Topcon OS Series Bedienungsanleitung

TOPCON OS SERIES TOTAL STATION AND MAGNET FIELD

OS Series Resection Setup Quick Guide

This Quick Guide is to show you how to setup and orientate the Topcon OS Series Total

Station using the Resection Method.

Principles of a Resection:

Resection is used to determine the coordinates of an instrument position (station point) by

performing multiple measurements of points whose coordinate values are known.

We need a minimum of two known points to perform a

resection, but the more points that are known and

used, the higher the precision of the calculated

instrument position. We would always recommend a

minimum of three known points to be used.

In this diagram you can see the Instrument is setup at

P0 and we have known points at positions P1 to P4.

We are going to use P1, P2 and P3 for our resection.

It is important to make sure that the battery is seated in the instrument prior to setting

the Total Station up as the weight of the battery will affect the level of the instrument.

Step One: Positioning the Instrument

1) Locate a position where you can observe at least two known

control points.

Make sure the Tripod legs are spaced at equal intervals and the

Tripod head is roughly level.

Make sure the Tripod feet are firmly fixed in the ground.

Tip: Set the height of the Tripod head at mid chest height to

ensure the telescope of the instrument is at eyelevel.

2) Place the Instrument on the Tripod head.

Supporting it with one hand, tighten the centring screw on the

bottom of the unit to make sure it is secured to the Tripod.

Step Two: Levelling

1) Centre the bubble in the circular level by either shortening the

Tripod leg closest to the off-centre direction of the bubble or by

lengthening the Tripod leg farthest away from the off-centre

direction of the bubble. Adjust one more Tripod leg to centre

the bubble.

Turn the levelling foot screws while checking the circular level

until the bubble is centred in the centre circle.

2) Turn on the OS Series using the Power Button.

The “Virtual Bubble” is shown on the screen.

“” indicates the bubble in the circular level.

3) Centre “” in the Circular level.

4) Turn the Instrument until the telescope is parallel

To a line between levelling foot screws A and B.

5) Set the tilt angle to 0˚ using foot screws A and B for the X direction and levelling screw

C for the y direction Remember Fingers and Thumbs! Always turn A and B in opposite

directions to half the error on each foot screw.

6) Press {ESC} on the instrument keypad to return to observation mode.

7) If the instrument does not automatically open the MAGNET Field software, press

{PRG} on the instrument keypad.

Select “MAGNET Field” from the listed programs

The remainder of the Resection setup procedure is completed using MAGNET Field.

Resection Setup using MAGNET Field on the Topcon OS

1) From the MAGNET Field home

screen, select the [Setup]

Option.

2) From the Setup options select

the [Resection] icon.

3) Define Instrument Setup:

We need to enter a unique ID for

the point the Total Station is

setup on. In this case P0.

There is no need to enter the

Height of the Instrument (HI).

Tap the [Next >>] Icon

4) MAGNET Field now asks you to

specify your first control point, in

this case “P1”. You can select

the point from the map or list

icons or manually enter the ID.

If the point is not in the

Database you will be taken to

the “Add Point” Screen. Enter

your Prism Height (0m in this

example)

Sight the Instrument on your

target and tap the “Measure” Icon.

5) MAGNET Field will now ask you

to specify another control point,

in this case P2. As before you

can select from the map, list or

manually enter. Don’t forget to

enter your pole height!

Tap the “Measure” Icon

6) MAGNET Field will now take you

to the results screen which will

show you the residuals from

your initial two measurements.

We could accept this result by

tapping the [Accept] icon, but we

recommend adding a third

known point. To add a third

point, tap the [Add] icon.

7) MAGNET Field will take you to

the same screen we saw in step

5, we have selected known point

P3 (Don’t forget pole height!) and

tapped the “Measure”

icon.

8) MAGNET Field returns us to our

results screen and we can now

check our residuals, in this case,

EN and Z values are all zero,

which is a perfect result. In the

field, an error of a few mm is

perfectly normal.

We can check the individual

results in the table and if needed,

we can remove the measurement

by highlighting and tapping the

[Remove] icon, or remeasure by tapping the [Re-Meas] icon. If you are happy with

your result, tap the [Home] Icon to the top right of the screen and you will be returned

to the home screen, setup and orientated and ready to survey or stake out.

End.

Inhaltsverzeichnis

Andere Topcon Messgerät Handbücher

Topcon

Topcon Synergy GM-50 series Bedienungsanleitung

Topcon

Topcon DIGI-STAR TMR3610 Bedienungsanleitung

Topcon

Topcon OS-101 Bedienungsanleitung

Topcon

Topcon GM-100 Series Bedienungsanleitung

Topcon

Topcon Sokkia FX Series Bedienungsanleitung

Topcon

Topcon PS Series Bedienungsanleitung

Topcon

Topcon CL-300 Bedienungsanleitung

Topcon

Topcon KR-1W Bedienungsanleitung

Topcon

Topcon BM-100 Series Bedienungsanleitung

Topcon

Topcon UVR-T2 Bedienungsanleitung

Topcon

Topcon TP-L5GV Bedienungsanleitung

Topcon

Topcon IM-600 Bedienungsanleitung

Topcon

Topcon RL-VH3G Bedienungsanleitung

Topcon

Topcon i-33 Bedienungsanleitung

Topcon

Topcon GPT-3002W Series Bedienungsanleitung

Topcon

Topcon RM-8800 Bedienungsanleitung

Topcon

Topcon GTS-230N Bedienungsanleitung

Topcon

Topcon CL-200 Bedienungsanleitung

Topcon

Topcon GTS-750 Series Bedienungsanleitung

Topcon

Topcon RL-H4C Bedienungsanleitung

Topcon

Topcon GT560 AUTOLOG Bedienungsanleitung

Topcon

Topcon CL-300 Betriebsanleitung

Topcon

Topcon CT-800 Bedienungsanleitung

Topcon

Topcon UA-10 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung