Topcon Athene SM-1 Bedienungsanleitung

www.topconpositioning.com

Athene SM-1 Spreader Control

Operator’s Manual

Athene SM-1 Spreader Controller

Operator Manual

Part Number: 1014197-01

Rev Number: 5

For use with Horizon Software Version 5.02

Athene Software Version 3.20

January 2022

contained herein may not be used, accessed, copied, stored, displayed, sold, modified,

published or distributed, or otherwise reproduced without express written consent from

Topcon.

This manual provides information about operating and maintaining this

Topcon Precision Agriculture product. Correct use and servicing is

important for safe and reliable operation of the product.

It is very important that you take the time to read this manual before

using the product.

Information in this manual is current at the time of publication. A system

may vary slightly. The manufacturer reserves the right to redesign and

change the system as necessary without notification.

Technical documentation and utility software

On the myTopcon NOW! support website

(mytopconnow.topconpositioning.com) or myTopcon NOW! app you

can access the following support material:

lFirmware and software updates

lProduct manuals

lProduct quick guides

lTraining videos

lSystem layouts

iii

Table of contents

Chapter 1 – Introduction 1

Chapter 2 – Topcon X-Console Implement Setup 3

2.1. Switching between setup and operation screen 3

2.2. Enabling ISOBUS 4

2.3. Setting up a new vehicle 7

2.4. Selecting an implement 9

2.5. Setting implement geometry 13

2.6. Setting up section control 15

2.6.1. Enabling section control 15

2.6.2. Setting up the section switch 15

2.7. Setting up speed 16

2.8. Opening the Athene UT window 17

Chapter 3 – Athene Setup 19

3.1. Athene primary screens 19

3.1.1. Main screen 19

3.1.2. Spreader settings screen 24

3.1.3. Totals screen 39

3.2. Setting up units 43

3.3. Load cell configuration 44

3.3.1. Can Module 1 configuration 44

3.3.2. Scale Link configuration 46

3.3.3. Load cell calibration 48

3.4. Setting up working width 49

3.4.1. Offsets explanation 49

3.4.2. Setting on and off time 50

3.5. Setting up pre-start 51

3.5.1. Operating pre-start 52

3.6. Setting up border reduction 53

3.6.1. Operating border reduction 54

3.7. Setting up products 55

3.8. Setting up alarms 57

3.9. Setting up forward speed 58

3.9.1. SSF Autocal 58

3.9.2. Simulated speed 59

3.10. Adding product / tare 60

3.10.1. With load cells 60

3.10.2. Without load cells 60

Chapter 4 – Calibration 62

4.1. Product calibration modes 62

4.2. Volumetric calibration (machines without load cells) 64

4.3. Dynamic mode calibration 66

4.3.1. Product flow factor – check calibration routine 68

4.4. Nudge calibration 71

4.5. Valve calibration 72

Chapter 5 – Updating Athene Software 74

5.1. Saving and loading factors 76

5.1.1. To save factors 76

5.1.2. To load factors 76

Chapter 6 – Operation with Topcon Console 78

6.1. Opening auto section control 78

6.2. Variable rate control 80

6.2.1. Source options 81

Chapter 7 – How Dynamic Calibration Works 85

Chapter 8 – Machine Setup Checklist 90

Chapter 9 – Index 91

Chapter 10 – Regulatory and Safety Warnings 92

10.1. Topcon Positioning Systems, Inc. End User License Agreement 101

Chapter 1 – Introduction

The Athene spreader controller is an ISOBUS UT-compliant monitoring

and application control system for self-propelled / trailed belt spreaders

spreading lime / granular materials. Forward speed measurement and

cutout sensing enables full proportional control, to maintain (within

limits) a set application irrespective of changes in forward speed.

Shown is a typical retrofitted system (that is independent from the

tractor ISOBUS), utilizing a Topcon X-Console. In this scenario, refer to

Topcon X-Console Implement Setup, page 3 for console setup

instructions.

Some installations will have minor variations, but the key components

are the console, spreader ECU, load cell ECU and load cells. The

system is compatible with an ISOBUS UT compliant tractor terminal. If

using a non-Topcon terminal through ISOBUS, refer to the

manufacturer's manual for setup of the terminal and go to Athene

Setup, page 19 for instructions.

Forward speed sensing may be performed via GPS, or optionally by a

magnetic sensor measuring wheel or propshaft rotation (fitted to the

tractor / self-propelled spreader or trailed spreader). The master on/off

switch is ‘virtual’ (a softkey on the Athene operation screen), or

optionally via an external switch mounted next to the operator.

The system may be fitted with or without load cells.

Machines without load cells: The system relies on volumetric calculation

from the known gate height and width, and a known product density. It

works best with relatively free-flowing material of consistent density.

Machines with load cells: Load cells enable fully-automatic, continuous

calibration. They are advantageous for controlling the rate of material

with more variable density at higher rates. By constantly measuring the

weight of product in the spreader, the floor (belt) speed is continuously

adjusted to achieve the correct target application rate. The system

quickly reacts to changes in product characteristics or spreading

conditions without having to adjust or re-calibrate the machine. This

works best with higher rates where weight changes are significant.

Other spreader functions, such as spinner speed, can also be

monitored or controlled, with warnings being triggered if they are not

operating correctly.

Chapter 2 – Topcon X-Console Implement

Setup

This chapter explains how to setup and configure the Topcon console

for use with the Spreader Controller features.

Note: If you are using a non-Topcon ISOBUS terminal, go to Athene

Setup, page 19 for instructions.

2.1. Switching between setup and operation

screen

The console has two main screens; the Setup screen and the Operation

screen.

Use the highlighted buttons to switch between the screens.

2.2. Enabling ISOBUS

Enables the ISOBUS Universal Terminal server that allows interaction

with the Athene ISOBUS compliant ECU.

To enable ISOBUS / Universal Terminal:

1. Select System /Features /Console .

2. Select FILE SERVER and select Enabled.

3. Select UNIVERSAL TERMINAL and select Enabled.

4. Select System /ISOBUS /UT .

The Universal Terminal setup page is displayed.

Inhaltsverzeichnis

Andere Topcon Controller Handbücher

Topcon

Topcon OPUS A3 Eco Technisches Datenblatt

Topcon

Topcon Liquid Systems CM-40 Bedienungsanleitung

Topcon

Topcon KB-50 Bedienungsanleitung

Topcon

Topcon X35 Bedienungsanleitung

Topcon

Topcon Wachendorff OPUS A8 ECO Bedienungsanleitung

Topcon

Topcon Norac UC5 Bedienungsanleitung

Topcon

Topcon ISOBUS Artemis Bedienungsanleitung

Topcon

Topcon Tesla Bedienungsanleitung

Topcon

Topcon System 350 Bedienungsanleitung

Topcon

Topcon T18 Bedienungsanleitung

Topcon

Topcon ASC-10 Installationshandbuch

Topcon

Topcon ISOBUS Athene - SL2 Bedienungsanleitung

Topcon

Topcon ISOCAN Bedienungsanleitung

Topcon

Topcon FC-2500 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung