The Handy THTS Bedienungsanleitung

OPERATOR’S MANUAL & PARTSLIST

MODEL –THTS

80lbs TOWED SPREADER

Spares & Support: 01793 333212

Please read & understand this manual, paying particular attention to the

safety instructions, before use.

The manufacturer reserves the right to change the product specification and

livery according to continued product improvements.

193849001 19/06/2015

Assembly Is Required

This product requires assembly before use. See the “Assembly” section for instructions.

Please check that all parts required for the assembly of this spreader are included. If for any reason

you believe a part for the assembly is missing or damaged, please contact us.

CONTENTS

SAFETY INSTRUCTIONS

SPECIFICATION

MAINTENANCE

COMPONENTS

ASSEMBLY

OPERATION

RATE SETTINGS

PARTS DIAGRAM

PARTS LIST

WARRANTY

NOTES

DO NOT USE WITH ROCK SALT.

Using rock salt in this spreader will damage the mechanism and shorten the life of the product.

Refined ice melting salt can be used but the user should be aware that this is not a specialised salt

spreader and using salt may corrode the spreader and reduce the life of the machine. Clean the

spread thoroughly after using refined de-icing salt.

SAFETY INSTRUCTIONS

Read and understand the owner’s manual and labels affixed to the machine. Learn its application

and limitations as well as the specific potential hazards. Retain these instructions for future

reference. The operator is responsible for following the warnings & instructions in this manual and

on the product.

Before each use, check that there is no damage to the spreader & that all fixings are tight & secure.

Replace or repair damaged parts. Use only approved parts. Unauthorised parts may be dangerous and will

invalidate the warranty.

Ensure that the operator is fully trained and competent to operate the spreader.

Ensure that all chemical safety instructions are adhered to when handling products for use in the

spreader.

Always distribute the load evenly.

Ensure all non-essential personnel keep a safe distance when the spreader is in use.

Keep hands and feet away from moving parts.

DO NOT overload the spreader - see Specification.

DO NOT leave unattended, especially when loaded.

DO NOT allow anybody to sit, stand, or ride on the spreader.

DO NOT allow untrained personnel to use the spreader.

DO NOT allow children to play in or climb onto the spreader.

DO NOT use on windy days when spreading seeds or herbicides.

DO NOT use the spreader for purposes other than for which it is designed.

DO NOT operate the spreader when you are tired or under the influence of alcohol, drugs or intoxicating

medicines.

Avoid large holes and ditches when using the Trailer.

Be careful when operating on steep gradients (hills) the Trailer may tip over.

Always operate at a reduced speed in rough terrain, along creeks, ditches and on hillsides.

Do not operate close to creeks, ditches and public roads.

To avoid personal injury and/or equipment damage DO NOT EXCEED 10 MPH

WARNING! Failure to comply with these instructions may result in damage to the spreader or other

property and/or personal injury.

Safety Alert Symbol. Used to alert you to potential personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in serious injury

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION

Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may

result in property damage.

SPECIFICATION

Model

THS50

Product Number

193848001

Weight

10.3kg

Capacity (Weight)

23kg

Wheel Diameter

176mm

Tyre

4.10/3.50-6

Tyre Rating

2 Ply

Tyre Maximum PSI

25psi (Do not exceed)

The manufacturer reserves the right to change the product specification and livery according to

continued product improvements.

MAINTENANCE

Maintenance spray or multi-purpose grease can be applied to the wheel axle prior to long-term

storage. Oiling is not necessary

DO NOT open the gearbox. The gears are permanently lubricated from the factory and do not

need oiling.

Prior to using the Spreader, ensure the tyres are sufficiently inflated. We recommend the use of

FOOT or HAND inflation devices only. Do not inflate above 25psi.

After each use thoroughly wash the spreader and clean material out of the hopper.

Never allow material to stay in the hopper for extended periods of time

Before storing, ensure that the spreader is clean and dry.

Store indoors or in a protected area during severe weather and in the winter months.

Periodically check all fastenings are tight & secure.

To avoid damaging the spreader, never exceed the rated load capacity of 23kg.

COMPONENTS

ASSEMBLY

STEP 1

Install the impeller onto the gearbox and axle assembly.

Align the impeller with the hole on the axle, located nearest the gearbox.

Insert M4x20 screw, through the side of the impeller and the gearbox axle. Tighten until

secure.

STEP 2

Place hopper upside down and install the u-frame using 4x M6x40 screws. Tighten until

secure.

STEP 3

Install the wheel assembly frame (with outer bushing) on each side of the gearbox axle,

ensuring the axle fixing hole is located as imaged below.

Insert M6x50 hex bolt through wheel assembly & hopper frame and secure with M6 lock nut.

Do not fully tighten the bolts.

STEP 4

Install the end of the frame brace onto the hopper frame using M6x35 hex bolt & M6 lock nut.

Install the other end of the frame brace and fix using M6x45 hex bolt.

Do not fully tighten the nuts and bolts.

STEP 5

Slide the inner axle bushing over the axle and into the outer axle bearing on both sides as

shown.

Attach wheels to the axle and fix with a M5x45 hex bolt.

Place flat washer ø16 onto one end of axle as shown and then fix the end caps onto both wheels

STEP 6

Install the pivot and bracket assembly onto the lower handle using a M6x45 hex bolt and a M6

lock nut.

Now go back and tighten all the nuts and bolts, starting at Step 1.

Do not over tighten.

STEP 7

The upper handles have three positions for the operator’s comfort. The upper handle can be

fitted to either of the two holes nearest the handle grip.

To fix, insert a hex bolt through the hole, the handle spacer and the other handle.

•Fix with a M6 lock nut.

•Do NOT tighten the nut yet.

Attach the gauge to the left hand side using M6x45 hex bolts & M6 lock nuts.

Tighten the lock nuts on the gauge first, then the handle.

STEP 8

Push the handle to the lowest position.

•Take off one of the nuts on the pivot and bracket assembly and insert head of threaded pole

into the hole of this part.

•Reattach the nut and tighten

STEP 9

•Insert the pivot rod to the shut-off plate as shown.

•Secure with a flat washer ø6 & a M6 lock nut.

Andere Handbücher für THTS

Inhaltsverzeichnis

Andere The Handy Streuer Handbücher

The Handy

The Handy THDS Bedienungsanleitung

The Handy

The Handy THTS Bedienungsanleitung

The Handy

The Handy THS80 Bedienungsanleitung

The Handy

The Handy THTS175 Bedienungsanleitung

The Handy

The Handy THS125 Bedienungsanleitung

The Handy

The Handy THSSALT Montage- und Wartungsanleitung

The Handy

The Handy THS70HDUTY Bedienungsanleitung

The Handy

The Handy THS80 Montage- und Wartungsanleitung

The Handy

The Handy THS125HDUTY Bedienungsanleitung

The Handy

The Handy THSS80 Bedienungsanleitung

The Handy

The Handy THDS Montage- und Wartungsanleitung

The Handy

The Handy THSS100 Bedienungsanleitung

The Handy

The Handy THS50 Bedienungsanleitung

The Handy

The Handy THS50 Montage- und Wartungsanleitung

The Handy

The Handy THS80 Bedienungsanleitung

The Handy

The Handy THS125 Montage- und Wartungsanleitung

The Handy

The Handy THSSALT Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung