Toro Z334 Z Master Handbuch

Form No. 3357-761 Rev A

Z334 or Z340 Z Master® Mowers

Model No. For all Z334 or Z340 International Z Master Mowers

Setup Instructions

Loose PartsUse the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Remove the machine from thecrate.

Bolt (3/8 x 1 inch)

Nut (3/8 inch)

Install the seat lanyard.

Right control lever

Left control lever

Bolt (3/8 x 1 inch) (2 are assembled)

Curved washer (3/8 inch) (2 areassembled)

Install the motion control levers.

No parts required

–

Adding fuel to the machine.

No parts required

–

Charge the battery.

Number 2 general purpose lithiumbase or molybdenum base grease.(Purchase separately.)

1 tube Check the machine for grease.

No parts required

–

Check the engine oil level.

No parts required

–

Prepare the side discharge chute.

No parts required

–

Check the hydraulic oil.

No parts required

–

Check the machine before deliveryto the customer.

Operator’s Manual

Parts Catalog

Engine Owner’s Manual

Registration Card

Safety Video

111

Key 2

Delivering the machine to thecustomer.

Step

Removing the Machine fromthe Crate

No Parts Required

Procedure

1. R emo v e the straps holding the mac hine to the

crate .

2. Chec k the air pressure in the rear tires .

Pressure: 13 psi (90 kP a)

Figure 1

Note: T here is no v alv e stem located in the

front tires , it is a semi-pneumatic tire and does

not need to be c hec k ed.

Step

Installing the Seat Lanyard

Parts needed for this step:

Bolt (3/8 x 1 inch)

Nut (3/8 inch)

Procedure

1. R emo v e the n ut, w asher , and bolt from the

lanyard.

2. Tilt the seat forw ard and align the lanyard to

the hole in the seat base .

3. Install the lanyard to the seat base with a bolt

(3/8 x 1 inc h) and n ut (3/8 inc h).

4. Tilt the seat do wn.

Figure 2

1. Seat base

3. Nut (3/8 inch)2. Bolt (3/8 x 1 inch)

4. Lanyard

5. Chec k the pump dri v e belt idler ar m for g rease

before installing the seat retainer . R efer to Ste p

6, Chec king the Mac hine for Grease , on pag e 4.

6. Install seat retainer brac k et to hold do wn the

seat.

Figure 3

1. Nut

3. Bolt2. Seat retainer bracket

Step

Installing the MotionControl Levers

Parts needed for this step:

Right control lever

Left control lever

Bolt (3/8 x 1 inch) (2 are assembled)

Curved washer (3/8 inch) (2 are assembled)

Procedure

Note: T here are tw o control lev er height options

a v ailable . Install the control lev er in the top tw o

holes for the high position and the bottom tw o

holes for the lo w position.

1. R emo v e the bottom bolt (3/8 x 1 inc h) and

cur v ed w asher (3/8 inc h) from the motion

control lev er . Loosen the upper bolt (3/8 x

1 inc h) and cur v ed w asher (3/8 inc h) that are

installed in the posts .

2. P osition the lev er so the bottom hole aligns

with the hole in the control ar m shaft. Loosely

install the control lev ers to the outside of the

posts .

3. Raise the lev ers to the neutral position and align

them b y sliding them forw ard or bac kw ard and

tighten the bolts .

4. If the ends of the lev ers hit ag ainst eac h when

rotated into the dri v e position, mo v e them to

the neutral position and carefully bend them

outw ard.

5. Mo v e them bac k to the dri v e position and

c hec k for clearance .

6. R e peat if necessar y .

Figure 4

Figure 5

Step

Adding Fuel to the Machine

No Parts Required

Procedure

Note: Mak e sure both fuel tanks are half full

when ﬁrst star ting the mac hine . T his will prev ent

air g etting into the fuel system and causing star ting

problems .

Add fuel to the mac hine before star ting it. R efer

to y our Operator’ s Manual. for the cor rect fuel and

procedure .

Step

Charging the Battery

No Parts Required

Procedure

Charging the batter y pr oduces gasses that

can explode and cause serious injur y .

• K eep cigar ettes, spar ks and ﬂames a w ay

fr om the batter y .

• Mak e sur e the ignition s witch is of f.

• V entilate when charging or using the

batter y in an enclosed space.

Important: Do not r un the machine with

the batter y disconnected; electrical dama ge

may occur to the engine.

Charg e the batter y . R efer to the Operator’ s Manual

for instr uctions .

Figure 6

Step

Checking the Machine forGrease

Parts needed for this step:

1 tube

Number 2 general purpose lithium baseor molybdenum base grease. (Purchaseseparately.)

Procedure

1. Tilt the seat forw ard.

2. Chec k the dec k lift pi v ots for g rease .

3. Chec k the pump dri v e belt idler ar m for g rease .

Figure 7

Step

Checking the Engine OilLevel

No Parts Required

Procedure

Before y ou star t the engine and use the mac hine ,

c hec k the oil lev el in the engine crankcase; refer to

Chec king Oil Lev el in Operator’ s Manual.

Step

Preparing the SideDischarge Chute

No Parts Required

Procedure

1. R emo v e the plastic tie holding the side

disc harg e c hute up and lo w er the c hute into

place .

2. Chec k the spring at the disc harg e c hute to

ensure proper operation.

Figure 8

Step

Checking the Hydraulic Oil

No Parts Required

Procedure

1. Star t the engine and dri v e the mac hine forw ard

and bac kw ard for a few min utes to allo w any

extra air to purg e out of the h y draulic system.

2. P osition the mac hine on a lev el surface .

3. Diseng ag e the PTO , mo v e the motion control

lev ers to the neutral loc k ed position, and set

the parking brak e .

4. Stop the engine , remo v e the k ey , and w ait for

all mo ving par ts to stop before lea ving the

operating position.

5. Chec k the expansion tank behind the seat and

if necessar y add h y draulic oil to the cold line

on the side of the tank.

6. R e place the tank cap , but do not o v er tighten.

Figure 9

1. Cap

3. Cold uid level-full2. Hot uid level-full

Step

Checking the Machine Before Delivery to the Customer

No Parts Required

Procedure

Before deli v ering the mac hine to the customer , ensure that y ou perfor m or ha v e perfor med the

procedures listed in the follo wing table and initial eac h when ﬁnished. R efer to the Operator’ s Man ual

for instr uctions on perfor ming these procedures .

Initial

Check Procedure

Check the tire pressure.

Check the level of the mower.

Check the engine oil level.

Check the hydraulic uid level.

Check the operation of the parking brake.

Ensure that the machine tracks correctly; refer to the Operator’s Manual for the adjustmentprocedure.

Check the safety interlock system; refer to the Operator’s Manual .

Ensure that the PTO works.

Check all fasteners you installed to ensure that they are tight.

W hen y ou ﬁnish setting up the mac hine , sign and date in the space pro vided belo w:

Signature: Date:

Step

Delivering the Machine to the Customer

Parts needed for this step:

Operator’s Manual

Parts Catalog

Engine Owner’s Manual

Registration Card

Safety Video

2 Key

Procedure

At deli v er y , complete the items listed in the follo wing table and initial eac h when ﬁnished.

Model No. Serial No.

Dealer Initial Customer Initial Check Procedure

Show the customer where the following features are located and howthey function:

Fuel tank caps

Oil ll cap/ Oil dipstick

Engine oil lter

Engine oil drain

Fuel lters

Air lter

Hydraulic uid reservoir

Hydraulic lters

Battery

Ignition switch

Throttle lever

Choke lever

Power take off switch (PTO)

Motion control levers

Parking brake

Mower height-of-cut

Adjustable seat

Hydraulic bypass valves

Refer to the Operator’s Manual to point out safety procedures, operation,and maintenance procedures.

Review the warranty statement as shown in the Operator’s Manual.

Describe the post sale service procedures for your store.

Assist the customer in lling out and mailing the registration card orregister online at www.Toro.com

Make sure that the customer receives the Operator’s Manual, Parts Catalog,and Engine Owner’s Manual, Set Up Instructions, and safety video.

Assist the customer in loading the mower.

Note: W hen y ou, the dealer re presentati v e , ha v e ﬁnished deli v ering the mac hine to the customer , sign

and date in the space pro vide belo w and k ee p a copy of this pag e for dealer records .

Signature: Date:

Andere Handbücher für Z334 Z Master

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro timecutter series Handbuch

Toro

Toro 79410 Bedienungsanleitung

Toro

Toro 30569 Bedienungsanleitung

Toro

Toro reelmaster 216 Bedienungsanleitung

Toro

Toro Super Recycler 20054 Bedienungsanleitung

Toro

Toro 30403 Bedienungsanleitung

Toro

Toro 22155TE Bedienungsanleitung

Toro

Toro Super Recycler 20837 Bedienungsanleitung

Toro

Toro 26634 Bedienungsanleitung

Toro

Toro Greensmaster Flex 18 04018 Bedienungsanleitung

Toro

Toro 4380 Bedienungsanleitung

Toro

Toro 75742 Bedienungsanleitung

Toro

Toro Z Master Professional 7500-DSeries Handbuch

Toro

Toro 22157 Bedienungsanleitung

Toro

Toro GrandStand 74534 Bedienungsanleitung

Toro

Toro Z Master 3000 SERIES Bedienungsanleitung

Toro

Toro 29641 Bedienungsanleitung

Toro

Toro TimeCutter MX 4275 Bedienungsanleitung

Toro

Toro TimeCutter SW 4200 Bedienungsanleitung

Toro

Toro Recycler 20954 Bedienungsanleitung

Toro

Toro 30435 Bedienungsanleitung

Toro

Toro Groundsmaster 5900 Bedienungsanleitung

Toro

Toro 03480 Bedienungsanleitung

Toro

Toro Z Master Professional 5000 Series Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung