Topcon Norac UC5 Bedienungsanleitung

Rogato

900, 1100, 1300

Active Wing Roll Control Option

Installation Manual

5466BC-RG

Reorder P/N: 5466BC-RG-INST Rev E (Rogator 900, 1100, 1300 Active Wing Roll Control

Option)

NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and

without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information

contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

Contents

1Introduction................................................................................................................ 1

2Kit Parts ...................................................................................................................... 2

3Hydraulic Installation ................................................................................................ 6

4Electrical Installation ............................................................................................... 11

5Software Setup......................................................................................................... 15

6Cable Drawings ........................................................................................................ 17

1Introduction

Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This

system is manufactured with top quality components and is engineered using the latest

technology to provide operating reliability unmatched for years to come.

When properly used the system can provide protection from sprayer boom damage, improve

sprayer efficiency, and ensure chemicals are applied correctly.

Please take the time to read this manual completely before attempting to install the system. A

thorough understanding of this manual will ensure that you receive the maximum benefit from

the system.

Your input can help make us better! If you find issues or have suggestions regarding the parts

list or the installation procedure, please don’t hesitate to contact us.

If the Active Wing Roll Control Option is being installed on a sprayer with an

existing Active Roll system, a linear roll damper is needed and must be ordered

separately.

Part Number Name Quantity

44792-111 ROLL POSITION DAMPER 40.86 IA RG 1

44750-12 HARDWARE MOUNTING RPD - ROGATOR LSD TO RPD UPGRADE 1

Every effort has been made to ensure the accuracy of the information contained in

this manual. All parts supplied are selected to specially fit the sprayer to facilitate

a complete installation. However, NORAC cannot guarantee all parts fit as

intended due to the variations of the sprayer by the manufacturer.

Please read this manual in its entirety before attempting installation.

2Kit Parts

2.1 Kit Overview

Figure 1: UC5 Active Wing Roll Control Parts

2.2 Hydraulic Plumbing

Figure 2: UC5 Active Wing Roll Control Hydraulic Plumbing on Rogator 900, 1100, 1300

Components shown in black are included in this kit.

Components shown in blue are existing components.

2.3 List of Parts

Item Part Number Name Quantity

B05 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 1

B07 44749 BRACKET WRC 80MM V1 1

B12 44971-06 MOUNTING BRACKET EXTENSION FOR LOW PROFILE 4

B20 44971-01 SENSOR MOUNTING BRACKET LOW PROFILE 16GA - NO MOUNTING HARDWARE 2

C01 43220-03 CABLE UC5 NETWORK 14 AWG 3M 1

C10 43230-04 CABLE UC5 VALVE 2PIN DT TO 2PIN DT 2

E07 50100 ULTRASONIC MAX SENSOR 2

E12 43764 UC5 NETWORK COUPLER 2-WAY 1

H06 44863-31 HOSE ASSEMBLY 122R2-06 106 IN L 6FORX 6FORX 4

H11 44865-75 HYDRAULICS FITTING KIT - AWR1 1

H12 44868 ACCUMULATOR 10 CU INCH, 0.161 L, 900 PSI 2

H13 44862-18 HOSE ASSEMBLY 122R2-04 18 IN L 6FORX 6FORX 2

H14 44917 COUPLING HYD 6MB-6MOR MACHINED ORB 2

H20 44981 WING ROLL CYLINDER 80MM W/POSITION SENSOR 1

M03 5466BC-RG-INST MANUAL INSTALLATION UC5 ACTIVE WING ROLL OPTION ROGATOR 900, 1100, 1300 1

M04 100594 BOLT HEX NC GR5 PLTD 1/2X1 2

M05 100868 NUT LOCK NYLON NC PLTD 1/2 IN 2

M08 106903 BOLT U 304SS .38-16THDx2.12x3.06 - AG516992 4

M09 106906 NUT LOCK NYLON SS 3/8 IN 16

M10 106905 BOLT CARRIAGE SS 3/8X1-1/4 8

P03 105882 UC5 NETWORK 6 PIN PLUG 1

V02 44962D VALVE ASSEMBLY EXPANSION DPOC PROP DT 4 BOLT 1

2.4 Tools Required

This list is intended to be a guideline for what is required for installation. Additional tools may

be required or may work better.

SAE Wrenches (sizes 7/16" to 1")

Side-Cutting Pliers (for cable ties)

Power Drill

5/8" Drill Bit

Tape Measure

Center Punch and Small Hammer

(Optional)

2.5 Hydraulic Fitting Kit Details (P/N: 44865-75)

Item Part Number Name Quantity

Picture

F12 44917 MALE ADAPTER - 6MB 6MOR 6

F13 104586 TEE ADAPTER - 6FORXR 6MORT 4

F14 104590 90 DEG ADAPTER - 6MOR 6FORX90 9

6 M B - 6 M OR X 90

SIZE IN

1/16TH'S

GENDER: MALE

OR FEMALE

90° ANGLE

SWIVEL

TYPE

GENDER

SIZE

TYPE:

B - ORB

J - JIC

OR - FLAT

FACE

P - PIPE

Fitting Name

Example:

Do not use high speed power tools/drills when installing hardware.

The use of dielectric grease is not recommended on any NORAC electrical

connections.

To ensure all stainless steel hardware does not gall or seize apply a light coating of

the supplied Permatex Anti-seize grease to all threaded parts upon installation.

Permatex Anti-seize lubricant is preferred, but other similar anti-seize products

may be used.

3Hydraulic Installation

Ensure all pressure has been bled from the system before disconnecting any lines

or fittings. Hydraulic pressure will exist on the wing tilt circuits unless the wings

are being supported by other means. The hydraulic installation may be performed

with the wings in transport position, resting on the ground or with the tilt cylinders

fully extended.

Component failure due to oil contamination is not covered under the NORAC UC5

system warranty. It is recommended that a qualified technician perform the

hydraulic installation.

3.1 Valve Assembly

1. On a clean surface remove the plastic plugs from the block.

2. Install the 6MB-6MOR (F12) fittings into the “A” and “B” ports of the expansion block.

Tighten to 18 ft-lbs (24 Nm).

Figure 3: NORAC Valve Block Details

3.2 Expansion Block Assembly

1. Remove the plate and 3/8” bolts from the end of the valve block. Remove any yellow paint

chips from the surface of the valve block to ensure a clean sealing surface.

2. Remove the four 4MBP plugs from the 2 station valve block (Figure 4). Gently tap the plugs

with a hammer to loosen before attempting to remove.

3. Coat the four o-rings in hydraulic oil and install them into the expansion block. Ensure the

o-rings are seated properly.

4. Attach the expansion block to the 2 station block using the included spring washers and

bolts.

5. Tighten the bolts to 31 ft-lbs (42 Nm).

Figure 4: NORAC Expansion Block Assembly

Inhaltsverzeichnis

Andere Topcon Controller Handbücher

Topcon

Topcon X35 Bedienungsanleitung

Topcon

Topcon KB-50 Bedienungsanleitung

Topcon

Topcon Liquid Systems CM-40 Bedienungsanleitung

Topcon

Topcon FC-2500 Bedienungsanleitung

Topcon

Topcon ISOCAN Bedienungsanleitung

Topcon

Topcon ISOBUS Athene - SL2 Bedienungsanleitung

Topcon

Topcon System 350 Bedienungsanleitung

Topcon

Topcon Wachendorff OPUS A8 ECO Bedienungsanleitung

Topcon

Topcon Athene SM-1 Bedienungsanleitung

Topcon

Topcon OPUS A3 Eco Technisches Datenblatt

Topcon

Topcon ASC-10 Installationshandbuch

Topcon

Topcon ISOBUS Artemis Bedienungsanleitung

Topcon

Topcon T18 Bedienungsanleitung

Topcon

Topcon Tesla Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch