Analog

Output

STEP F

Calibrate

Analog

Output

Will only appear if the analog

output option is installed

To Digital Span Selection

for Bargraph Display

See Page 5

To Two Point Digital

Calibration Mode

See Page 4

Operational Display

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

–x

4.00

–x

20.00

Determine if the Analog Output Selection Header is in the 4 to 20mA (0-20mA) posi-

tionorthe0to10VDCposition.Ifnecessary,themodulemayhavetoberemoved

andtheheaderpositionchanged(seeComponentLayoutbelow).

Note:Alwaysdisconnectpowerfromthemeterbeforeremovingtheanalogoutputmod-

ule to adjust the mA or Volts output selection header and reinstalling it. When power is

reconnected, the meter’s software will automatically detect the presence or absence of

the analog output module.

STEP A Enter the Calibration Mode

1) Press the

and buttonsatthesametime.Displaytogglesbetween[cAL]

and[oFF].

2) Press the or button.Displaychangesfrom[oFF]to[on].

3) Press the

 button. Display toggles between [cAL] and [out] input

calibration.

Note:IfatthispointthedisplayskipsdirectlytotogglebetweenZeroandtheprevi-

ousZerosetting,thesoftwareisdetectingthattheoptionalanalogoutputhardware

is NOT installed.

STEP B

Enter the Two Point Analog [ouT] Output Range Setting and Calibration

Mode

1) Press the

 button. Display toggles between [cLo] and an internal

scale factor.

STEP E SetorCalibrate[cLo]theLowAnalogValueoftheAnalogOutputRange

 1) Connectamultimetertoanalogoutputpins17and18(seeRearPanel

Pinouts on page 10). Using the and buttons, adjust the analog out-

puttothedesiredlowvalueasmeasuredonthemultimeter.cLomaybe

adjustedtoanyvaluefrom–0.3mAto18mA(mAoutputselected)orfrom

–0.6 V to 8 V (volt output selected).  However, the output of cLo must

alwaysbelessthanthevalueselectedforchi.Ifareversedanalogoutput

is desired, the values selected to establish the Digital Span can be

reversed(seetopofpage6).FordigitalreadingsoutsidetheDigitalSpan

selected,theanalogoutputwillnotgoanylowerthanthecalibratedvalue

setforcLo.However,theanalogoutputwilllinearlyriseabovethevalue

set for chi, up to the the maximum analog output capability (see chi

below).

2) Press the

 button. Display toggles between [chi] and an internal

scale factor.

STEP F SetorCalibrate[chi]theHighAnalogValueoftheAnalogOutputRange

1) Using the and buttons, adjust the analog output to the desired

highvalueasmeasuredonthemultimeterdisplay.chimaybeadjustedto

anyvaluefrom18mAto24mA (mAoutput)orfrom8Vto10.3V (volt

output).However,thevaluemustbehigherthanthevalueselectedforcLo.

FordigitalreadingsoutsidetheDigitalSpanselected,theanalogoutput

will linearly rise above the value set for chi, up to the maximum analog

output capability.

2) Press the

button.Themeterexitsthecalibrationmodeandreturns

to the operational display.

Note: The analog output range established by the values selected for cLo and chi will

occur,automaticallyscaled,betweenthetwodigitalvaluesselectedforAnHiandAnLo.

However,

theanalogoutputcanlinearlyriseabovethechivaluesetfordigitalreadings

outside the digital span selected. See Digital Span Selection on page 6.

Two Point Analog Output Range Setting and Calibration

STEP I Select the Range

1) Using the and buttons, select the required range.

There are three ranges of 99.99Hz, 999.9Hz and 9999Hz

2) Press the

button.Thedisplayexitsthecalibration

mode and returns to the operational display.

The Display/Bargraph settings are now complete.

Two Point Analog Output Range Setting and CalibrationRange Selection Mode

Operational Display

From Bargraph Center Point

Display Mode Selection

on page 6RANGE SELECTION

Range

[99•99]

[9999]

[999•9]

Page 8 CL-B101D40HZManual(d0098)

Operational Display

SETPOINT SETTING

AND RELAY

CONFIGURATION MODE

STEP A

STEP B

STEP C

STEP D

No [doM] or [dob]

STEP E

STEP F

STEP G

STEP H

STEP I

STEP J

STEP K

STEP L

To Step M of Setpoint

Setting and Relay

Configuration Page 9

Thefollowingprogrammingstepsarerequiredtoenterthesetpointvaluesandconfiguretherelayfunctions

in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints

withoutrelaysareoperationalinsoftwarefortri-colorcontrolordisplayonlypurposes.Toremoveunwanted

setpointindications,setthemto9999or-1999dependingontherelayactivationmodeselected.

