Tornado NAVY Bedienungsanleitung

Specifications

Wing Span 63in.

Wing Area 1007.5 sq in.

Flying Weight 14.3 lb.

Fuselage Length 76.8 in.

Engine 12lb.-18lb. Thrust Turbine

Recommended Engine Jet Cat P60SE

Warning!!! This is not a toy.

The TORNADO is designed for maximum performance. If you

are not familiar with the operation of turbine powered aircraft

please seek the advice of an experienced modeler. Operating

this model without prior preparation and experience can cause

injuries.

1. Read through the instruction manuel thoroughly before beginning

construction

Before You Begin

2. Check all parts supplied with the kit for defects, and missing parts.

Dry fit all parts that will be glued for proper fit. If any parts are

found to be defective please contact local dealer for assistance.

3. Use proper adhesives for assembly, It is imperative that all glue

joints be very strong for best results and safety.

1. Hysol or 15 Min epoxy with micro balloons

Adhesive Required:

2. 30 min epoxy

3. Medium CA

4. Zap-A-Dapa GOO or Automotive Goop

1. Turbine 12lb-18lb thrust

Required Parts for Final Assembly

2. TX and RX with a minimum of 7 channels

3. 4- mini servos with a minimum of 65oz torque for Empennage

4. 5- Standard size servos with a minimum of 120oz torque for

Ailerons,Flaps and Nose wheel steering

5. 1- Standard servo for retract valve

6. Electronic Brake Valve or Mechanical Brake valve

7. UAT

8. RX battery with a minimum of 2,200 mah 6v

9. 2 5/8 Wheels and Brakes for Main Gear, 2/14 Nose wheel

10. A minimum of 3/8 struts for Mains and Nose

11. Pull-Pull cable for steering

PARTS LIST

1. Fuselage 11. 2 Aulminum wing bolts

2. Main Wing 1 pair 12. 4 Aluminum Elevator Bolts

3. Stabilizer 1 set 13. 8 Control Clevis

4. Rudder 1 set 14. 8 Pushords

5. Canopy 15. 8 Ball links

6. ABS Canopy Tub 16. 2 Aluminum Wing Tubes

7. 80oz Composite Fuel Tank 17. 1 Set Spring Air Retracts

8. Composite control horns 8 pieces

9. Aluminum Engine Mount

10.4 Aluminum Boom Bolts and Washer

Locate the plastic hinges with pin and fit into slots that are cut into the wing

panels, trim slot as necessary. Hinge the Ailerons and Flaps on each wing

panel using Hysol or 30 min epoxy.

Check the control surfaces on each wing panel and ensure that the glue

has cured and the control surface is secure. Locate the servo openings for

the ailerons and flap’s and install the servo’s using wood screws on each

wing, ensure the servo’s are facing in the correct direction as per the above

illustration

Locate 4 composite control horns and cut a slot in each aileron and flap for

the control horn. Use 30 min epoxy or hysol to secure horn in place and let

cure. Assemble a pushrod using one clevis and ball link and secure to

servo. Pay close attention to have a slop free surface, any excess

movement can cause flutter during high speed flight.

Hinge the rudder using 30

min epoxy or hysol and let

cure. Check the control

surface after the glue has

cured and ensure of a good

bond. Locate the servo

openings on each boom and

install a servo using wood

screws. Locate 2 control

horns and cut a slot in each

rudder and glue in place

using 30 min epoxy or hysol.

Locate the fuselage and using a dremel make a hole for all turbine wires

and fuel lines. It is very important to make the hole large enough for the

starter motor to fit inside without touching the walls of the fuselage or

chaffing any of the fuel lines or wires.

Install the turbine as per the manufactures instructions ensure that you

move the turbine as far forward as possible for CG purposes.

Drill a pilot hole and then dremel out as to

accommodate the wing spars,wing bolt,

servo wires and air lines. After this is

complete test fit the wing panels to ensure a

proper fit.

Hinge the elevator using 30 min epoxy or hysol and let cure. After the glue

has fully cured check control surface for a proper bond.

Cut the covering off approximately 1/2 inch from the end of the elevator this

part will go inside the booms

9. Fit both wings onto the to the fuselage using the aluminum spars

supplied and bolt them in place. Locate both booms and stabilizer and put

aside for assembly in the next steps. Attach one of the booms ( your

choice ) on to the wing using the bolts and washers supplied and ensure

that the stabilizer opening is facing inward. Now locate the other boom and

attach it to the the other wing only using the forward bolt and washer. This

will allow you to pivot the boom slightly so you can fit the stabilizer in place

for glueing.

Locate the stabilizer and temporarily attach it to each boom using the bolts

supplied for a test fit prior to glueing. Remove any covering from the

stabilizer as to ensure a proper bonding surface. After you are satisfied with

the fit remove the 4 bolts and apply hysol or 30 minute epoxy with micro

balloons to the stabilizer and the inside of the cavity in the boom. Attach the

stabilizer with the 4 bolts and washers and tighten. Screw the last bolt

through the wing into the boom and ensure you have 2 bolts on each wing.

Now ensure that the stabilizer is parallel to the wing and the booms are

properly fit to the stabilizer and let cure over night. After the glue has cured

use 15 minute epoxy with micro balloons and fill any gaps that are present

between the stabilizer and the boom cavity.

Inhaltsverzeichnis

Andere Tornado Spielzeug Handbücher

Tornado

Tornado Genesis Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung