Topcon Liquid Systems CM-40 Bedienungsanleitung

SETUP GUIDE

TOPCON APOLLO

FAST SHUTOFF - SINGLE LIQUID - SECTION CONTROL

DOCUMENT NO. MAN0034

REVISION A

REVISION DATE 18/01/2022

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 2 / 28

Revision. A Rev. Date 18/01/2022

Overview

This document provides instructions for setting up a Fast Close Control Valve equipped Liquid

Systems (SA) Rate Control Module with Topcon Apollo CM-40 ECU as the Master Controller

and EM-24 Expansion Module for section control using Topcon X25, X35, XD+ and XD Console.

The CM-40 ECU can control up to 4 application channels. This scenario covers setup of a single

liquid system with section control. A second liquid channel with section control can be setup

by following the same instructions again.

This document should be read in conjunction with relevant Topcon Apollo Seeder Control

Operator’s Manual.

CM-40 Master Controller EM-24 Expansion Module

Configuration Prerequisites

Before the liquid system can be configured in the X Series Console following steps need to be

completed.

 Physical installation of Liquid Systems (SA) Rate Control module including tank plumbing.

 Physical installation of a Stacker distribution system on the tool bar or planter.

 Installation and connection of Apollo CM-40 & EM-24 ECUs to X Series Console using

appropriate Topcon harnesses.

 Product tanks filled with enough water to conduct testing.

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 3 / 28

Revision. A Rev. Date 18/01/2022

Physical Connection to Liquid Systems module

Connect Liquid Systems (SA) module to the Apollo CM-40 & EM-24 ECUs with wiring looms

supplied. Liquid Systems (SA) looms available for single liquid set up with section control are:

Part No. Name Description

TC-1013026-01 Apollo CM-40 Adapter

Loom

Adapt

r that c

onnects to

CM-40 ECU.

TC-1013025-01

Apollo EM-24 Section

Adapter Loom

Adapter that connects to

EM-24 ECU.

LL07011 Generic Module Loom

(5m)

Connect

s to individual

device connectors on LQS

pump module.

Connects to TC-1013026-

01 Adapter Loom via 23

pin circular connector.

LL07013

LL07023

Section Loom

(12 Sections, 6m)

Section Loom

(6 Sections, 6m)

Connects to individual

section valve connectors

on LQS section module.

Connects to TC-1013025-

01 Adapter Loom via 20

pin circular connector.

LL07014

(optional)

LL07021

(optional)

Section Loom Extension

(12 Section, 6m)

Section Loom Extension

(12 Section, 12m)

Extensions of

ection

Loom for when additional

length is required from

LQS section module to

EM-24 ECU.

LL07015

(optional)

LL07020

(optional)

Generic Module Loom

Extension (6m)

Generic Module Loom

Extension (12m)

Extensions of

eneric

Module Loom for when

additional length is

required from LQS pump

module to CM-40 ECU.

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 4 / 28

Revision. A Rev. Date 18/01/2022

1. Plug Apollo CM-40 Adapter Loom (TC-1013026-01) into CM-40 ECU. Ensure it is

connected to the correct channel for liquid tank. e.g., if tank 3 is set up for liquid, then

plug connector into channel 3.

2. Connect the other end of Apollo CM-40 Adapter Loom to Generic Module Loom

(LL07011). Connect & route Extension Looms (LL07015 or LL07020) in between if

additional length is required to reach LQS pump module.

3. Connect Generic Module Loom to device connectors (FSO valve signal and power, flow

meter, pressure sensor & RPM sensor) on Liquid Systems (SA) module.

Apollo CM

Adapter Loom

(TC-1013026-01)

Generic Module

Loom (LL07011)

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 5 / 28

Revision. A Rev. Date 18/01/2022

4. Plug Apollo EM-24 Section Adapter Loom (TC-1013025-01) into Relays 1 port on EM-24

ECU

5. Connect the other end of Apollo EM-24 Section Adapter Loom to Section Loom (LL07013

or LL07023). Connect & route Section Extension Looms (LL07014 or LL07021) in between

if additional length is required to reach LQS section module.

Connect Valve Power connector on Apollo EM-24 Section Adapter Loom to Valve Power

receptacle on the Seeder Harness.

Section Loom

(LL07013 or

LL07023)

Apollo EM

24 Section

Adapter Loom

(TC-1013025-01)

Valve Power

Connector

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 6 / 28

Revision. A Rev. Date 18/01/2022

6. Connect Section Loom (LL07013 or LL07023) to individual connectors on the Liquid

Systems (SA) section module. Ensure section valve number matches connector number.

e.g., valve No. 1 plugs in to connector No.1. Insert dust plugs into un-used connectors on

the Section Loom.

Insert dust plugs in

un-used connectors

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 7 / 28

Revision. A Rev. Date 18/01/2022

Apollo CM-40 & EM-24 ECU Setup

Before the module can be setup, a new implement profile with a liquid tank must be created.

Select Setup icon (bottom left corner) on the run screen to enter main setup

screen.

Select Implement, New & Custom, then select the appropriate configuration.

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 8 / 28

Revision. A Rev. Date 18/01/2022

The implement should be configured with:

IMPLEMENT CONTROL: Section Control and Rate Control

ECU TYPE: Apollo

IMPLEMENT FUNCTION: Seeder

ECUs: CM40 and EM-24

At least 1 Liquid Boom and 1 liquid tank need to be created.

Ensure the EM-24 is not connected to the CM-40 ‘comms’ port while the system detects the

first ECU. Once the CM-40 has been detected, select the Add ECU icon, remove dust cap and

connect the CAN line to the EM-24 ‘comms’ port.

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 9 / 28

Revision. A Rev. Date 18/01/2022

`Select Section Control/Monitoring as the function for the EM-24

Select Liquid for the appropriate tank and which drive for each tank according to the port

connected on the CM-40. E.g.- Channel 1 is Drive 1

Setup Guide TOPCON Apollo FSO - Single Liquid - Section Control

Doc. No. MAN0034 P 10 / 28

Revision. A Rev. Date 18/01/2022

Geometry Setup

Select Implement and Geometry, then select the boom which will be used for guidance.

Select the boom used on the side tab and set the measurements according to the

implement used.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Topcon Controller Handbücher

Topcon

Topcon Wachendorff OPUS A8 ECO Bedienungsanleitung

Topcon

Topcon ISOBUS Athene - SL2 Bedienungsanleitung

Topcon

Topcon X35 Bedienungsanleitung

Topcon

Topcon ISOCAN Bedienungsanleitung

Topcon

Topcon KB-50 Bedienungsanleitung

Topcon

Topcon OPUS A3 Eco Technisches Datenblatt

Topcon

Topcon T18 Bedienungsanleitung

Topcon

Topcon Tesla Bedienungsanleitung

Topcon

Topcon ISOBUS Artemis Bedienungsanleitung

Topcon

Topcon ASC-10 Installationshandbuch

Topcon

Topcon Norac UC5 Bedienungsanleitung

Topcon

Topcon System 350 Bedienungsanleitung

Topcon

Topcon FC-2500 Bedienungsanleitung

Topcon

Topcon Athene SM-1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch