Thomas&Betts STA-KON WT3185 Referenzhandbuch

BLUE - 6 GA

BROWN - 2 GA

GREEN - 1 GA

BLACK - 2/0

PURPLE - 4/0

8 GA - RED

4 GA - GRAY

1/0 - PINK

3/0 - ORANGE

250 MCM - YELLOW

ADJUSTABLE CRIMPER

INSTALLATION AND GAUGING PROCEDURE

For 8 GA to 250 MCM Uninsulated STA-KON®Terminals

Catalog Number WT3185

WARNING

HANDLES ARE NON-INSULATING.

DO NOT CRIMP ON ENERGIZED WIRES.

1. Strip cable without cutting or nicking the strands.

2. Select the side of the tool according to the type of

connector and cable combination to be installed.

3. Move indenter by turning the adjusting wheel until

the pointer slot aligns with the selected cable size

line. The wheel should be in a positive detented

position (See ﬁgure 1).

INSTALLING PROCEDURE

TA01390 C page 1 of 2

4. Insert cable into connector barrel until it bottoms.

5. Locate connector in the tool between the die nest

and indenter (See Figure 2).

6. Crimp connector by closing the handles. Apply

as many crimps as required. Refer to instructions

packed with connectors for required number of

crimps.

Connector

Cable Size

Line

Nest

Indenter

Adjusting

Wheel

Type of Cable

Figure 1 Figure 2

Die Nest

Connector

Die Indentor

Cable

WARNING

WT3185 is equipped with th SHURE-STAKE®Full Stroke

Compelling Mechanism. Keep ﬁngers and other body

parts clear of die nest during operation of this tool.

Pointer Slot

GAUGING PROCEDURE

For Parts or Service, contact the tool service center at 1-800-284-TOOL (8665).

CHECKING HANDLE ADJUSTMENT

1. Lay the tool on a ﬂat surface as shown in Figure 3.

Open handle and release it so that it will close of its

own weight.

2. Measure the handle spread distance at the inner

surface of the handle tips as shown in Figure 3.

3. If the distance is 14”±1/2” the tool is adjusted

properly. If not, the tool should be adjusted.

HANDLE ADJUSTMENT PROCEDURE

Adjustment Screw

HANDLE ADJUSTMENT PROCEDURE

1. Turn Adjustment screw clockwise to increase

handle spread and counterclockwise to decrease

handle spread (Refer to Figure 3).

14” ±1/2”

Figure 3

TA01390 C page 2 of 2

WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine

the suitability of this product for the user’s intended application. Thomas & Betts warrants that this product will be free from defects

in materials and workmanship for the period stated on the enclosed warranty card. Upon prompt notiﬁcation of any warranted

defect, Thomas & Betts will, at its option, repair or replace the defective product or refund the purchase price. Proof of purchase is

required. Misuse or unauthorized modiﬁcation of the product voids all warranties.

Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN

LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY

FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF REPAIR OR REPLACEMENT OF THE PRODUCT,

AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Thomas & Betts Corporation

Memphis, Tennessee

www.tnb.com

1. Close the tool jaws until they bottom.

2. Select the side of the tool to be gauged (Tubular or Brazed).

3. Move indenter until the pointer slot aligns with the selected cable size. The adjusting wheel should be in a

positive detented position. For brazed seam conductors select 6 GA. For tubular connectors select 2/0.

4. Gauge the crimping area with a suitable pin gauge. The gauge diameter must fall within .405 ±.010 for 2/0

tubular and .215 ±.010 for 6 GA brazed products.

Inhaltsverzeichnis

Andere Thomas&Betts Crimpwerkzeuge Handbücher

Thomas&Betts

Thomas&Betts BPLT14BSCR Bedienungsanleitung

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4002 Bedienungsanleitung

Thomas&Betts

Thomas&Betts Comfort Crimp ERG2002 Bedienungsanleitung

Thomas&Betts

Thomas&Betts ERG2001 Bedienungsanleitung

Thomas&Betts

Thomas&Betts TBM5 Bedienungsanleitung

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4008 Bedienungsanleitung

Thomas&Betts

Thomas&Betts COLOR-KEYED TBM14RH Bedienungsanleitung

Thomas&Betts

Thomas&Betts TBM6 Bedienungsanleitung

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4004 Bedienungsanleitung

Thomas&Betts

Thomas&Betts Blackburn Comfort Crimp TBM45S Bedienungsanleitung

Thomas&Betts

Thomas&Betts Blackburn TBM62PCR-LI Bedienungsanleitung

Thomas&Betts

Thomas&Betts BP4UCR Bedienungsanleitung

Thomas&Betts

Thomas&Betts Blackburn COMFORT CRIMP TBM41E Bedienungsanleitung

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4006 Bedienungsanleitung

Thomas&Betts

Thomas&Betts Stakon Comfort Crimp ERG4255 Bedienungsanleitung

Thomas&Betts

Thomas&Betts QUICK-KON TNB170-ELECDIE Bedienungsanleitung

Thomas&Betts

Thomas&Betts BPLT14BSCRI Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung