THORLABS GCM102 Bedienungsanleitung

HA 0371T

GCM102(/M)

30 mm Cage System Mount

For Small Beam Diameter Galvos

User Guide

Original Instructions

GCM102(/M) 30 mm Cage System Mount for GVSx02 Series Galvos

Contents

Chaper 1 Overview ..................................................................................................... 1

1.1 Description ......................................................................................... 1

Chaper 2 Safety .......................................................................................................... 2

2.1 Safety Information ............................................................................. 2

Chaper 3 Installation .................................................................................................. 3

3.1 Installing the Galvo Motors ............................................................... 3

3.2 Fitting the Optics and Adapters ....................................................... 8

3.3 Using the Cage Mount with Other Equipment ............................... 11

3.3.1 Mounting to a 1.5” Diameter Post ......................................................... 11

3.3.2 Mounting to 66 mm Rail Components .................................................. 12

Chaper 4 Thorlabs Worldwide Contacts ................................................................ 14

Rev B Jan 2018 Page 1

Chapter 1 Overview

1.1 Description

The GCM102(/M) cage system adapter is used to mount the GVSX02 dual-axis galvo

systems into a 30 mm cage system. The galvo motors can be fitted and aligned

without dismantling the mount

On the beam input side, the mount features SM1 and SM05 threads for mounting lens

tubes. The output side is threaded SM2, which can be converted to M25 x 0.75 by

fitting the GCMA1 or SM2A33 adapters. The mounting face features an array of M6,

M4 and M3 (1/4-20, 4-40 and 8-32 UNC) threaded holes for use in mounting to our

range of 1.5 OD posts, and XT66 construction rails.

Note: The input and output beams are on different planes. Cage systems should be

adapted accordingly.

Fig. 1.1 GCM102 Cage Mount, post mounted with lens and cage rods fitted

Page 2 ETN032532-D02

GCM102(/M) 30 mm Cage System Mount for GVSx02 Series Galvos

Chapter 2 Safety

2.1 Safety Information

For the continuing safety of the operators of this equipment, and the protection of the

equipment itself, the operator should take note of the Warnings, Cautions and Notes

throughout this handbook and, where visible, on the product itself.

The following safety symb ols may be used throughout the handbook and on the

equipment itself.

Warning: Risk of Electrical Shock

Given when there is a risk of injury from electrical shock.

Warning

Given when there is a risk of injury to users.

Caution

Given when there is a risk of damage to the product.

Note

Clarification of an instruction or additional information.

Rev B Jan 2018 Page 3

Chapter 3 Installation

3.1 Installing the Galvo Motors

1) Using a 2.5 mm hex key, loosen the pinch bolts on the existing mount, and remove

the motor/mirror assemblies. Leave the spacers fitted to the motors and retain the

insulating film for later use. Take care not to touch the mirror surfaces.

2) Once removed, check that the the rmal insulation film is u ndamaged. Damaged

material should be discarded. Replacement film is supplied with the cage mount.

Fig. 3.1 Removing Motor/Mirror Assemblies

3) Using a 3 mm (1/8”) hex key, remove the blanking plugs from the body of the

GCM102(/M) Cage Mount, to gain access to the motor clamp.

Using a 2mm ( 5/64”) hex key, loosen the clamp bolts.

Fig. 3.2 Loosening the motor clamp bolts

Removing the blanking plugs Loosening the motor clamp bolts

Page 4 ETN032532-D02

GCM102(/M) 30 mm Cage System Mount for GVSx02 Series Galvos

4) Position the cage mount assembly as shown in Fig. 3.3 and using a 2 mm (5/64”)

hex key, remove the screws securing the small gasket cover. Remove the gasket

cover, then remove the screws securing the large gasket cover.

Fig. 3.3 Removing the Gasket Covers

5) Position the cage mount assembly as shown in Fig. 3.4 and using a 2 mm (5/64”)

hex key, remove the remain ing screws se curing the large gasket cover, then

remove the gasket cover.

Fig. 3.4 Removing the Gasket Covers

6) Position the cage mount as shown in Fig. 3.5, with the fixed side of the gasket to

the left. Slide the large spacer underneath the gasket then pull the gasket over the

Rev B Jan 2018 Page 5

Chapter 3 Installation

spacer such that it pushes through the hole in the gasket, and the gasket fits tights

around the sides of the spacer..

Fig. 3.5 Inserting the Large Spacer

7) Reposition the cage mount as shown in Fig 3.6, and in sert the small spa cer

underneath the gasket. Pull the gasket over the spacer such that it pushes through

the hole in the gasket, and the gasket fits tights around the sides of the spacer.

Fig. 3.6 Inserting the Small Spacer

Page 6 ETN032532-D02

GCM102(/M) 30 mm Cage System Mount for GVSx02 Series Galvos

8) Roll up the thermal insulation film into a small tube shape and insert into the motor

mounting holes as shown below. Ensure the film is pushed fully into the hole.

Fig. 3.7 Fitting the thermal insulation film

9) Place the cage adapter body on the worksurface as shown below, with the

engraving on the left, and the large open face facing away and to the right.

Fig. 3.8 Inserting the Motors

10) Identify the X-Axis motor assembly. This is the motor with the smallest mirror and

the serial number label has a suffix ‘-X’.

11) Insert the motor into the lower mount on the left hand side - see Fig. 3.8 Detail A.

Caution. Ensure that the wide spacer and the thermal insulation detailed

previously are fitted. The X-axis mirror will be misaligned without the wide

spacer. The clamp pinch bolts will not tighten sufficiently without the

thermal insulation material.

Gently twist the motor bod y as it is pu shed into the clamp, ta king care not to

damage the thermal insulation material.

Detail A Detail B

Rev B Jan 2018 Page 7

Chapter 3 Installation

12) Ensure that the narrow plastic spacer removed at item (1) is fitted to the remaining

mounting hole, then insert the Y-axis motor into the upper mount on the right hand

side- see Fig. 3.8 Detail B.

Caution. Ensure that the thermal insulation detailed at item (4) is fitted. The

clamp pinch bolts will not tighten sufficiently without this material.

Gently twist the motor bo dy as it i s pushed into the clamp, taking care not to

damage the thermal insulation material.

13) Ensure that th e motors are pushed fully into the moun ting holes, then turn the

motors to be aligned as shown in Fig. 3.9. The left hand (X-Axis) motor connector

should point to the right hand side. The right hand (Y-Axis) connector should point

downwards. Check through the large open face that the mirror ali gnment is as

shown below.

Fig. 3.9 Aligning the motors

14) Using a 2 mm (5/64”) hex key, tighten the pinch bolts on the clamps as shown below.

Fig. 3.10 Tightening the pinch bolts

15) Using a 3 mm (1/8”) hex key, refit the blanking plugs.

16) The system is now ready to be m ounted into a cage system, however further

adjustment of the motor posi tions may be nece ssary to fine tune the mirror

alignment within the application.

Page 8 ETN032532-D02

GCM102(/M) 30 mm Cage System Mount for GVSx02 Series Galvos

3.2 Fitting the Optics and Adapters

A range optics can be fitted to the GCM102(/M) using various adapters as detailed

below.

Fig. 3.11 Fitting the LSM02

Optic Thread Scan

Distance

(mm)

Distancefrom

start of SM2

thread (mm) Adapter Required

LSM02 M25 x 0.75 16 3 GCMA1

LSM03 M25 x 0.75 19 6 GCMA1 (reverse fitted)

LSM04 M25 x 0.75 19 6 GCMA1 (reverse fitted)

LSM03-VIS M25 x 0.75 29 16 SM2A33 and SM2L03

LSM05 SM2 75 62 SM2L20

CLS-SL SM2 58 46 SM2L05 and SM2V05

Distance from

input axis to

reference face

of lens

11.0 mm (0.43”)

GCMA1

screwed down to

bottom face

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere THORLABS Messgerät Handbücher

THORLABS

THORLABS K10CR1 Bedienungsanleitung

THORLABS

THORLABS Blueline Series Bedienungsanleitung

THORLABS

THORLABS SA200 Series Bedienungsanleitung

THORLABS

THORLABS HRS015 Bedienungsanleitung

THORLABS

THORLABS PM160 Bedienungsanleitung

THORLABS

THORLABS PDA100A Bedienungsanleitung

THORLABS

THORLABS TLX3 Bedienungsanleitung

THORLABS

THORLABS HNL020R Bedienungsanleitung

THORLABS

THORLABS PM100USB Bedienungsanleitung

THORLABS

THORLABS PM100D Installationshandbuch

THORLABS

THORLABS VSD500 Bedienungsanleitung

THORLABS

THORLABS PM10-3 Bedienungsanleitung

THORLABS

THORLABS NST50 Bedienungsanleitung

THORLABS

THORLABS EDU-SPEB1 Bedienungsanleitung

THORLABS

THORLABS upLED Bedienungsanleitung

THORLABS

THORLABS PM200 Bedienungsanleitung

THORLABS

THORLABS S1 Series Bedienungsanleitung

THORLABS

THORLABS DC2100 Bedienungsanleitung

THORLABS

THORLABS CCS Series Bedienungsanleitung

THORLABS

THORLABS GSL Series Bedienungsanleitung

THORLABS

THORLABS EVOA1550F Bedienungsanleitung

THORLABS

THORLABS HRP350 Bedienungsanleitung

THORLABS

THORLABS PM102 Bedienungsanleitung

THORLABS

THORLABS CCS Series Gebrauchsanweisung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung