tigerlight SL160 Bedienungsanleitung
Drawings herein for SL160 are used as examples.
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
IMPORTANT INSTALLATION INFORMATION
1.Normal operating environment and temperature: -40℃-+50℃.
Fixtures is suitable for Airport, Car Dealerships, Achitectural,
Factory, Warehouse, High Mast lighting and stadium lighting.
2.Before commencing installation or maintenance, ensure electricity
is switc hed off at the mains. Installation or maintenance should be
carried out by a qualified electrician.
3.The luminaire must not, under any circumstances, be installed
directly to flammable materials, and luminaires must not be
covered with any flammable materials.
4.Mounting height range of 6 to 12 meters, this model is suitable
for outdoor lighting.
5.Ensure there is adequate free air circulation of at least 50cm
around the luminaire. All luminaires run hot. It is the installer's
responsibility to consider fire risk and take appropriate precautions.
Installation Instruction & Installation Steps
1 2
3 4
STEP 1:
Use a 6mm hex wrench to loosen the screws that secure the lamp
post above the lamp arm, then slide fixture on to pole through
opening on the rear of housing. See Figure 1.
STEP 2:
Ensure to slide fixture to the inner end of tenon, then tighten
locking bolts with 5mm hex wrenc h or its equivalent to ensure the
fixture is fixed to polefirmly.
See Figure 2.
STEP 3:
1.Loosen hinged hatch locking bolts with 5mm hex wrench or its
equivalent, and open the hatch for led driver compartment access.
2.Get mains power supply cord into led driver compartment via
cable gland, Install power connections as per Figure 6, and lock
the gland to mains power supply cord tightly.
STEP 4:
1.Referring to Fig. 4, use a wrenc h loosen Screw by 3-5 threads to
adjust the fixtures angle. Once angle is decided, secure the hex
screw with 25 n.m of force.
2.Using the in-built bubble level, align fixture to the horizontal plane.
Adjust screws accordingly. Once leveled use 45 n.m to secure the
fixture to the light pol e . Ensure that the fixture is now attached to
the light pole securely. Close the cover and secure the cover screws
with 25 n.m of force.
W H
L
Locking bolts
Pole
Hinged hatc h
locking bolts
Cover
Mains power
supply cord
Cable gland Screws to adjust and lock rotatable tenon
415V High Voltage LED Street Light
INSTALLATION INSTRUCTION
LED Street Light
INSTALLATION INSTRUCTION
7 8
STEP 1:
Remove the two fixing bolts from the fixture as shown in Figure 7,
then take out the slip fitter.
Slip fitter
Screws
STEP 2:
Rotate the slip fitter as shown in Figure 8 and slide the slip-fitter
back into position, use 25 n.m torque to tighten the screws.
Pole-arm(Horozontal Tenon)Mounting Pole Top Mounting
-5°
+15°
+15°
-5°
Adjustable Slip Fitter from Pole-Arm mounting to Pole-Top Mounting Steps
9
5
Photocell
PHOTOELECTRIC CONTROLLER INSTALLATION (OPTIONAL)
STEP A: Make sure a NEMA receptacle on top of fixture is available.
STEP B: Find out the size difference of three pins on P.E.C.U., the
size difference of three slots on NEMA receptacle.
STEP C: Insert P.E.C.U. in receptacle, and twist it clockwise
firmly.See Figure7.
PRECAUTIONS:
If the above receptacle is unscrewed, please be sure to note
that the receptacle screw torque
of 1.0 to 2.0 N-m is recommended. Do NOT exceed 3.0 N-m.
Install photocontrol or shorting plug , Downlight only.
This logo indicates that this product must not be disposed of with other waste.
Please recycle used lamps to prevent environmental hazard and threats to human
health resulting from improper disposal.
Rev. Date: V1 08/11/2020
www.tigerlight.com.au
The instruction is for reference only. All rights reserved by
Please visit our website www.tigerlight.com.au and download the electronic
version of instruction and specification sheet if needed.
Tiger Light Pty Ltd.
WIRING INSTRUCTION
STEP I: Connect the L1 wire in the mains power supply cord to the “L1”
marked hole In the terminal block and tighten the connection
properly.
STEP II: Connect the L2 wire in the mains power supply cord
to the “L2” marked hole in the terminal block and tighten the
connection properly.
STEP III: Connect the Earth wire in the mains power supply cord
to the “ ” marked hole in the terminal block and tighten the
connection properly.
6
Electrical Connections
Terminal Block
L1
L2
L1
Earth
L2
L1-Brown
Earth
L2-Blue
Mains power supply
LED Driver
Andere tigerlight Außenleuchte Handbücher
Beliebte Außenleuchte Handbücher anderer Marken
LIGMAN
LIGMAN BAMBOO 3 Bedienungsanleitung
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung
urban ambiance
urban ambiance UQL1273 Bedienungsanleitung
TotalPond
TotalPond 52238 Bedienungsanleitung
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Bedienungsanleitung