STEP A Enter the Setpoint Mode

1) Press the

and buttonsatthesametime.Displaytogglesbetween[SP1]andtheprevious

SP1 setting.

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons,adjustthedisplaytothedesiredSP1value.

2) Press the

button.Displaytogglesbetween[doM]andtheprevious[doM]setting.

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons,adjustthedisplaytothedesired[doM]value(0to9999seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

therelaywillmakecontact(energize).

2) Press the

button.Displaytogglesbetween[dob]andtheprevious[dob]setting.

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons,adjustthedisplaytothedesired[dob]value(0to9999seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

beforetherelaywillbreakcontact(de-energize).

2) Press the

button.Displaytogglesbetween[hYSt]andtheprevious[hYSt]setting.

STEP E Select the Hysteresis [hYSt]

Using the and buttons,selecttheHysteresistobeONorOFF.

2) Press the

button.DisplaytogglesbetweenPUMand(on)or(oFF).

STEP F Select Pump [PUM] (on) or (oFF)

Using the and buttons,selectthePumptobeONorOFF.WhenPUMisselectedON,and

SP2issetatavaluehigherthanSP1,theSP1relaywilloperateinaspecial"pumponpumpoff"mode.

SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay.

For filling applications:

[rLYS]shouldbesetto[LhXX](seestepM).TheSP1relayandSP1LEDAnnunciatorwillthenactivateforinputs

less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached.

For emptying applications:

[rLYS]shouldbesetto[hhXX](seestepM).TheSP1relayandSP1LEDAnnunciatorwillthenactivateforinputs

greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached.

2) Press the

button.Displaytogglesbetween[SP2]andthepreviousSP2setting.

STEP G Set Setpoint 2 (SP2)

1) Using the and buttons,adjustthedisplaytothedesiredSP2value.

2) Press the

button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.

STEP H Select the Hysteresis [hYSt]

Using the and buttons,selecttheHysteresistobeONorOFF.

2) Press the

button.Displaytogglesbetween[SP3]andtheprevious[SP3]setting.

STEP I Set Setpoint 3 (SP3) (No[doM]or[dob])

1) Using the and buttons,adjustthedisplaytothedesiredSP3value.

2) Press the

button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.

STEP J Select the Hysteresis [hYSt]

Using the and buttons,selecttheHysteresistobeONorOFF.

2) Press the

button.Displaytogglesbetween[SP4]andtheprevious[SP4]setting.

STEP K Set Setpoint 4 (SP4) (No[doM]or[dob])

Using the and buttons,adjustthedisplaytothedesiredSP4value.

2) Press the

button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.

STEP L Select the Hysteresis [hYSt]

Using the and buttons,selecttheHysteresistobeONorOFF.

2) Press the

button.Displaytogglesbetween[rLYS]andthepreviousrelaysetting.

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

CL-B101D40HZ Manual (d0098) Page 9

STEP M

STEP N

STEP O

STEP P

STEP Q

STEP R

STEP S

STEP T

STEP U

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

Operational Display

From From Step L of

Setpoint Setting and Relay

Configuration Page 8

L or h

Tocomplywiththelatestsafetyrequirements,thetri-colorbargraphisdesignedlikeatrafficlight,to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (StepQ)istoselectthecolortobedisplayed,whenthebaris“below*”,whicheversetpointisset

to the lowest position.

Second (StepsR,S,T,andU)istoselectthecolortobedisplayedwhenthebarisaboveeachspecific

set point, regardless of the order or position to which the set points are set.

However,iftwoormoresetpointswithdifferentlyspecifiedcolorsarepositionedatthesamesetpoint

value,thecolorspecifiedforthesetpointwiththehighestidentifyingnumberwillbedisplayed.When

setpointsaresettothesamevalue,theSP4coloroverridestheSP3color,theSP3coloroverridesthe

SP2color,andtheSP2coloroverridestheSP1color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position

1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]

2) Press the

button.Displaytogglesbetween[CSP1]andthepreviouscolorsetting.

STEP R Select Bargraph Color when the bar is ABOVE* SP1 Setpoint

1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]

2) Press the

button.Displaytogglesbetween[CSP2]andthepreviouscolorsetting.

STEP S Select Bargraph Color when the bar is ABOVE* SP2 Setpoint

1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]

2) Press the

button.Displaytogglesbetween[CSP3]andthepreviouscolorsetting.

STEP T Select Bargraph Color when the bar is ABOVE* SP3 Setpoint

1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]

2) Press the

button.Displaytogglesbetween[CSP4]andthepreviouscolorsetting.

STEP U Select Bargraph Color when the bar is ABOVE* SP4 Setpoint

1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]

2) Press the

button. Themeter exitsthesetpoint modeand returnstotheoperational

display.

The Bargraph Color programming mode is now complete.

STEP M Set Relay Activation mode [rLYS] for SP1

 (h)Hightherelayenergizeswhenthesetpointisexceeded.(L)Lowtherelayenergizesbelow

the setpoint. The setpoint is indicated from left to right SP1, SP2, SP3, SP4.

1) Using the and buttons, select (L) or (h) for the first digit, which corresponds to SP1.

2) Press the

button.TheSP2RelayActivationdigitbeginstoflash,anditsdecimalpointislit.

STEP N Set High (h) or Low (L) for SP2

Using the and buttons, select (L) or (h) for the second digit, which corresponds to SP2.

Press the

button.TheSP3RelayActivationdigitbeginstoflash,anditsdecimalpointislit.

STEP O Set High (h) or Low (L) for SP3

1) Using the and buttons, select (L) or (h) for the third digit, which corresponds to SP3.

Press the

button.TheSP4RelayActivationdigitbeginstoflash,anditsdecimalpointislit.

STEP P Set High (h) or Low (L) for SP4

Using the and buttons, select (L) or (h) for the fourth digit, which corresponds to SP4.

2) Press the

button.

Ifamono-colorredorgreendisplayisinstalledthentheSetpointRelayProgrammingModeisnowcompleteandthe

meter returns to the operational display.

IfatricolorbargraphdisplayisinstalledthentheBargraphColorProgrammingModewillbeenteredand

displaytogglesbetween[CoL]andtheprevioussetting.Colorselectionmenuwillbedisplayed.

Setpoint Setting and Relay Configuration Mode Continued

Bargraph Color Programming Mode

Page 10 CL-B101D40HZManual(d0098)

DIM

Lock

Analog Output

Hold

N/C

SP4

SP3

GND

+5 V

N/C

+ 5 V

SP1

MOV

+ 5 V

SP2

MOV

Display

Driver

Multiplexer

and

Buffer

Amplifier

Micro

Processor

100K

0.1

Input Hi

Input Lo

+5VDC

-5VDC

+24VDC

Ref Hi

Analog Comm

System GND

MUXO

24 V Return

GND

+ 5 V

14 Bit

Single

Slope

A to D GND

+ 5 V

GND

+ 5 V

There are input

modules for almost

any input signal.

Input and Output

pins vary for

different modules.

Smart Modules

incorporate their own

A / D converters and

communicate digitally

with the meter.

See section on

I-Series Input Modules

for connection details.

INPUT MODULES

PROCESSOR BOARD

AC Neutral,

– DC

AC Line,

+ DC

Volts mA

HEADER

Chassis Ground Tab for Optional Metal Case

Socket for Input Signal

Conditioning Module

Common

Mode Line

Choke

Bridge

Rectifier

PTC for HI Voltage

Fuse for LO Voltage

Isolated Feed Back

Isolated

Switching

Power

Supply

Controller

-5 VDC

+18 VDC ISO

–

+5 VDC

GND

+24 VDC

LC Filter

RELAY MODULES

NO3

COM 1 & 3

NO1

NC1

NO4

COM 2 & 4

NO2

NC2

MOV's

+ 5 V

SP3

+ 5 V

SP1

MOV's

+ 5 V

SP4

+ 5 V

SP2

- O/P

+ O/P

ANALOG

OUTPUT

+18V

ISO

+5VDC

Isolated

Analog

Output

Dual

or Single

ANALOG OUTPUT

MAIN BOARD

24V ISO RTN

GND

Output pins vary for different relay output modules.

August 13, 2002

CARRIER BOARD

1 3 5 7

2 4 6 8

LOCK

No Function

COMMON

DIM

DISPLAY BOARD

Relay Activation LEDs

Bargraph

Segments

Digital Display

Programming Buttons

Functional Diagram

Pinout Diagram

The Rear View of the Meter diagram shows the meter with the

relay configuration: dual 9 Amp Form C and dual 4 Amp Form

A relays� An analog output module is also shown as installed�

The CL-B101D40HZ uses plug-in type screw terminal connectors

for all input and output connections� The power supply connec-

tions (pins 14 and 15) have a unique plug and socket outline

to prevent cross connection� The main board and input signal

conditioner use right-angled connectors as standard� The output

module uses straight-thru connectors as standard�

Auto-sensing AC/DC power supply� For voltages between

85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC (PS2).

WARNING: AC and DC input signals and power supply

voltages can be hazardous. Do Not connect live wires to

screw terminal plugs, and do not insert, remove or handle

screw terminal plugs with live wires connected.

17 16

14 158 9 10 11

See Leopard Family Input

Signal Conditioning Modules

1 2 3 4 5 6

21 20 19

Relay Outputs Reserved for RS-485

LOCK

COMMON

No Function

DIM

ANALOG

OUTPUT –

Neutral

– DC

Line

+ DC

ANALOG

OUTPUT +

29 28 27 26 25 24 23 22

Standard plug-in screw terminal connectors provided by Texmate:

Connector Pinouts

Input Signal – Pins 1 to 6

Pins 1 to 6 are reserved for the input signal conditioner�

See the data sheet for the selected input signal conditioner�

Pins 8 to 11 – Rear Panel Function Pins

Pins 8 to 11 provide functions that can be implemented

with an external switch. Their pin definitions are:

Pin 11 DIM. By connecting the display dim (DIM) pin to

the COMMON pin, the display brightness setting

is halved�

Pin 10 COMMON. To activate the LOCK or DIM

functions from the rear of the meter, the

respective pins have to be connected to the

COMMON pin� This pin is connected to the

internal power supply ground�

Pin 9 No function

Pin 8 LOCK. By connecting the LOCK pin to the

COMMON pin, the meter's programmed

parameters can be viewed but not changed�

Inhaltsverzeichnis

Andere Texmate Messgerät Handbücher

Texmate

Texmate Tiger 320 Series Betriebsanleitung

Texmate

Texmate LEOPARD DL-40US-PROCESS Bedienungsanleitung

Texmate

Texmate Leopard Series Bedienungsanleitung

Texmate

Texmate UM-40-ACV Bedienungsanleitung

Texmate

Texmate BL-40PSF-PROCESS Bedienungsanleitung

Texmate

Texmate BL-40PSF-DCA Bedienungsanleitung

Texmate

Texmate UM series Bedienungsanleitung

Texmate

Texmate FL-B101Q-DCA Bedienungsanleitung

Texmate

Texmate SM-35 Bedienungsanleitung

Texmate

Texmate CM-35XTL Bedienungsanleitung

Texmate

Texmate Leopard Series Bedienungsanleitung

Texmate

Texmate DL-40 Bedienungsanleitung

Texmate

Texmate FL-B101D40H Bedienungsanleitung

Texmate

Texmate Leopard Series Bedienungsanleitung

Texmate

Texmate DL-40JANUS Bedienungsanleitung

Texmate

Texmate PM Series Bedienungsanleitung

Texmate

Texmate UM-35ACI1 Bedienungsanleitung

Texmate

Texmate CL-B101D40-TCRTD Bedienungsanleitung

Texmate

Texmate Tiger 320 Series Konfigurationshandbuch

Texmate

Texmate DX-35-XX-PS1 Merkblatt

Texmate

Texmate DI-60AE Bedienungsanleitung

Texmate

Texmate BX-B31 Bedienungsanleitung

Texmate

Texmate CL-B101D40RPM Bedienungsanleitung

Texmate

Texmate DL-40PSF-DCA Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung