Toro 3200 Bedienungsanleitung
FormNo.3458-441RevB
WinterEnclosure
Groundsmaster®3200or3300SeriesTractionUnit
ModelNo.31990—SerialNo.400000000andUp
Operator'sManual
Safety
ThisproductcomplieswithallrelevantEuropean
directives.Fordetails,pleaseseetheDeclarationof
Incorporation(DOI)atthebackofthispublication.
RolloverProtectionSystem
(ROPS)foraCab
•TheROPSisanintegralpartofthecab,whichis
aneffectivesafetydevice.
•TheROPSconsistsoftherollbar,theseat,the
seatbelt,theseatlatch,andcab.
•Alwaysweartheseatbeltwhenyouoperatethe
machinewithacab.
•Ensurethattheseatbeltcanbereleasedquickly
intheeventofanemergency.
•Driveslowlyandcarefully.
•Checkcarefullyforoverheadclearances(i.e.,
branches,doorways,electricalwires)before
drivingunderanyobjectsanddonotcontactthem.
•Keepthecabinsafeoperatingconditionby
periodicallythoroughlyinspectingfordamageand
keepingallmountingfastenerstight.
•Replaceadamagedcab.Donotrepairorrevise.
•DonotremoveormodifytheROPS.
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal93-7272
93-7272
1.Cutting/dismembermenthazard;fan—stayawayfrom
movingparts.
decal125-9688
125-9688
1.Windshieldwipers—off3.Windshieldwipers—on
2.Windshieldwipers4.Spraywindshieldwasher
uid
©2022—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3458-441*
decal130-5361
130-5361
1.Warning—readtheOperator'sManual;operatethemachine
onlyfromthedriver'sseat;wearaseatbelt;wearhearing
protection.
decal140-4413
140-4413
1.Warning—donottouchthehotsurface.
decal140-6632
140-6632
1.ReadtheOperator’s
Manualforfuse
information.
4.Fanandinteriorlight(40
A)
2.A/Cclutchandcondenser
fan(25A)
5.Frontofmachine
3.Windshieldwasher(20A)
2
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
Bolt(3/4x4inches)2
1Nut(3/4inch)2Preparethemachineandcab.
2Cabrewall1Installthecabrewall.
Cab1
LeftROPSstop1
RightROPSstop1
ROPSmount2
ROPSbrace2
Retainercover2
Seal2
Screw(1/4x3/4)8
Bolt(3/8x1inch)4
Locknut(3/8inch)4
3
Foamseal1
Installthecab.
Bolt(5/16x1-1/2inch)2
Nut(5/16inch)2
Plateclamp2
4Tubeclamp2
Installtheventtubes.
Stepmount1
Carriagebolt(3/8x7/8inch)2
Nut(3/8inch)2
Carriagebolt(5/16x3/4inch)2
Carriagebolt(5/16x1-1/4inch)1
Nut(5/16inch)3
Deckstep1
5
Floormat1
Installthestep.
Hose1
Femalecoupler1
Femaledustplug1
Straighttting(3/8NPTx5/8barb)2
Hoseclamp4
Malecoupler1
Maledustplug1
R-clamp2
Carriagebolt(1/4x3/4inch)2
Flangenut(1/4inch)2
Enginetting2
Cableties8
Straightadaptor(3/8inch)1
6
Adaptor(M16)1
Installthehosesforthe24hpengine.
3
ProcedureDescriptionQty.Use
Hose1
Femalecoupler1
Femaledustplug1
Straighttting(3/8NPTx5/8barb)2
Hoseclamp4
Malecoupler1
Maledustplug1
R-clamp2
Carriagebolt(1/4x3/4inch)2
Flangenut(1/4inch)2
Enginetting2
Cableties8
Straightadaptor(3/8inch)1
7
Adaptor(M16)1
Installthehosesforthe37hpengine.
Washer-uidbracket1
Washer-uidtank1
Carriagebolt(5/16x3/4inch)4
8Locknut(5/16inch)4
Installthewasher-uidtank.
Female-hosetting1
9Male-hosetting1Installthewasheruidhoses.
10Fuse(10A)1Connectthewireharness.
Weight(6kgor15lb)2
Bolt(3/8x3-1/2inches)2
Washer(3/8inch)2
11Locknut(3/8inch)2
Installtheweights.
12Nopartsrequired–Completetheinstallation.
4
1
PreparingtheMachineand
Cab
Partsneededforthisprocedure:
2Bolt(3/4x4inches)
2Nut(3/4inch)
Procedure
Note:Savetheshippingpalletforlongtermstorage
afterthecabisremoved.Saveallhardwareforthe
machinewheninstallingorremovingthecab.
1.Parkthemachineonalevelsurface,engagethe
parkingbrake,lowertheattachment,shutoffthe
engine,andremovethekey.
2.Disconnectthenegative(-)batterycablefrom
thebattery.
3.Removethenut,bolt,andspacersecuringthe
cabletothetractionpedalandrotatethepedal
towardstheseat(Figure1).
g301596
Figure1
1.Footpedal3.Bolt
2.Locknut4.Spacer
4.RemovetheROPSpinsandplacetheminto
downpositionhole(Figure2).
g302033
Figure2
1.Cotterpin2.Pin
5.Installthebolt(3/4x4inches)intothetophole
oftherollbarandsecureitngertightwithanut
(3/4inch).Referto(Figure3).
Note:Ensurethattheboltisinstalledonthe
insideoftherollbar.
g302032
Figure3
1.Installthebolt(3/4x4
inches)ontheinside.
2.Nut(3/4inch)
6.Removethefrontmower-decklatchfromthe
frontofthemachine(Figure4).Savethelatch
andhardware.
5
g302034
Figure4
1.Nut3.Bolt
2.Mower-decklatch
7.Removethenutsandboltsfromtherightarmrest
andfoldittothecenter(Figure5).
g301595
Figure5
1.Bolt2.Locknut
8.Tiltthesteeringcolumntoitslowestposition;
refertotheOperatorsManual.
9.RemovetheR-clampsfromtherollbarsecuring
theventtubes(Figure6).
10.Laytheventtubesoutofthewayformounting
thecab.
11.InstalltheR-clampsbackintotherollbarwithout
theventtubes(Figure6).
g301597
Figure6
1.Bolt3.R-clamp
2.Fuel-venttube
6
2
InstallingtheCabFirewall
Partsneededforthisprocedure:
1Cabrewall
Procedure
1.Caulktheexistingrewallopeningsonboth
sidesatthelocationsshowninFigure7with
blackRTVsealant.
g301598
Figure7
1.Caulktheseareasonbothsides.
2.Caulkthecabrewallatthelocationsshownin
Figure8withblackRTVsealant.
g336508
Figure8
1.Caulktheseareasonly
3.Removetheexistinghardwarethatconnectsthe
existingrewalltotherollbartube.
4.Placethecabrewallaroundtheseatandonto
theexistingrewall(Figure9).
7
g301513
Figure9
1.Cabrewall3.Existingrewall
2.Existinghardware—reuse
5.Usetheexistinghardwaretoinstallthecab
rewall.
3
InstallingtheCab
Partsneededforthisprocedure:
1Cab
1LeftROPSstop
1RightROPSstop
2ROPSmount
2ROPSbrace
2Retainercover
2Seal
8Screw(1/4x3/4)
4Bolt(3/8x1inch)
4Locknut(3/8inch)
1Foamseal
Procedure
Important:Looselyinstallthefastenersforthe
cabuntilallhardwareisinstalled.Afterallthe
hardwareisinstalled,tightenthefasteners.
1.Removetheleftandrightpanelsfrominsidethe
cabasshowninFigure10.
8
g301842
Figure10
1.Leftpanel2.Screws
2.RemovethecabroofasshowninFigure11.
g302035
Figure11
1.Bolt3.Cabroof
2.Washer
3.Useahoisttosupportthecabandconnectthe
cabhoisttothe4liftpointsonthecab(Figure
12).
Note:Acabhoistisavailablethroughyour
authorizedT orodistributor.
g322358
Figure12
1.Frontliftpoint2.Rearliftpoint
4.Raisethecabwithahoist(Figure12).
5.Installthefoamsealonthebottomofthecab
asshowninFigure13.
9
g301543
Figure13
1.Foamseal2.Foamsealinstalled
6.Alignthecabovertherollbar.
7.Whileloweringthecab,positiontheventtubes
throughtherearposts(Figure16).
Note:Ensurethatthetractionpedalisrotated
rearwardtowardstheseat.
8.Lowerthecabuntilitisapproximately51mm(2
inches)abovetherewallandmachine.
9.Installtherollbarsealsaroundeachsideofthe
rollbar(Figure14).
10.Installtheleftcoverand1retainercoverintothe
leftsealandsecurethecoverswith4screws
(1/4x3/4inches);refertoFigure14.
11.Installtherightcoverand1retainercoverinto
therightsealandsecurethecoverswith4
screws(1/4x3/4inches);refertoFigure14.
g301688
Figure14
1.Retainercover4.Rightcover
2.Rollbarseal5.Leftcover
3.Screws(1/4x3/4inches)6.Coversinstalled
12.Lowerthecabontotherewallandmachine.
13.Looselyinstallthemowerdecklatchtothefront
ofthecab(Figure4).
14.LooselyinstalltheROPSmountstosecurethe
cabtotherollbaronthemachine(Figure15).
15.LooselyinstalltheleftROPSstoponthecorner
oftherollbarwith2bolts(3/8x1inch),aROPS
brace,and2nuts(3/8inch).
16.LooselyinstalltherightROPSstoponthecorner
oftherollbarwith2bolts(3/8x1inch),aROPS
brace,and2nuts(3/8inch).
10
Andere Handbücher für 3200
7
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
