Timberwolf TPS35 Bedienungsanleitung

W415-0865 / B / 05.26.11

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.18B

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.timberwolfﬁreplaces.com • ask@timberwolfﬁreplaces.com

$10.00

SAFETY INFORMATION

!WARNING

PLEASE READ ENTIRE MANUAL

BEFORE YOU INSTALL OR USE THIS

PELLET BURNING APPLIANCE.

If the appliance is not properly installed,

a house ﬁre may result causing personal

injury or loss of life.

- Authorities having jurisdiction (such as

municipal building department, ﬁre department,

ﬁre prevention bureau, etc.) should be consulted

before installation to determine the need to obtain

a permit.

- Contact local building or ﬁre ofﬁcials about

restrictions and installation inspection

requirements in your area.

- This appliance is hot while in operation. Keep

children, clothing and furniture away. Contact may

cause skin burns.

- Do not start a ﬁre with chemicals or ﬂuids such

as gasoline, engine oil, etc...

CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.

This appliance has been tested to ASTM E 1509, ULC/ORD C1482M-90, ULC S627 AND ULC S628.

TPS35

PELLET STOVE

TPI35

PELLET INSERT

W415-0865 / B / 05.26.11

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

1.1 STOVE 3

1.2 INSERT 4

2.0 INTRODUCTION 5

2.1 DIMENSIONS 6

2.1.1 STOVE 6

2.1.2 INSERT (COMPLETE WITH FLASHING) 6

2.2 SPECIFICATIONS 7

2.3 GENERAL INSTRUCTIONS 7

2.4 GENERAL INFORMATION 8

2.4.1 FUEL 8

2.4.2 PELLET SPECIFICATIONS 9

2.4.3 CORN SPECIFICATIONS 9

2.4.4 SAFETY FEATURES 10

2.4.5 EPA COMPLIANCE 10

2.5 RATING PLATE INFORMATION 10

3.0 INSTALLATION PLANNING 11

3.1 INSTALLATION OPTIONS 11

3.2 APPLIANCE PLACEMENT 11

3.3 MINIMUM CLEARANCE TO COMBUSTIBLES 12

3.3.1 STRAIGHT INSTALLATION 12

3.3.2 CORNER INSTALLATION 12

3.4 FLOOR PROTECTION REQUIREMENTS INSTALLATION 13

3.5 OUTSIDE AIR 13

3.6 MOBILE HOME 13

4.0 VENTING 14

4.1 TYPE OF VENT 14

4.2 INSTALLING THE PELLET VENT 14

4.3 VENTING THE PELLET APPLIANCE 14

4.4 PELLET VENT TERMINATION 15

4.5 VENT TERMINAL CLEARANCES 15

4.6 STOVE VENTING INSTALLATION EXAMPLES 16

4.6.1 HORIZONTAL TERMINATION (THROUGH WALL) 16

4.6.2 VERTICAL RISE HORIZONTAL TERMINATION (THROUGH WALL) 16

4.6.3 VERTICAL TERMINATION 17

4.6.4 CLASS A CHIMNEY RETROFIT 17

4.6.5 HEARTH MOUNT INSTALLATION 18

4.7 INSERT VENTING INSTALLATION EXAMPLES 19

4.7.1 TYPICAL EXISTING MASONRY INSTALLATION 19

4.7.2 FACTORY BUILT FIREPLACE 20

5.0 FRAMING (INSERT ONLY) 21

5.1 INSTALLATION INTO A COMBUSTIBLE ENCLOSURE 22

5.2 MINIMUM ENCLOSURE CLEARANCES 23

5.3 MINIMUM CLEARANCE TO COMBUSTIBLES 23

5.4 MINIMUM MANTEL CLEARANCES 24

5.5 ALCOVE INSTALLATION REQUIREMENTS (MINIMUM) 24

6.0 FINISHING 25

6.1 INSTALLING VIEWING DOOR 25

6.2 DOOR HANDLE INSTALLATION 26

6.3 DECORATIVE INSET 26

6.4 FLASHING INSTALLATION 27

7.0 WIRING DIAGRAM 28

8.0 OPERATING INSTRUCTIONS 29

8.1 PROPER PELLET LOADING 29

8.2 PRE-START CHECK 29

8.3 LIGHTING APPLIANCE MANUALLY 29

8.4 LIGHTING INSTRUCTIONS 30

8.5 CONTROLS 30

8.6 CONTROL ADJUSTMENT 31

8.7 INSTALLING A THERMOSTAT 31

8.8 SHUTDOWN INSTRUCTIONS 31

9.0 NORMAL OPERATING SOUNDS 32

W415-0865 / B / 05.26.11

1.0 INSTALLATION OVERVIEW

Door, see “FINISHING - INSTALLING

THE VIEWING DOOR” section.

Venting, see “GENERAL VENTING”

and “INSTALLATION” sections.

Floor, see “INSTALLATION PLANNING -

FLOOR PROTECTION REQUIRE-

MENTS” section.

See “OUTSIDE AIR”

section.

Handle, see “DOOR

