Toro Timecutter series Handbuch

Form No. 3356-867 Rev A

TimeCutter® Riding Mower

Model No. All models

Setup Instructions

Loose PartsUse the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Charge the battery.

Bolt (1/4 x 3/4 inch)

Washer

Nut (1/4 inch)

Connect the battery.

Seat

Spacers 2

Flat washers

Knobs

Install the seat.

Control lever

Bolt (1/4 x 3/4 inch)

Install the motion control levers.

Ignition Key

Operator’s Manual

Engine Operator’s Manual

Hose coupling

Operator Training Material

Complete thesetup.

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Step

Charging the Battery

No Parts Required

Procedure

Warning

CALIFORNIA

Pr oposition 65 W ar ning

Batter y posts, ter minals, and r elated

accessories contain lead and lead

compounds, chemicals kno wn to the State of

Calif or nia to cause cancer and r epr oducti v e

har m. W ash hands after handling .

Bulk electrolyte with 1.260 speciﬁc g ra vity m ust be

purc hased from a local batter y supply outlet.

1. Raise the seat to access the batter y . R emo v e

the batter y from the mac hine and place it on

a lev el surface; refer to the Operator’ s Manual ,

R emo ving the Batter y .

Important: Nev er ﬁll the batter y with

electr ol yte while the batter y is installed in

the tractor . Electr ol yte could be spilled on

other par ts and cause cor r osion.

2. Clean the top of the batter y with a paper to w el.

3. R emo v e the v ent caps from the batter y

( Figure 1 ). Slo wly pour electrolyte into eac h

batter y cell until the electrolyte lev el is up to

the Upper line on the batter y case ( Figure 1 ).

Important: Do not o v erﬁll the batter y

because electr ol yte (sulfuric acid) can

cause sev er e cor r osion and dama ge to the

chassis.

Figure 1

1. Vent caps

3. Lower line2. Upper line

4. W ait ﬁv e to ten min utes after ﬁlling the

batter y cells . Add electrolyte , if necessar y , until

the electrolyte lev el is up to the Upper line

( Figure 1 ) on the batter y case .

5. Install the batter y v ent caps .

6. Connect the c harg er leads to the cor responding

batter y posts as sho wn in Figure 2 .

Figure 2

1. Positive Battery Post

3. Red (+) Charger Lead2. Negative Battery Post

4. Black (-) Charger Lead

Charging the batter y pr oduces gasses

that can explode.

Nev er smok e near the batter y and k eep

spar ks and ﬂames a w ay fr om batter y .

7. Charg e the batter y for 10 to 15 min utes at

25 to 30 amps or 30 min utes at 4 to 6 amps

( Figure 2 ). Do not o v erc harg e the batter y .

8. W hen ﬁnished, unplug the c harg er from the

electrical outlet, then disconnect the c harg er

leads from the batter y posts ( Figure 2 ).

Note: Do not r un the mac hine with the

batter y disconnected, electrical damag e ma y

occur .

Step

Connecting the Battery

Parts needed for this step:

Bolt (1/4 x 3/4 inch)

Washer

Nut (1/4 inch)

Procedure

1. Install the batter y in the mac hine and connect

the batter y cables using tw o bolts (1/4 x 3/4

inc h), tw o w ashers , and tw o n uts (1/4 inc h).

R oute the batter y cable from the positi v e

batter y post to the solenoid. Ensure the cable

is routed abo v e the crossbar and betw een the

seat suppor ts as sho wn in Figure 3 .

Figure 3

1. Battery cable 3. To solenoid2. Plastic tie 4. Fuse block

2. Connect the positi v e batter y cable to the

positi v e batter y post using the existing

fasteners .

Important: Connect the ca ble to the

positi v e post so that it extends parallel with

the top of the batter y , as sho wn in Figur e 4 ,

and v erify that it does not come in contact

with the seat pan.

Figure 4

Step

Installing the Seat

Parts needed for this step:

Seat

2 Spacers

Flat washers

Knobs

Procedure

1. R emo v e the seat from the mac hine . Raise the

seat suppor t on the mac hine ( Figure 5 ).

2. Slide the shoulder bolts on the bottom of the

seat into the slots in the seat suppor t ( Figure 5 ).

Figure 5

1. Seat support

2. Shoulder bolt

3. Secure the seat to the seat suppor t with the

spacers , ﬂat w ashers (5/16 inc h) and knobs

( Figure 6 ).

Figure 6

1. Seat

4. Washers (5/16 inch)2. Seat support 5. Spacer3. Knob

Important: Mak e sur e the spacer s

ar e betw een the seat and suppor t, and

the knobs pass thr ough the w asher s,

seat suppor t, spacer s and into the seat

( Figur e 6 ).

4. Connect the seat switc h har ness to the seat

switc h in the base of the seat as sho wn in

Figure 7 .

Figure 7

1. Seat

3. Switch harness2. Seat switch

5. Lo w er the seat and adjust it if necessar y; refer

to P ositioning the Seat in the mo w er Operator’ s

Manual .

Step

Installing the MotionControl Levers

Parts needed for this step:

Control lever

Bolt (1/4 x 3/4 inch)

Procedure

1. R emo v e the motion control lev ers from the

mac hine .

2. P osition the control lev er to the desired height

and align with the holes in the control lev er

shaft ( Figure 8 ).

3. Install 2 bolts (1/4 x 3/4 inc h) into the control

lev er and shaft ( Figure 8 ).

Figure 8

1. Control lever

3.2. Bolt

4. R e peat the installation for the opposite control

lev er .

5. Lo w er the seat and adjust if necessar y; refer to

P ositioning the Seat in the Operator’ s Manual .

Step

Completing the Setup

Parts needed for this step:

Ignition Key

Operator’s Manual

Engine Operator’s Manual

Hose coupling

Operator Training Material

Procedure

Checking the Tir e Pr essur e

Chec k the front and rear tires for proper inﬂation.

R efer to Chec king the Tire Pressure in the Operator’ s

Manual for the recommended inﬂation pressure .

Checking the Mo w er Adjustment

T he mo w er dec k w as lev eled at the factor y . If the

mo w er is not cutting lev el, adjust the side-to-side

lev el and the front-to-rear blade slope . See the

Operator’ s Man ual for the proper procedure .

Checking the Side Discharge Chute

R emo v e the pac king restraint holding the side

disc harg e c hute up and lo w er the c hute into place .

Checking the Engine Oil Lev el

Before y ou star t the engine and use the mac hine ,

c hec k the oil lev el in the engine crankcase; refer to

Chec king the Oil Lev el in the Operator’ s Manual .

R eview the R emaining P ar ts

K ee p all the follo wing items with the mac hine:

•Ignition K ey

•Operator’ s Manual

•Engine Operator’ s Manual

•Hose coupling

•View the Operator training material.

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro 30360 Bedienungsanleitung

Toro

Toro 74904 Bedienungsanleitung

Toro

Toro 39678 Bedienungsanleitung

Toro

Toro Super Recycler 20383 Bedienungsanleitung

Toro

Toro 74279TE Bedienungsanleitung

Toro

Toro Z Master Professional 7000 Series Bedienungsanleitung

Toro

Toro 74142TE Bedienungsanleitung

Toro

Toro 73570 Bedienungsanleitung

Toro

Toro Greensmaster 04251 Bedienungsanleitung

Toro

Toro 73580 Bedienungsanleitung

Toro

Toro 71228 Bedienungsanleitung

Toro

Toro GreensPro 1260 Bedienungsanleitung

Toro

Toro TITAN ZX 4800 Bedienungsanleitung

Toro

Toro 73580 Handbuch

Toro

Toro 70131 Bedienungsanleitung

Toro

Toro 22291 Bedienungsanleitung

Toro

Toro Z593-D Z Master 74264 Bedienungsanleitung

Toro

Toro 22276 Bedienungsanleitung

Toro

Toro Recycler 20332 Bedienungsanleitung

Toro

Toro TimeCutter Z4235 74365 Bedienungsanleitung

Toro

Toro 22285 Bedienungsanleitung

Toro

Toro TITAN ZX5450 Bedienungsanleitung

Toro

Toro 20899 Bedienungsanleitung

Toro

Toro 30373 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

Toro timecutter series Handbuch

Beliebte Rasenmäher Handbücher anderer Marken