Top Flight Models P-47 THUNDERBOLT Bedienungsanleitung
© 1976 - TOP FLITE MODELS, INC.
Building the
P-47 THUNDERBOLT
Congratulations!
You now own the most accurate R/C Stand-Off Scale kit ever produced.
We at Top Flite hope that you will find this model the most pleasant to build,
inspiring to look at and exciting to fly that you have constructed.
It is honest to point out, however, that while this model is no more difficult - in
fact is simpler than most comparable kits to make, R/C Scale models generally are not
for the newcomer to this hobby. Previous modeling experience and careful attention to
craftsmanship are necessary. Even the "old hand" will do well to study and follow the
instructions and guidance given in this booklet.
It is our aim to have you say: "This is the finest model I have ever built."
TOP FLITE MODELS, INC.
ACKNOWLEDGEMENTS
The staff of Top Flite wishes to acknowledge the assistance of the following
individuals who contributed their time and talent to the successful creation of this kit:
Col. JIM G1LHULY (USAF RET.)
ART SCHROEDER
ART SAB1N
CLARK MACOMBER
Top Flite Models, Inc.
WARNING
A RADIO CONTROLLED MODEL IS NOT A "TOY". CARE AND CAUTION
MUST BE TAKEN IN PROPERLY BUILDING THE MODEL AS WELL AS IN THE
INSTALLATION AND USE OF THE RADIO CONTROL DEVICE. IT IS IMPORTANT
TO FOLLOW ALL DIRECTIONS AS TO CONSTRUCTION OF THIS KIT AS WELL AS
INSTALLATION AND USE OF THE ENGINE AND RADIO GEAR. THE ADVICE AND
ASSISTANCE OF A WELL-EXPERIENCED BUILDER AND PILOT ARE ESSENTIAL.
DON'T TAKE CHANCES. IMPROPER BUILDING, OPERATION OR FLYING OF THIS
MODEL MAY RESULT IN SERIOUS BODILY INJURY TO OTHERS, TO YOURSELF
OR PROPERTY DAMAGE.
THE P-47 STORY
The P47 was produced in larger numbers than any other U.S. Fighter of WWII.
15,683 production versions ranged from the P47-B, C, D, E, F, G, H, J, M, and N. Some-
what overshadowed by the publicity accorded the "Mustang" and the "Spitfire", the
"Thunderbolt" was, nonetheless a most distinguished and respected aircraft by friend and
foe alike.
The first P47 was test flown in May, 1941 and was known as the XP-47B. This air-
craft was designed to fill the need for a fighter aircraft able to exceed the anticipated ceilings
of enemy bombers, out gun them offensively; to escort and provide cover for American
bombers flying in the Substratosphere, and to out-gun enemy interceptors.
The first production models were assigned to fighter units in England where it be-
came extremely popular with AAF Pilots because of its ability to absorb extensive battle
damage and still remain flying.
Perhaps the most outstanding tribute to this aircraft is the fact that all ten of the
leading Thunderbolt "Aces" survived the war. Colonel Glenn T. Eagleston was one of these.
This kit is the P47D-25-RE version flown by Colonel Eagleston while a member of the
35rd Sq, 354th Gp, 19th Tactical Air Force commanded by General O.P. Weyland.
Col. Eagleston was the top "Ace" of the ninth Air Force, credited with 23'/2 destroyed, 2
probables and 7 damaged enemy aircrafts. It is to Colonel Eagleston that this kit is re-
spectfully dedicated.
References: Aero Publishers, Inc. Camouflage & Markings
329 Aviation Road Ducemus Books, Ltd.
Fallbrook, California London, England
Thunderbolt in Action U.S. Army & Air Force Markings, 1916-1961
3461 E. Ten Mile Road Library ofCongress Card No. 61-16739
Warren, Michigan 48091
CONSTRUCTION OF P-47
BEFORE YOU START, READ THIS:
The assembly sequence of your Top Flite P47 has been carefully developed to help
assure the correct alignment of your model. Utilize the check-off blocks as you build;
this will allow assembly of your model in minimum time.
Before beginning an assembly step, read the instructions to familiarize yourself with
the parts to be used. Find the parts mentioned and double check them for proper identifi-
cation and size with the plans. Do nut separate parts from the die cut sheets until you need
them. There are machined parts in your kit which are not identified, such as the fuselage
siders, stab, ailerons, etc. These parts can be easily identified by checking the parts against
the plans.
We are sometimes asked which glues are best for model construction. The answer to
this depends upon the particular job. This is our normal recommendation: For all
hardwood-to-hardwoud or hardwood-to-balsa joints, use white wood glue. "Titebond" is
especially good, as it dries faster than other white glues and is very strong. For balsa-to-
balsa joints, regular balsa-wood cements are ample for the job, although white glue can be
used here too. Whichever type you use, remember that excess glue is no substitute for a
well-fitting joint. Use a minimum of glue at all times, and wipe off excess glue that squeezes
out of joints before it sets hard; when set it is difficult to remove, but if not removed it
could spoil the covering job.
1
CONSTRUCTION
SEQUENCE
Follow each step in order and put
check marks in the blocks as you
complete each phase described.
FUSELAGE
1/4" x 1/2" NOTCHED STRIPS
2
Glue 1/4 x 1/2 notched balsa strips to fuselage sides. Make a
right and left side. Note: Curve on top edge of fuselage sides is
intentional.
Glue ply braces F-31 to fuselage sides. (See plans for position)
Glue hardwood wing screw blocks in place.
1
FIG.
1
RIGHT
FUSELAGE SIDE
LEFT FUSELAGE SIDE
F-31
(PLY)
HARDWOOD
WING SCREW BLOCK
F-31
(PLY)
NOTE CURVED TOP EDGE
NOTCHED STRIPS
STEP
HARDWOOD MOTOR MOUNTS
FIG.
2
3
3
Using bottom view of plans, cut 1/4 SQ. bulkhead spacers from
1/4 x 1/4 x 36 balsa strips.
Glue MOTOR MOUNT ASSEMBLY to fuselage sides over
bottom view of plans.
Starting with bulkhead spacer for F-8, glue and pin spacers in
place, working toward rear.
Glue F-17 (ply) in place. (Check plans for position). Hold
fuselage sides together with tape if necessary.
Trim rear, glue, and clamp together.
STEP
FIG.
3
FUSELAGE SIDE
TRIM TO 1/8" EACH
SIDE, GLUE, AND
CLAMP TOGETHER
BULKHEAD SPACER
FOR
F-8
MOTOR MOUNT
ASSEMBLY
1/4" SQ. SPACERS
F-17
(PLY)
FUSELAGE
Glue F-3A and F-3B together.
Pin F-5 spacers over bottom view of plans BETWEEN F-3AB
and F-7.
Glue motor mounts to the two F-5's.
Glue F-3AB assembly and F-7 (ply) vertical in position.
STEP
2
FUSELAGE
F-3B
F-5
F-7
(PLY)
USE TRIANGLEOR
SQUARE TO CHECK
ALIGNMENT.
F-5SPACERS
4
Cut two 1/4 SQ. strips to 15" and glue on top of notched strips
flush with the inside edge. Refer to fuselage cross SECTION B-B.
Using pattern on plans, cut 2 cardboard cooling tubes to size
and glue in place.
FUSELAGE
1/4" x 1/2" BACKBONE.
Glue bulkheads F-19, F-20, F-22, F-24, and F-26 in place.
Note angle of F-19 on plans.
Fit and cut 1/4 x 1/2 backbones to length and glue in place.
FIG.
4
CARDBOARD
COOLING TUBES
1/4" x 15" SO. STRIPS
15"
FUSELAGE
STEP
4
1/4"
x
1/2"
BACKBONE
F-19
F20
F-22
F-24
F
26
FIG.
5
STEP
5
GENERAL INSTRUCTIONS
5
TRIM OFF HERE
BOTTOM EDGE
TRIM OFF HERE
CUT ALONG CENTER
BOTTOM EDGE
HOLD IN PLACE WITH TAPE
Extensive effort has gone into the development of the shells
provided in this kit. Occasionally one shell may split or crack due
to rough treatment during shipment. If this occurs it can easily
be repaired with glue. Each shell is purposely oversize. This is to
allow you enough wood to work with and attain a perfect fit.
When fitting, cut small portions at a time. Trim the shells as in
FIG.
6.
When fitting a shell, lay it lengthwise on it's BOTTOM EDGE.
If it is not flush, sand it until it is. Tape or pin it in place and
cut along the top center. Do the same with the opposite side.
When both shells fit properly, glue them in place. Masking tape
works well in holding them while drying.
FITTING SHELLS
CENTER EDGE
BOTTOM EDGE
TOP SHELL
CENTER EDGE
BOTTOM SHELL
FIG.
6
FIG.
7
6
Cut and fit the REAR SECTIONS and glue in place.
Glue the tail blocks in place.
Trim and fit forward shell sections. DON'T GLUE IN PLACE
YET.
Glue F-13R and F-13L together.
Glue F-11 to bottom part of F-9.
Glue F-15 to bottom part of F-16.
Glue F-13R L assembly on top edges of F-11 and F-15.
Glue F-10 and F-14 on top of F-13 RL.
Glue F-12 2" behind F-10.
FUSELAGE
HARDWOOD
TAIL
BLOCK
BALSA
TAIL
BLOCK
F-26
REAR SECTION
p-19
F-7
F-3AB
FIG.
8
SET CENTER SECTION ASIDE
FORWARD SHELL SECTION
STEP
6
FUSELAGE
COCKPIT
ASSEMBLY
P-12
F-14
F-13R F-13L
F-10
F-15
2"
F-11
FIG.
9
STEP
7
P-9
7
FUSELAGE
1/4" x 1/2" BACKBONES. COCKPIT ASSEMBLY
1/4"
x
1/4"
x 33-1/2"
STRIPS
F25
F-23
F-8
F6
F-2
F-4
F21
F-18
NOTCH STRIP
TRIM REAR
OF F-27'S
TO
1/4"
THICKNESS
F27
FIG.
10
Glue F-27'S to rear of fuselage.
Cut and glue 1/4 x 1/4 x 33-1/2 strips to inside half of
NOTCHED STRIPS. See fus cross section A-A.
Glue COCKPIT ASSEMBLY in place.
Glue bulkheads F-2 thru F-25 in place.
Cut and glue 1/4x1/2 backbones in place.
STEP
8
FUSELAGE
TOPRIGHT
FUSELAGE SHELL
TOPLEFT
FUSELAGE SHELL
FIG.
11
Trim, fit, and glue top fuselage shells in place.
STEP
9
3/32" x 4" x 30" BALSA SHEETS
FIG.12
Join three 3/32 x 4 x 30 balsa sheets using masking tape as
shown.
Turn over and glue joints as shown.
Pin to a flat surface and allow to dry.
Remove tape.
Make 4 SETS of panels.
8
FIG.
13
Glue balsa half rib W-2A to RIB W-2.
Glue landing gear brace W-13 (PLY) to ribs W-3 and W-5
Make sets for RIGHT WING half and LEFT WING half.
STEP
2
W-2
W-2A
W-5
W-3
PLY
W-13
WING
STEP
1
WING
Inhaltsverzeichnis
Andere Top Flight Models Spielzeug Handbücher