HANDLE INSTALLATION”

section.

Rating plate, see

“RATING PLATE

INFORMATION”

section.

1.1 STOVE

10.0 MAINTENANCE 33

10.1 DAILY (WHENEVER USING THE APPLIANCE) 33

10.1.1 DISPOSAL OF ASHES 33

10.1.2 INSPECT THE BURN POT 33

10.1.3 CARE OF GLASS 33

10.1.4 CLEANING THE HEAT EXCHANGER TUBES 34

10.1.5 MAKE SURE PELLETS ARE NOT PILING UP 34

10.1.6 CLEANING THE BURN POT 35

10.2 BI-WEEKLY (OR EVERY 10 BAGS OF PELLETS) 35

10.2.1 VACUUM FIREBOX 35

10.3 SEMI-ANNUALLY (OR EVERY TWO TONS OF PELLET) 36

10.3.1 VACUUM HOPPER 36

10.3.2 SOOT AND FLY ASH FORMATION 36

10.3.3 CLEAN THE VERTICAL EXHAUST DUCT 36

10.3.4 CLEAN THE EXHAUST BLOWER 37

10.3.5 CHECK ALL SEALS 37

10.3.6 CLEAN THE VENT 38

10.4 IN THE EVENT OF A JAMMED AUGER 38

11.0 REPLACEMENTS 39

12.0 TROUBLESHOOTING 41

13.0 WARRANTY 44

14.0 SERVICE HISTORY 45

W415-0865 / B / 05.26.11

1.2 INSERT

Door, see “FINISHING -

INSTALLING THE VIEW-

ING DOOR” section.

Venting, see “VENTING” and

“INSTALLATION” sections.

Handle, see “DOOR

HANDLE INSTALLATION”

section.

Rating plate, see

“RATING PLATE

INFORMATION”

section.

Flashing, see “FLASHING

INSTALLATION” section.

W415-0865 / B / 05.26.11

2.0 INTRODUCTION

3.8B

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to

operating instructions could cause ﬁre or injury. Contact the local building or ﬁre authority and follow their guidelines. Notify

your insurance company of this appliance as well.

• Never try to repair or replace any part of the appliance unless instructions are given in this manual. All other work should be

done by a trained technician.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not operate without fully assembling all components.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or

clothing ignition. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is rec-

ommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety

gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁc and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces.

These screens and guards must be fastened to the ﬂoor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance and venting

system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a quali-

ﬁed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The

appliance area must be kept clear and free from combustible materials, gasoline and other ﬂammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service technician to inspect the appli-

ance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a

licensed or qualiﬁed service person. The viewing door and ashpan must be closed and latched during operation.

• Do not strike or slam shut the appliance glass door.

• Only doors / optional fronts certiﬁed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags,

these are not toys and should be kept away from children and infants.

• If the appliance is not properly installed, a house ﬁre may result. Do not expose the appliance to the elements (ex. rain, etc.)

and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance is used.

• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.

• The heater is designed and approved for pelletized wood fuel only. Any other type of fuel burned in this heater will void the

warranty and safety listing.

• Do not start a ﬁre with chemicals or ﬂuids such as gasoline, engine oil, etc.

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away from the

home or structure.

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke spillage in

your home.

• The exhaust system must be completely straight and properly installed. It is recommended that the pellet vent joints be sealed

with a minimum 500°F (260°C) silicone sealant. Install according to the vent manufacturer’s instructions.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated

temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V.

or other electronic components.

• During a power outage this appliance will not operate. If a power outage does occur, check the appliance for smoke spillage

and open a window if any smoke spills into the room.

• Keep foreign objects out of the hopper.

• Disconnect the power cord before performing any maintenance. NOTE: Turning the pellet feed to “OFF” does not discon-

nect all power to the heater.

• Do not throw this manual away. This manual has important operating and maintenance instructions that you will need at a

later time. Always follow the instructions in this manual.

• At no point should you use ﬁrewood or ﬁrelogs in this appliance. The use of which could cause a house ﬁre.

• This appliance must be connected to a standard 115 V, 50Hz grounded electrical outlet. Do not use an adapter plug or sever

the grounding prong. Do not route the electrical cord underneath, in front of, or over the appliance.

• When installed in a mobile home, the appliance must be bolted to the ﬂoor, have outside air, and NOT BE INSTALLED IN THE

BEDROOM (per H.U.D. requirements). Check with local building ofﬁcials.

• The exhaust system should be checked and cleaned once a year minimum for any build-up of soot or creosote.

• This heater becomes very hot, you MUST wear heat resistant gloves when cleaning or handling this heater.

W415-0865 / B / 05.26.11

2.1 DIMENSIONS

11/16"

5/16"

1/4"

1/2"

1/4"

5/8"

7/8"

CENTRE LINE

OF AIR INTAKE

1/8"

3/8"

5/8"

1/2" CENTRE LINE

OF AIR INTAKE

CENTRE LINE

OF EXHAUST

1/4"

3/8"

13/16"

CENTRE

LINE OF

EXHAUST

CENTER LINE

OF INSERT

7/8"

3/8"

1/4"

CENTRE LINE

OF AIR INTAKE

CENTRE

LINE OF

EXHAUST

2.1.1 STOVE

2.1.2 INSERT (COMPLETE WITH FLASHING)

* A and B are adjustable, see "SPECIFICATIONS" section.

W415-0865 / B / 05.26.11

2.2 SPECIFICATIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE

WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA C22.1

CANADIAN ELECTRIC CODE (IN CANADA) OR THE ANSI/NFPA NO. 70 NATIONAL ELECTRIC CODE

IN THE UNITED STATES.

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. DO

NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE

FRONT FACE OF THE APPLIANCE.

WARNING

Adjuistable Flashing 11" to 13" 10 1/2" to 12 1/2"

Electrical Rating 115 Volts, 3.6 Amps, 60Hz

Watts During Ignition Sequence 400 (approximately)

Watts During Operation 180 (approximately)

Weight Stove 158 lbs / Insert 140 lbs

Exhaust Collar 3"

Intake Collar 2"

Hopper Capacity 45 Pounds

EPA Exempt

Burn Rate 1.5 to 4.5 (Pounds Per Hour)

BTU/H 12750 to 38250

Approximate Maximum Heating Capacity (in square feet)* 800 to 2000 Sq. Feet

Maximum Burn Time on Low Burn** 30 Hours

* Heating capacity will vary depending on the home's ﬂoor plan, degree of insulation, and the outside temperature. It is

also affected by the fuel size, quality, and moisture level.

** Small pellets will increase or decrease the stated burn rates and burn times. Differences of plus or minus 20% depend-

ing on fuel quality may occur.

2.3 GENERAL INSTRUCTIONS

W415-0865 / B / 05.26.11

2.4 GENERAL INFORMATION

Thank you for purchasing a Wolf Steel Ltd. Pellet Appliance. This appliance is designed for use with Pelletized

Wood Only.

Please read this entire manual before installation and use of this pellet fuel-burning room appliance. Failure to

follow these instructions could result in property damage, bodily injury or even death.

Keep this manual handy for future reference.

This Pellet Appliance, when installed, must be electrically grounded in accordance with the local codes, or in

the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA

70 National Electrical Code in the United States.

This appliance will not operate using natural draft or without a power source for the blower systems and fuel

feed system.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be

improved if the assembly is warmed, using a hair dryer or similar heat source.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood

ﬂooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

4.5

2.4.1 FUEL

This appliance is designed to burn wood pellet fuel. In addition, a corn/wood pellet mixture with a maximum

50% corn can be burned. Burning any other fuel, that is not approved for use with this appliance, will void the

warranty.

Important: The corn/wood pellet mixture needs to be mixed evenly before being put into the hopper.

W415-0865 / B / 05.26.11

If the fuel does not comply to

this standard the appliance may

not operate as designed.

We recommend the use of pre-

mium grade (1% ash content)

for longer appliance life and less

frequent cleaning.

Fines (ﬁne particles) 1% maximum through a 1/8" screen

Bulk Density 40 pound per cubic foot minimum

Size 1/4" to 5/16" diameter, 1/2" - 1 1/2" long maximum

Ash Content 1% maximum (Premium grade)

3% maximum (Standard grade)

Moisture Content 8% maximum

Heat Content Approximately 8200 BTU per pound minimum

2.4.2 PELLET SPECIFICATIONS

P.F.I. PELLET STANDARDS:

Pellet quality is important, please read the following:

Your Wolf Steel Ltd. Pellet Appliance has been designed to burn premium hard or soft wood pellets only. Do

not use any other type of fuel such as ﬁre logs or ﬁre starting pellets, as this will void the warranties stated in

this manual.

The performance and heat output of the pellet appliance is directly related to the quality and moisture of the

pellets. Store pellets in a cool dry area to prevent moisture absorption.

64.1

WARNING

IT IS IMPORTANT TO SELECT AND USE ONLY PELLETS THAT ARE DRY AND FREE OF DIRT OR ANY

IMPURITIES SUCH AS HIGH SALT CONTENT. DIRTY FUEL WILL ADVERSELY AFFECT THE OPERA-

TION AND PERFORMANCE OF THE APPLIANCE AND WILL VOID THE WARRANTY. THE PELLET

FUEL INSTITUTE (P.F.I.) HAS ESTABLISHED STANDARDS FOR WOOD PELLET MANUFACTURERS.

WE RECOMMEND THE USE OF PELLETS THAT MEET OR EXCEED THESE STANDARDS. ASK YOUR

DEALER FOR A RECOMMENDED PELLET TYPE.

2.4.3 CORN SPECIFICATIONS

Use only clean-shelled corn with a moisture content less than 15% and approximate fuel value of 7,000 BTU/

lb (16,200 kJ/kg). Do not attempt to burn corn with higher moisture content or burn lesser grade fuels. Do not

burn other types of agricultural pellets or by-products (alfalfa, cherry pits, olive pits, nut shells, etc.) as they are

not permitted to be burned in this appliance.

Corn must be clean and free of debris. Never burn corn right from the ﬁeld. Damage caused by dirty corn is

not covered by the Lifetime Limited Warranty. Ask for screened corn only. Stalk parts, excessive ﬁnes and

cob remnants will clog the air ﬂow holes in the burn plate. Check the corn for foreign objects.

Use only a maximum 50% corn to pellet mixture.

W415-0865 / B / 05.26.11

2.4.4 SAFETY FEATURES

2.4.5 EPA COMPLIANCE

This appliance is EPA exempt from Phase II

prerequisites, but complies with Oregon /

Washington emissions requirements.

We suggest that our pellet hearth

products be installed and serviced by

professionals who are certified in the U.S.

by the National Fireplace Institute

(NFI)

as NFI Pellet Specialists or who are

certified in Canada by

Wood Energy Technical

Training (WETT).

www.nficertified.org

66.1A

HIGH LIMIT SWITCH: Your appliance is equipped with a high limit switch. In the event that the temperature of

the appliance approaches an unsafe operating temperature, this switch will shut down the pellet feed, which

will eventually shut down the unit. If this happens, it is important to ﬁnd out why the unit overheated. Contact

your local dealer.

LOW LIMIT SWITCH: This switch will automatically shut down the appliance if the ﬁre goes out or fails to light

within 15 minutes.

HOPPER DOOR INTERLOCK: Your appliance is equipped with a micro switch in the hopper assembly that

shuts-off the auger when the hopper door is opened. Closing the door switches the auger back on, allowing

pellets to feed again.

VACUUM SWITCH: This switch will sense lack of air ﬂow through the appliance and shut down the pellet feed.

This lack of ﬂow could be caused by a blocked vent.

POWER FAILURE: In the event of a power failure, the appliance will shut down. Once power is restored, the

appliance will re-start, unless the convection air temperature has gone above the high limit switch setting. If

this happens, contact your local dealer.

2.5 RATING PLATE INFORMATION

CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITUREAWAY. CONTACT MAY CAUSE SKIN BURNS. U.S. ENVIROMENTAL PROTECTION AGENCY Certified to comply with July 1992 Particulate Emission Standards

MODEL TPS35 LISTED PELLET FUEL BURNING ROOM HEATER TESTED TO:

ASTM E 1509, ULC/ORD C1482-M90, ULC S627

TPS35

Straight Installation Corner Installation

MINIMUM CLEARANCES TO COMBUSTIBLE

SIDE 6”

REAR 3”

CORNER 2”

CEILING 48”

INPUT RATING

MIN 1.5 LB/HR

MAX 4.5 LB/HR

ELECTRICAL RATING

120V 3.6A 60HZ

Floor

Protection

Through

Wall

Installation

3”

6”

- INSTALLAND USE ONLY IN ACCORDANCE WITH THE

MANUFACTURER’S INSTRUCTIONS AND LOCAL

BUILDING CODES.

- MINIMUM CEILING HEIGHT: 7FT (2.13M) HEARTH

EXTENSION / COMBUSTIBLE FLOOR PROTECTION: IF

INSTALLED ON A COMBUSTIBLE FLOOR, UNIT MUST BE

PLACED ON A NON-COMBUSTIBLE FLOOR PROTECTOR

EXTENDING 6” IN FRONT.

- DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE

SERVING ANOTHER APPLIANCE.

- REPLACE GLASS WITH ONLY CERAMIC GLASS.

DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT

POWER BEFORE SERVICING UNIT.

- KEEP VIEWING AND ASH REMOVAL DOORS TIGHTLY

CLOSED DURING OPERATION.

- CONTACT LOCAL BUILDING AND FIRE OFFICIALS ABOUT

RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR

LOCAL AREA.

- SUITABLE FOR USE IN MOBILE HOMES WHEN USED WITH

OUTSIDE AIR INSTALLATION KIT.

- REFER TO INSTALLATION INSTRUCTIONS OR LOCAL

BUILDING CODES WHEN PASSING EXHAUST SYSTEM

THROUGH COMBUSTIBLE WALL OR CEILING.

-FUEL: FOR USE WITH PELLET FUEL ONLY.

Floor Protection

6”

2”

Floor Protection

6”

Interior

Vertical

Vent

2”

Tee

WOLFSTEELLTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

ATTENTION : L'APPAREIL EST CHAUD LORSQU’IL FONCTIONNE. NE PAS

TOUCHER. TENIR LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES À

L’ÉCART. LE CONTACT PEUT CAUSER DES BRÛLURES DE PEAU.

Certifié conforme à la norme d'émanation de particules de juillet 1992 du U.S. ENVIROMENTAL PROTECTION AGENCY

W385-0509 / B

- INSTALLER ET UTILISER CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET

AUX CODES DU BÂTIMENT LOCAUX.

- HAUTEUR DE PLAFOND MINIMALE 7 PI. (2,13 m)

BASE DE PROTECTION/PROTECTION DE PLANCHER COMBUSTIBLE : SI INSTALLÉ

SUR UN PLANCHER COMBUSTIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE

PLAQUE PROTECTRICE INCOMBUSTIBLE S’ÉTENDANT SUR 6” À L’AVANT.

- NE PAS RACCORDER CETAPPAREIL À LA CHEMINÉE D’UN AUTRE APPAREIL.

- REMPLACER LA VITRE PAR UNE VITRE EN CÉRAMIQUE SEULEMENT.

DANGER : RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANCHER L’ALIMENTATION

ÉLECTRIQUE AVANT DE PROCÉDER À L’ENTRETIEN.

- GARDER LA PORTE VITRÉE ET LA PORTE DU TIROIR À CENDRES BIEN FERMÉES

DURANT LE FONCTIONNEMENT.

- CONTACTER LES AUTORITÉS LOCALES DU BÂTIMENT ET DU SERVICE DES

INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS D’INSTALLATION

DANS VOTRE RÉGION.

- PEUT ÊTRE INSTALLÉ DANS UNE MAISON MOBILE SI INSTALLÉ CONJOINTEMENT

AVEC UNE PRISE D’AIR EXTÉRIEUR.

- SE RÉFÉRER AUX INSTRUCTIONS D’INSTALLATION OU AUX CODES DU BÂTIMENT

LOCAUX LORSQUE LE SYSTÈME D’ÉVACUATION TRAVERSE UN MUR OU UN

PLAFOND COMBUSTIBLES.

-COMBUSTIBLE : POUR USAGE AVEC DES GRANULES SEULEMENT.

Installation droite Installation de coin

MODÈLE TPS35 APPAREIL DE CHAUFFAGE AUX GRANULES HOMOLOGUÉ TESTÉ SELON LES

NORMES : ASTM E 1509, ULC/ORD1482-M90, ULC S627

DÉGAGEMENTS MINIMAUX AUX MATÉRIAUX COMBUSTIBLES

CÔTÉ 6”

ARRIÈRE 3”

COIN 2”

PLAFOND 48”

IDÉBIT D’ALIMENTATION

MIN. 1.5 LB/H

MAX. 4.5 LB/H

CARACTÉRISTIQUES ÉLECTRIQUES

120 V 60 Hz

3”

2”

Tee

Interior

Vertical

Vent

DATE CODE / DE DATE

6”

Floor

Protection

6” 6”

Protection de

plancher

Installations

à travers le

mur

Protection de

plancher

Évents à

travers le

mur

Coude

45°

Té

Protection de

plancher

Évents

verticaux

intérieurst

Protection de

plancher

Évents

verticaux

intérieurs Té

6”

45°

2”

6”

2”

3”

2”

6”

6” 6”

9700539 (WSL)

4001657 (NGZ)

4001658 (NAC)

4001659 (WUSA)

REFERENCE

#16544

Stove rating plate illustrated

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

SAMPLE

S. ENVIROMENTAL PROTECTION AGENCY C. ENVIROMENTAL PROTECT

RNING ROOM HEATERRNING ROOM HEAT

D C1482-M90, ULC S627D C1482-M90, ULC S627

MPLE

TPS

Corner Ins

Corner In

EARANCES TO COMBUSTIBLEEARANCES TO COMBUST

6”

3”

NER 2”2”

ILING 48”LING 48”

6”6”

ON, L4M 0G8 CANADAON, L4M 0G8 CANADA

AUD LORSQU’IL FONCTIONNE. NE PASAUD LORSQU’IL FONCTIONNE. NE P

LES VÊTEMENTS ET LES MEUBLES ÀLES VÊTEMENTS ET LES MEUBLES

AUSER DES BRÛLURES DE PEAU.AUSER DES BRÛLURES DE PEAU.

TATIONN

EN FERMÉES

ERVICE DESRVICE D

ONS D’INSTALLATIONONS D’INSTALLAT

STALLÉ CONJOINTEMENTLLÉ CONJOINTEMENT

OU AUX CODES DU BÂTIMENTODES DU BÂTIMENT

TRAVERSE UN MUR OU UNN MUR OU

RANULES SEULEMENT.ULES SEULEMENT.

Installation droitInstallation droi

MODÈLE TPS35 APPAREIL DE CHAUMODÈLE TPS35 APPAREIL DE

NORMES : ASNORMES : A

AMP

PLE

6”6”

Floo

Prot

Protection de

anc

plancher

Installations

travers le

à travers le

rmur

Andere Handbücher für TPS35

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Timberwolf Pelletofen Handbücher

Timberwolf

Timberwolf TPSI35 Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung