Tiger TI - 02 P Bedienungsanleitung

TI – 02 P

Weighing indicator

User’s Guide

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPT TO OPERATE THE INSTRUMENT

May 2015

Specifications subject to change without prior notice

CONTENTS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYS, DISPLAY AND CONNECTIONS

4. GETTING STARTED

5. INITIAL SETUP

6. INSTRUCTION FOR USE

7. RS232 DATA OUTPUT

8. BATTERY POWER AND RECHARGING

9. ERROR CODES

10. DAILY CARE AND MAINTENANCE

1. INSTALLATION

Because of metrological legislation, installation/some

metrological parameter settings are limited to be done by

authorized personnel only. Do not attempt to change any of the

built-in metrological parameters. Contact your dealer for more

information and technical assistance.

To ensure performance accuracy, do not use the instrument in

where or when the environment condition falls beyond as those

listed on SPECIFICATIONS.

Do not attempt to open the instrument, no user serviceable

parts inside.

2. SPECIFICATIONS

2.1 GENERAL SPECIFICATIONS

Maximum Capacity

Single Range Mode:-

Max = 1 ~ 999,999 (kg or lb)

Dual Range Mode: -

Max1 = 1 ~ 999,998( kg or lb)



Max2 = 2 ~ 999,999( kg or lb)

External Resolution

Single Range Mode:-

Recommend = 15,000 ~ 30,000

High = 30,000 ~ 60,000

Dual Range Mode: -

Recommend (Max2/ d1) = 15,000 ~ 30,000



High (Max

/ d

) = 30,000 ~ 60,000

Weight Units

Metric (kg) and Imperial (lb),g,oz

Min. Internal Count/d

15 Count

Offset Range

≥0.2mv (10000 Count)

Tare Range

- Max (Subtractive Tare)

Max. Measuring Range

15 mV

A/D Sampling Speed

15 times/ second

Power Voltage

Requirements

Built-in Rechargeable Battery = 6V DC

External Power Adaptor = 12V DC, 800mA

Load Cell Excitation

Voltage

5 VDC

Minimum/Maximum

Load Cell Impedance

350Ω/1000Ω

Load Cell Connection Supports 4-wire and 6-wire Load Cell

Connections

Maximum Load Cell

Connection

8 x 350ΩLoad Cells, or

16 x 700ΩLoad Cells

Operation Environment

-10 ~ 40

C. Non-condensed. R.H.≦85%

Specifications subject to change prior to notice

3. KEYS, DISPLAY AND CONNECTIONS

1.CNT KEY

Press this key to enter counting function

Press this key as next parameter when setting

2. WEIGHT UNIT KEY

Press this key to shift among various weight units.

Press this key as previous parameter when setting

3. WEIGH KEY

Press this key to back weighing status after counting, checking, animal

weighing, percentage function

4. PRINT KEY

Press this key to print the results to a computer or a printer through the

RS-232 output. according to the parameter setting whether accumulate or

not when printing

5.TARE KEY

Press this key to tare off the weight of a container.

Press this key to enter parameter setting when self-checking after power on

Press this key to confirm the parameter option

CNT 2

UNIT 3

WEIGH CE

PRT 5

MC 6

CHK ZERO

ANI 8

PCENT 9

PTARE TARE

SET ON/

OFF

6. ZERO KEY

Press this key to set weight displayed to zero when an empty scale has

drifted away from a true zero reading.

Cancel or quit from the operations

6. CHECK KEY

Press this key to start check weighing function and to enter value for HI and

LO limit.

7. ANI KEY

Press this key to enter animal weighing function

8.PERCENTAGE KEY

Press this key to enter percentage weighing function

9.PTARE KEY

Press this key to enter pre-set tare value

10.MC KEY

Press this key to recall total stored transactions.

11.CE KEY

Press this key to clear value entered.

12. NUMERIC KEYS

Numeric keys 0 ~ 9 and decimal key.

13.ON/OFF

Power on /off the indicator

◆

LED VERSION(HE200P) AS BELOW

14. CHECK SYMBOLS

HI = Weight reading is higher than the HI limit entered,

OK = Weight reading is in between than the low and HI limits entered,

LO = Weight reading is lower than the LO limit entered.

15. TARE INDICATOR

Visible when the tare function is in effect. Weight reading shown is net value

16. STABLE INDICATOR

Visible when weight reading is stable.

17. ZERO INDICATOR

Visible when instrument is at true zero weight status.

18. WEIGHT UNIT

LED indication as below:

kg =”kg” on,lb = “lb” on

oz = both “kg” and “lb” on; g= neither “kg “ nor “lb” on

19.

CHARGE INDICATION

Flicker when charging ; invisible when full of charge

◆

LCD VERSION (HC200P) AS BELOW

14. CHECK SYMBOLS

HI = Weight reading is higher than the HI limit entered,

OK = Weight reading is in between than the low and HI limits entered,

LO = Weight reading is lower than the LO limit entered.

15. SPARE

W1/W2 ，if assigned , the scale are in dual range capacity status

Blank, no function assigned.

16. BATTERY POWER / LEVEL INDICATOR

Visible to show:-

This instrument is being powered by the built-in rechargeable battery,

Remaining battery level.

17. HOLD INDICATOR

(When under animal mode) Visible when weight reading being displayed is

a frozen value.

18. AUTO INDICATOR

Visible when the instrument is in animal weighing function.

19. NET INDICATOR

Visible when the tare function is in effect. Weight reading shown is net

value.

20. GROSS INDICATOR

Visible when gross weight reading is displayed.

21. STABLE INDICATOR

Visible when weight reading is stable.

22. ZERO INDICATOR

Visible when instrument is at true zero weight status.

23. CAPACITY TRACK BAR

The ratio (increment = 10%) of applied & remaining weighing capacities are

shown here.

24. WEIGHT UNITS AND FUNCTIONS

% = Percentage (when in Percentage Mode in function),

kg = kilogram,

PCS = Pieces (Piece Count Mode in function),

kg/PCS and g/PCS = Weight per piece (when Piece Count Mode in

function),

lb = pound.

BACKSIDE INSTRUCTION

The recommend (from left to right):

1) power plug

2) Load cell

LOAD CELL

CONNECTOR PIN #

ASSIGNMENT

EXCITATION +ve

SENSE +ve

EXCITATION -ve

SENSE -ve

SIGNAL +ve

SIGNAL -ve

GROUND

3) Com1 RS232

RS232 COMPORT ON

INSTRUMENT

1 = GND

2 = TXD

3= RXD

IF USE CABLE

GLANDS,LOADCELL AND

RS232 CABLE NEED TO GO

THROUGH GLANDS TO

CONNECT ON THE PCB.

FOLLOW THE RIGHT POSITION

SIGN OF CONNECTION

PRINTED ON PCB

4. GETTING STARTED

In order to obtain an accurate weighing result, the weighing platform,

(hereinafter referred as platform) must be placed on a strong and level

surface. Avoid using the platform and this instrument (hereinafter

collectively referred as scale) in environment where excessive wind flow,

vibration and extreme temperature change exist

General Warning: -

The instrument is not an explosion proof device.

Do not open the instrument, no user serviceable parts inside.

Always contact your dealer for service.

The instrument not to be subject to shock, excessive vibration

or extremes of temperature (before or after installation).

4.1 BUILT-IN RECHARGEABLE BATTERY

The instrument is equipped with a built-in rechargeable battery. Before first

time use, recharge it for at least 8 hours to ensure the best battery

performance.

4.2 POWER ADAPTOR

Before plugging in the power adaptor, check and make sure the input

voltage of the adaptor matches with output voltage of the electricity outlet. If

not, contact your dealer immediately.

4.3 CONNECTING OTHER DEVICES1

4.3.1 Connection with Weighing Platform (Load Cell)

Connect this instrument with a weighing platform (load cell) through load

cell connector located at the back according to the assignment table.

4.3.2. Connecting RS232 to computer, printer

Inhaltsverzeichnis

Andere Tiger Messgerät Handbücher

Tiger

Tiger TTA-01 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung