Toro 03550 Reelmaster 5500-D Bedienungsanleitung

PART NO. 00075SL (Rev. D)

Service Manual

Reelmaster5500-D

Preface

The purpose of this publication is to provide the service

technician with information for troubleshooting, testing,

and repair of major systems and components on the

Reelmaster 5500-D.

REFER TO THE TRACTION UNIT AND CUTTING

UNIT OPERATOR’S MANUALS FOR OPERATING,

MAINTENANCE AND ADJUSTMENT INSTRUC-

TIONS. Space is provided in Chapter 2 of this book to

insert the Operator’s Manuals and Parts Catalogs for

your machine. Replacement Operator’s Manuals are

available by sending complete Model and Serial Num-

ber to:

The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420–1196

The Toro Company reserves the right to change product

specifications or this publication without notice.

This safety symbol means DANGER, WARNING,

or CAUTION, PERSONAL SAFETY INSTRUC-

TION. When you see this symbol, carefully read

the instructions that follow. Failure to obey the

instructions may result in personal injury.

NOTE: A NOTE will give general information about the

correct operation, maintenance, service, testing, or re-

pair of the machine.

IMPORTANT: The IMPORTANT notice will give im-

portant instructions which must be followed to pre-

vent damage to systems or components on the

machine.

The Toro Company – 2000, 2002, 2003, 2004, 2007

Reelmaster 5500-D

Safety

Product Records

and Maintenance

Kubota

Diesel Engine

Hydraulic

System

Electrical

System

Differential

Axle

Steering

and Brakes

Rev. D

Reelmaster 5500-D

Table Of Contents

Chapter 1 − Safety

General Safety Instructions 1 – 1. . . . . . . . . . . . . . . . . .

Jacking Instructions 1 – 4. . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2 – Product Records and Maintenance

Product Records 2 – 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 2 − 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equivalents and Conversions 2 – 2. . . . . . . . . . . . . . . .

Torque Specifications 2 – 3. . . . . . . . . . . . . . . . . . . . . . .

Chapter 3 – Kubota Diesel Engine

Introduction 3 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 3 – 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Information 3 – 4. . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 3 – 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 3 – 8. . . . . . . . . . . . . . . . . . . . . . . .

KUBOTA WORKSHOP MANUAL, 05 SERIES DIESEL

ENGINE

Chapter 4 – Hydraulic System

Specifications 4 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Information 4 – 3. . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Schematics 4 – 8. . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Flow Diagrams 4 – 12. . . . . . . . . . . . . . . . . . .

Special Tools 4 – 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 4 – 24. . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing 4 – 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 4 – 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 4 – 41. . . . . . . . . . . . . . . . . . . . . . .

Chapter 5 – Electrical System

Electrical Schematics, and Electrical Harness and Con-

nectors Drawings 5 – 2. . . . . . . . . . . . . . . . . . . . . . . . .

Special Tools 5 – 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 5 – 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical System Quick Checks 5 – 15. . . . . . . . . . . . .

Component Testing 5 – 16. . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 5 – 35. . . . . . . . . . . . . . . . . . . . . . .

Chapter 6 – Differential Axle

Introduction 6 – 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications 6 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Tools 6 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 6 – 3. . . . . . . . . . . . . . . . . . . . . . . .

Chapter 7 – Steering and Brakes

Introduction 7 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Steering Schematics 7 – 3. . . . . . . . . . . . . . . . .

Specifications 7 – 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Tools 7 – 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 7 – 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing 7 – 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 7 – 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repairs 7 – 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reelmaster 5500-D

Groomer4WD Rear Axle

Electrical

Diagrams Cutting Units

Rev. C

Reelmaster 5500-D

Table Of Contents

Chapter 8 – Cutting Units

Specifications 8 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Tools 8 – 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 8 – 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Initial Set−up and Adjustments 8 – 7. . . . . . . . . . . . . . .

Daily Adjustments 8 − 16. . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 8 – 16. . . . . . . . . . . . . . . . . . . . . . .

Chapter 8.1 – Groomer

Troubleshooting 8.1 – 2. . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 8.1 – 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 8.1 – 5. . . . . . . . . . . . . . . . . . . . . .

Chapter 9 – 4WD Rear Axle

Specifications 9 – 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Information 9 – 3. . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 9 – 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repairs 9 – 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 10 – Electrical Diagrams

Electrical Schematics 10 – 3. . . . . . . . . . . . . . . . . . . . . .

Electrical Harness Drawings 10 − 5. . . . . . . . . . . . . . . .

Reelmaster 5500-D

Safety

Reelmaster 5500-D Page 1 - 1 Safety

Chapter 1

Safety

Table of Contents

GENERAL SAFETY INSTRUCTIONS 1. . . . . . . . . . . .

Before Operating 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .

While Operating 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance and Service 3. . . . . . . . . . . . . . . . . . . .

JACKING INSTRUCTIONS 4. . . . . . . . . . . . . . . . . . . . .

General Safety Instructions

The REELMASTER 5500-D was tested and certified by

TORO for compliance with the B71.4-1990 specifica-

tions of the American National Standards Institute. Al-

though hazard control and accident prevention partially

are dependent upon the design and configuration of the

machine, these factors are also dependent upon the

awareness, concern, and proper training of the person-

nel involved in the operation, transport, maintenance,

and storage of the machine. Improper use or mainte-

nance of the machine can result in injury or death. To re-

duce the potential for injury or death, comply with the

following safety instructions.

WARNING

To reduce the potential for injury or death,

comply with the following safety instructions.

Before Operating

1. Read and understand the contents of the traction

unit and cutting unit Operator’s Manual before starting

and operating the machine. Become familiar with the

controls and know how to stop the machine and engine

quickly. A replacement manual is available by sending

the complete model and serial number to:

The Toro Company

8111 Lyndale Avenue South

Bloomington, Minnesota 55420–1196.

2. Never allow children to operate the machine. Do not

allow adults to operate machine without proper instruc-

tion. Only trained operators who have read this manual

should operate this machine.

3. Never operate the machine when under the influ-

ence of drugs or alcohol.

4. Keep all shields, safety devices and decals in place.

If a shield, safety device or decal is defective, illegible or

damaged, repair or replace it before operating the ma-

chine. Also tighten any loose nuts, bolts or screws to en-

sure machine is in safe operating condition.

5. Always wear substantial shoes. Do not operate ma-

chine while wearing sandals, tennis shoes, sneakers or

when barefoot. Do not wear loose fitting clothing that

could get caught in moving parts and possibly cause

personal injury. Wearing safety glasses, safety shoes,

long pants and a helmet is advisable and required by

some local ordinances and insurance regulations.

6. Assure interlock switches are adjusted correctly so

engine cannot be started unless traction pedal is in

NEUTRAL and cutting units are DISENGAGED.

7. Remove all debris or other objects that might be

picked up and thrown by the reels or fast moving compo-

nents from other attached implements. Keep all by-

standers away from operating area.

8. Since diesel fuel is highly flammable, handle it care-

fully:

A. Use an approved fuel container.

B. Do not remove fuel tank cap while engine is hot or

running.

C. Do not smoke while handling fuel.

D. Fill fuel tank outdoors and only to within an inch of

the top of the tank, not the filler neck. Do not overfill.

E. Wipe up any spilled fuel.

Reelmaster 5500-D

Page 1 - 2

Safety

While Operating

9. Sit on the seat when starting and operating the ma-

chine.

10.Before starting the engine:

A. Engage the parking brake.

B. Make sure traction pedal is in NEUTRAL and the

ENABLE / DISABLE switch is in DISABLE.

C. After engine is started, release parking brake and

keep foot off traction pedal. Machine must not move.

If movement is evident, the neutral return mecha-

nism is adjusted incorrectly; therefore, shut engine

off and adjust until machine does not move when

traction pedal is released.

11.Seating capacity is one person. Therefore, never

carry passengers.

12.Do not run engine in a confined area without ade-

quate ventilation. Exhaust fumes are hazardous and

could possibly be deadly.

13.Check interlock switches daily for proper operation.

If a switch fails, replace it before operating the machine.

The interlock system is for your protection, so do not by-

pass it. Replace all interlock switches every two years.

14.Using the machine demands attention and to pre-

vent loss of control:

A. Operate only in daylight or when there is good ar-

tificial light.

B. Drive slowly

C. Watch for holes or other hidden hazards.

D. Look behind machine before backing up.

E. Do not drive close to a sand trap, ditch, creek or

other hazard.

F. Reduce speed when making sharp turns and

turning on a hillside.

G. Avoid sudden stops and starts.

15.Traverse slopes carefully. Do not start or stop sud-

denly when traveling uphill or downhill.

16.Operator must be skilled and trained in how to drive

on hillsides. Failure to use caution on slopes or hills may

cause loss of control and vehicle to tip or roll possibly re-

sulting in personal injury or death. On 4–wheel drive

models, always use the seat belt and ROPS together.

17.If engine stalls or loses power and cannot make it to

the top of a slope, do not turn machine around. Always

back slowly straight down the slope.

18.DON’T TAKE AN INJURY RISK! When a person or

pet appears unexpectedly in or near the mowing area,

STOP MOWING. Careless operation, combined with

terrain angles, ricochets, or improperly positioned

guards can lead to thrown object injuries. Do not resume

mowing until area is cleared.

19.Do not touch engine, muffler or exhaust pipe while

engine is running or soon after it is stopped. These areas

could be hot enough to cause burns.

20.If cutting unit strikes a solid object or vibrates abnor-

mally, stop immediately, turn engine off, set parking

brake and wait for all motion to stop. Inspect for damage.

If reel or bedknife is damaged, repair or replace it before

operating. Do not attempt to free blocked cutting unit by

reversing reel direction. Damage to reel may result.

21.Before getting off the seat:

A. Move traction pedal to neutral.

B. Set parking brake.

C. Disengage cutting units and wait for reels to stop.

D. Stop engine and remove key from switch.

E. Toro recommends that anytime the machine is

parked (short or long term) the cutting units should

be lowered to the ground. This relieves pressure

from the lift circuit and eliminates the risk of cutting

units accidentally lowering to the ground.

F. Do not park on slopes unless wheels are chocked

or blocked.

Safety

Reelmaster 5500-D Page 1 - 3 Safety

Maintenance and Service

22.Before servicing or making adjustments, stop engine

and remove key from the switch.

23.Make sure machine is in safe operating condition by

keeping all nuts, bolts and screws tight.

24.Make sure all hydraulic line connectors are tight, and

all hydraulic hoses and lines are in good condition be-

fore applying pressure to the system.

25.Keep body and hands away from pin hole leaks in hy-

draulic lines that eject high pressure hydraulic fluid. Use

cardboard or paper to find hydraulic leaks. Hydraulic

fluid escaping under pressure can penetrate skin and

cause injury. Fluid accidentally injected into the skin

must be surgically removed within a few hours by a doc-

tor familiar with this form of injury or gangrene may re-

sult.

26.Before disconnecting or performing any work on the

hydraulic system, all pressure in system must be re-

lieved by stopping engine and lowering cutting units to

the ground.

27.If major repairs are ever needed or assistance is de-

sired, contact an Authorized Toro Distributor.

28.To reduce potential fire hazard, keep engine area

free of excessive grease, grass, leaves and dirt. Clean

protective screen on front of engine frequently.

29.If engine must be running to perform maintenance or

an adjustment, keep hands, feet, clothing and other

parts of the body away from cutting units and other mov-

ing parts. Keep everyone away.

30.Do not overspeed the engine by changing governor

setting. To assure safety and accuracy, have an Autho-

rized Toro Distributor check maximum engine speed.

31.Shut engine off before checking or adding oil to the

crankcase.

32.Disconnect battery before servicing the machine. If

battery voltage is required for troubleshooting or test

procedures, temporarily connect the battery.

33.At the time of manufacture, the machine conformed

to the safety standards for riding mowers. To assure op-

timum performance and continued safety certification of

the machine, use genuine Toro replacement parts and

accessories. Replacement parts and accessories made

by other manufacturers may result in non-conformance

with the safety standards, and the warranty may be

voided.

34.When changing attachments, tires, or performing

other service, use correct blocks, hoists, and jacks.

Make sure machine is parked on a solid level floor such

as a concrete floor. Prior to raising the machine, remove

any attachments that may interfere with the safe and

proper raising of the machine. Always chock or block

wheels. Use jack stands or solid wood blocks to support

the raised machine. If the machine is not properly sup-

ported by blocks or jack stands, the machine may move

or fall, which may result in personal injury (see Jacking

Instructions).

Reelmaster 5500-D

Page 1 - 4

Safety

Jacking Instructions

CAUTION

When changing attachments, tires, or performing

other service, use correct blocks, hoists, and

jacks. Make sure machine is parked on a solid lev-

el surface such as a concrete floor. Prior to rais-

ing machine, remove any attachments that may

interfere with the safe and proper raising of the

machine. Always chock or block wheels. Use jack

stands or solid wood blocks to support the raised

machine. If the machine is not properly sup-

ported by blocks or jack stands, the machine may

move or fall, which may result in personal injury.

Jacking the Front End (Fig. 1)

1. Set parking brake and chock both rear tires to pre-

vent the machine from moving.

2. Position jack securely under the tie down rod that is

welded to the square tube of the front frame.

3. Position jack stands or hardwood blocks under the

square tube as close to the wheels as possible to sup-

port the machine.

Jacking the Rear End

1. The preferred method of lifting the rear end of the

machine is (Fig. 2):

A. Secure a chain fall or hoist to the tie down rod on

the rear of the frame.

B. Chock both front tires. Lift rear of the machine off

the ground.

C. On 2WD models, use jack stands or blocks under

the axle as close to the wheels as possible to secure

the machine.

D. On 4WD models, use jack stands or blocks under

the axle tube as close to the gear box housings as

possible to secure the machine.

2. If the rear of the machine can not be lifted as above:

A. On 2WD models, place jack securely under the

pivot bracket for the steering cylinder (Fig. 3).

B. On 4WD models, place jack securely under the

differential case (Fig. 2).

C. Chock both front tires. Jack rear of machine off

the ground.

Figure 1

1. Square tube (front frame)

1. Differential case

2. Axle tube 3. Gearbox housing

4. Tie down rod

Figure 2

1 2

1. Pivot bracket 2. Steering Cylinder

Figure 3

D. On 2WD models, use jack stands or blocks under

the axle as close to the wheels as possible to secure

the machine.

E. On 4WD models, use jack stands or blocks under

the axle tube as close to the gear box housings as

possible to secure the machine.

Andere Handbücher für 03550 Reelmaster 5500-D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro Reelmaster 2000-D 03431 Bedienungsanleitung

Toro

Toro 03664 Bedienungsanleitung

Toro

Toro 30984 Bedienungsanleitung

Toro

Toro 4540 Bedienungsanleitung

Toro

Toro 30857 Bedienungsanleitung

Toro

Toro ProLine 22158 Bedienungsanleitung

Toro

Toro GrandStand 18850TE Bedienungsanleitung

Toro

Toro 22296 Bedienungsanleitung

Toro

Toro 30934 Bedienungsanleitung

Toro

Toro 22293 Bedienungsanleitung

Toro

Toro Recycler 20370 Bedienungsanleitung

Toro

Toro 74787 Bedienungsanleitung

Toro

Toro TimeCutter SS 4235 Bedienungsanleitung

Toro

Toro 03805 Bedienungsanleitung

Toro

Toro 20068 Bedienungsanleitung

Toro

Toro 74602 Bedienungsanleitung

Toro

Toro 20955 Bedienungsanleitung

Toro

Toro 29730 Bedienungsanleitung

Toro

Toro 30329 Bedienungsanleitung

Toro

Toro TurfMaster 22207 Bedienungsanleitung

Toro

Toro GrandStand 134-3259 Bedienungsanleitung

Toro

Toro GrandStand 79534 Bedienungsanleitung

Toro

Toro DH 200 Handbuch

Toro

Toro 30626 Groundsmaster 328-D Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung