Toshiba B-SX6T Series Bedienungsanleitung

TOSHIBA Thermal Printer

B-SX6T/SX8T Series

SUPPLY LOADING INSTRUCTIONS

This sheet contains only the media and ribbon loading procedures. Please be sure to read the Owner’s Manual in

the CD-ROM for further information about this printer.

1. LOADING THE MEDIA

The following procedure shows the steps to properly load the media into the printer so that it feeds straight and

true through the printer.

The printer prints both labels and tags.

1. Install one of the Media Holders onto the Supply Shaft.

Turn the Locking Lever of the Media Holder to “Close” position to fix the Supply Shaft with the Media

Holder.

2. Place a media roll onto the Supply Shaft and push the media against the Media Holder.

1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the

moving parts, be sure to load the media once the printer has stopped moving completely.

2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the media.

3. Care must be taken not to pinch your fingers when opening or closing the Top Cover or Right Side

Cover.

4. Be careful not to pinch your fingers by the Supply Holder Frame or Media Holders when loading the media.

AVERTISSEMENT!

1. Ne touchez pas aux éléments en mouvement. Pour éviter les risques que les doigts, les bijoux les habits,

etc. soient tirés vers les éléments en mouvement, rassurez-vous de charger le média lorsque l'imprimante

est arrêtée complètement.

2. La tête chauffe beaucoup en imprimant. Laissez-la refroidir avant de charger le média.

3 .Prenez garde à ne pas vous pincer les doigts lorsque vous manipulez la capot supérieur ou le capot

coté droit.

4. Prenez garde à ne pas vous pincer les doigts lorsque vous manipulez le cadre support média ou les

guides lors du chargement média.

WARNING!

Supply Shaft

Media Holde

Locking

Leve

Media

Supply Shaf

Close Open

!00TSCC0167811!

3. Install the other Media Holder onto the Supply Shaft from the opposite side.

Turn the Locking Lever of the Media Holder to the “Close” position.

4. Set the Head Lever to the “OPEN” position.

5. Open the Top Cover and the Right Side Cover.

Open the Head Lock Plate (), and turn the Pinch Roller Lever clockwise () to release the Pinch Roller.

6. Loosen the Media Guide Screws on the printer back, and move the Media Guides outside.

Media Holder

Supply Shaft

Locking Leve

“Close” Position

Media

Head Lever

“OPEN” position

Top Cover

Right Side Cover

Head Lock Plate

Pinch Roller

Lever





Media Guide Scre

Media Guide

Supply Holder

Frame

7. Place the assembled Media Holder onto the Supply Holder Frame, and feed the media between the two Media

Guides.

Turn the Locking Lever of the Media Holder to the “Open” position, and push the Media Holders toward the

centre to place the media at the centre on the Supply Shaft. Then, lock the position of the media by returning the

Locking Levers to the “Close” position.

8. Feed the media until it extends past the Platen.

9. Move the Media Guides inside, causing the media to be automatically centred. Then, tighten the Media Guide

Screws to secure the Media Guides.

Media

Media Holder Frame

Locking Leve

Close Open

NOTE:

Place the bushes of the Supply Shaft into the

notches of the Supply Holder Frame securely.

Bush

Notch

Media Guide

Media Guide Scre

Media

Be careful not to pinch your fingers or hands by the Supply Holder Frame or Media Holders when

loading the media. AVERTISSEMENT!

Prenez garde à ne pas vous pincer les doigts lorsque vous manipulez le cadre support média ou les

guides lors du chargement média.

WARNING!

10. After loading the media, it may be necessary to set the position of the Media Sensor used to detect the print

start position for label or tag printing.

This printer is equipped with two media sensors: Fixed sensor and Movable sensor. Each of them is

comprised of a Feed Gap Sensor and a Black Mark Sensor.

Fixed sensor: This sensor is positioned at the centre of the printer unit. It is intended for detecting gaps

between labels or black marks marked at the centre.

Movable sensor: The position of this sensor is adjustable. It is intended for detecting gaps between labels,

black marks, notches, etc. that are not positioned at the centre of the media.

Detail of Movable Sensor Detail of Fixed Sensor

Movable Sensor Fixed Sensor

Black Mark Sensor Position

Feed Gap Sensor Position

NOTES:

1 When using the Movable sensor, choose the Movable sensor for the parameter setting in the system mode.

The Fixed sensor has been selected as default.

2. The position of the movable sensor should be adjusted before loading the ribbon. Otherwise, the sensor is

covered by the ribbon, causing the sensor position adjustment to be disabled.

The following procedures show how to adjust the position of the movable sensor.

Feed Gap Sensor position adjustment

When using a label stock without black marks, the Feed Gap Sensor is used to detect the print start position.

Looking inside of the Media Outlet, move the Movable Sensor by rotating the Adjustment Knob until the Feed

Gap Sensor aligns with a gap. (The right side hole indicates the position of the Feed Gap Sensor.)

Black Mark Sensor position adjustment

When using media with black marks, the Black Mark Sensor is used to detect the print start position.

(1) Pull the media about 500 mm out of the front of the printer, turn the media back on it’s self and feed it under the

print head.

(2) Move the Movable Sensor by rotating the Adjustment Knob, until the Black Mark Sensor aligns with a black

mark. (The left side hole indicates the position of the Black Mark Sensor).

Media Outlet Adjustment Knob

Left side hole:

Black Mark Senso

Right side hole:

Feed Gap Sensor

Forward

Backward

Media

Black Mar

Left side hole:

Black Mark Senso

Right side hole:

Feed Gap Sensor

Forward

Backward

Adjustment Knob

NOTE: Be sure to set the Black Mark Sensor to detect the centre of the black mark, otherwise a paper jam or no

paper error may occur.

11. There are three issue modes available on this printer. How to set the media for each mode is provided below.

In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue

command have been printed.

(1) Pull the media past the media outlet.

Turn the Pinch Roller Lever counterclockwise to lock the Pinch Roller.

(2) Close the Top Cover and Right Side Cover.

When the optional Strip Module is fitted, a label is automatically removed from the backing paper at the Strip

Plate as each label is printed.

(1) Pull out the backing paper past the Media Outlet.

(2) While holding down the Backing Paper Release Bar, and pass the backing paper between the Backing Paper

Holder and the Strip Roller. Then, release the Backing Paper Release Bar.

(3) Turn the Pinch Roller Lever counterclockwise to lock the Pinch Roller.

Close the Top Cover and Right Side Cover.

Batch mode

Stri

mode

(

tion

)

Media Outlet

Pinch Roller Lever

Media Outlet

Backing Pape

Release Ba

Backing Paper

Backing Pape

Strip module

Strip Roller

Backing Paper

Holder

Pinch Roller Lever Right Side Cover

Top Cover

When the Backing Paper Release Bar is released, it is

automatically closed by the spring. Care must be

taken not to pinch your fingers or hands.

ATTENTION!

Lorsque vous relâchez la barre du contre rouleau, un

ressort la ramène automatiquement en position.

Attention de ne pas vous faire pincer les doigts ou

les mains.

WARNING!

When the optional Cutter Module is fitted, the media is automatically cut.

(1) Insert the leading edge of the media into the Media Outlet of the Cutter Module.

(2) Turn the Pinch Roller Lever counterclockwise to lock the Pinch Roller.

Close the Top Cover and Right Side Cover

12. Change the print head pressure according to the thickness of the media to be used, by using the Head Lever.

13. If the loaded media is direct thermal media (with a chemically treated surface), the media loading procedure

is now completed.

If the media is normal media, it is also necessary to load a ribbon.

Cut mode

(

tion

)

Cutter module

Position Media type or thickness

Label or Thin media

If a clear print cannot be

obtained, change the position

to .

Tag paper or Thick pape

If a clear print cannot be

obtained, change the position

to .

The cutter is sharp, so care must be taken not to injure your

fingers when handling the cutter.

AVERTISSEMENT!

Le massicot présente des parties coupantes, prenez garde

à ne pas vous blesser en le manipulant

WARNING!

CAUTION!

1. When using a label stock, be sure to cut the gaps. Cutting

labels will cause the glue to stick to the cutter, which may

affect the cutter quality and shorten the cutter life.

2. Use of tag paper which thickness exceeds specified value

may affect the cutter life.

ATTENTION!

1. Assurez vous de massicoter les étiquettes sur l’échenillage. Si

vous massicotez l’étiquette, de la colle risque de s’accumuler

sur la lame du massicot, affectant la qualité et la durée de vie

de ce dernier.

2. L’utilisation de cartonnette dont l’épaisseur excède les

spécifications peut réduire la durée de vie du massicot.

Pinch Rolle

Leve

Head Lever

2. LOADING THE RIBBON

There are two types of media available for printing on: these are thermal transfer media (normal media) and

direct thermal media (with a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal

media.

1. Set the Head Lever to the “OPEN” position.

Open the Top Cover, Right Side Cover, and the Head Lock Plate.

2. Leaving plenty of slack between the ribbon spools, insert the ribbon under the Print Block.

1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being drawn into the

moving parts, be sure to load the ribbon once the printer has stopped moving completely.

2. The print head becomes hot immediately after printing. Allow it to cool before loading the ribbon.

3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.

AVERTISSEMENT!

1. Ne touchez pas aux éléments en mouvement. Pour éviter les risques que les doigts, les bijoux les habits,

etc. soient tirés vers les éléments en mouvement, rassurez-vous de charger le média lorsque l'imprimante

est arrêtée complètement.

La tête chauffe beaucoup en imprimant. Laissez-la refroidir avant de charger le média.

3. Pour éviter les blessures, faites attention de ne pas vous pincer les doigts en ouvrant ou en fermant le

capot.

WARNING!

CAUTION!

Be careful not touch the Print Head Element when opening the Top Cover. Failure to do this may cause missing

dots by static electricity or other print quality problems.

ATTENTION!

Faites attention de ne pas toucher la tête d’impression en ouvrant le capot supérieur. De l’électricité statique

pourrait endommager la tête ou entraîner des problèmes de qualité d’impression.

Head Lever

“OPEN”

position

Head Lock

Plate

Right Side

Cover

Top Cover

Ribbon Supply Roll

Print Block

Ribbon Take-up Roll

Ribbon Holder (Supply Side)

Ribbon Holder (Take-up Side)

NOTE: Do not change the Ribbon Holder

Adjustment Lever positions. Doing so will

changed the adjustment. If you moved them

accidentally, return the positions to the centre.

Ribbon Holder Adjustment Lever

3. Fit the core of the Ribbon Supply Roll into the Ribbon Holders (Supply side), aligning the notch of the ribbon

core with the protrusion of the Ribbon Holder.

4. Fit the core of the Ribbon Take-up Roll into the Ribbon Holders (Take-up side), aligning the notch of the

ribbon core with the protrusion of the Ribbon Holder.

5. Take up any slack in the ribbon. Wind the leading tape onto the ribbon take-up roll until the ink ribbon can be

seen from the front of the printer.

6. Close the Head Lock Plate, Right Side Cover, and Top Cover.

Turn the Head Lever to the Position 1 or 2.

Ribbon Holder (Supply Side)

Ribbon Supply Roll

Notch

Ribbon Core

Fit the protrusion

into the notch.

Ribbon Supply Roll

Ribbon Take-up Roll

NOTE: Be sure to remove any slack in the ribbon when printing. Printing with a wrinkled ribbon will lower

the print quality.

Ribbon Holder (Take-up Side)

Ribbon Take-up Roll

Fit the

protrusion into

the notch.

“Open” Position

NOTES:

1. When a ribbon end is detected, “RIBBON ERROR” message will appear on the display and the ERROR LED

will illuminate.

2. When disposing of the ribbons, please follow the local rules.

3. When using a non transparent ribbon, choose the Non trans ribbon for the parameter setting in the system mode.

Transparent ribbon has been selected as default.

Right Side Cover

Top Cover

Head Lock Plate

Head Leve

2: Tag paper or Thick pape

1: Label or Thin media

PRINTED IN INDONESIA

EO2-33023D

SPTM-0234

1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN

Andere Handbücher für B-SX6T Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba e-STUDIO 305CP Bedienungsanleitung

Toshiba

Toshiba B-570-QQ Bedienungsanleitung

Toshiba

Toshiba B-450-R SERIES Bedienungsanleitung

Toshiba

Toshiba B-EP2DL Series Bedienungsanleitung

Toshiba

Toshiba SureMark Bedienungs- und Sicherheitshinweise

Toshiba

Toshiba B-SV4D Series Bedienungsanleitung

Toshiba

Toshiba 1TN Bedienungsanleitung

Toshiba

Toshiba E-studio18 Originalbetriebsanleitung

Toshiba

Toshiba 4679 Bedienungsanleitung

Toshiba

Toshiba B-FP3D-GH30-QM-R Bedienungsanleitung

Toshiba

Toshiba HSP100 Bedienungs- und Wartungsanleitung

Toshiba

Toshiba 7FM03281000 Bedienungsanleitung

Toshiba

Toshiba B-EP Series Bedienungsanleitung

Toshiba

Toshiba B-SA4TM SERIES Bedienungsanleitung

Toshiba

Toshiba B-SA4T Bedienungsanleitung

Toshiba

Toshiba B-EP4DL Series Bedienungsanleitung

Toshiba

Toshiba B-EX4 SERIES Bedienungsanleitung

Toshiba

Toshiba GA-1310 Bedienungsanleitung

Toshiba

Toshiba B-SA4TP SERIES Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 452 Konfigurationshandbuch

Toshiba

Toshiba e-STUDIO2010AC Bedienungsanleitung

Toshiba

Toshiba B-EX4 T1 Series Technische Daten

Toshiba

Toshiba B-SX6T Series Bedienungsanleitung

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung