Toshiba MK8016GSG Kurzanleitung

MK**16GSG Hard Disk Drive Installation Notes P/N 480097-A0 P/N 480097-A0 MK**16GSG Hard Disk Drive Installation Notes

04/08 04/08

TOSHIBA STORAGE DEVICE DIVISION

MK**16GSG Series

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK1216GSG (HDD1F01) and MK8016GSG (HDD1F02) hard disk drive’s

integrate the Serial ATA interface and 5400 RPM rotational speed into a compact, 1.8-

inch footprint, furthering the evolution of mobile PCs into smaller and performance-

enhanced, ultra-portable systems.

SPECIFICATIONS MK1216GSG MK8016GSG

HDD1F01 HDD1F02

FORMATTED CAPACITY 120GB 80GB

HEIGHT 8mm 8mm

WEIGHT 62g 62g

NO. OF DISKS (PLATTERS) 2 2

NO. OF DATA HEADS 4 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK1216GSG/MK8016GSG

PARAMETERS HDD1F01/HDD1F02

NO. OF CYLINDERS (user) 79,488

BYTES PER SECTOR 512

BUFFER SIZE 8MB

ROTATION SPEED (±0.1%) 5,400rpm

TRANSFER RATE INTERNAL 227 - 489Mbits/sec (typical)

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE 1.5Gbits/sec

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 131°F (5°C - 55°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Serial ATA connector:

Signal Segment Key

S1 GND 2nd mate

S2 A+ Differential Pair A from PHY

Signal S3 A-

Segment S4 GND

S5 B- Differential Pair B from PHY

S6 B+

S7 GND 2nd mate

Signal Segment “L”

Central Connector Polarizer

Power Segment “L”

P1 V33 3.3V Power

P2 V33 3.3V power pre-charge

P3 GND

Power P4 GND

Segment P5 V5 5V Power pre-charge 2nd mate

P6 V5 5V power

P7 Reserved*

P8 Optional

P9 Optional

Power Segment Key

* The corresponding pin to be mated with pin P7 in the power Internal Micro receptacle.

Connector shall always be grounded.

Notice: this drive uses 3.3V power only. 5V power is not used.

MK**16GSG Hard Disk Drive Installation Notes P/N 480097-A0 P/N 480097-A0 MK**16GSG Hard Disk Drive Installation Notes

04/08 04/08

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

When connecting the drive and host system with Serial ATA cable, use of a Serial ATA

2.6 specification compliant cable is recommended.

Drive Side Connector DDK: SAT-PF16-S1A-FG

Recommended host side FPC Right Angle Type:

DDK SAT-RH16-S1B-FA or equivalent

FIGURE 1 – INTERFACE CONNECTOR

TECHNICAL SUPPORT

Should you require technical support, contact your computer distributor. If your dis-

tributor is unable to answer your questions, have them call Toshiba Storage Device

Division Technical Support, on your behalf.

TOSHIBA - STORAGE DEVICE DIVISON TECHNICAL SUPPORT

PHONE: 510/651-6798 FAX: 510/623-9893

EMAIL: [email protected]

You can also visit Toshiba’s web site at: http://www.toshibastorage.com

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK**16GSG Hard Disk Drive Installation Notes P/N 480097-A0 P/N 480097-A0 MK**16GSG Hard Disk Drive Installation Notes

04/08 04/08

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

When connecting the drive and host system with Serial ATA cable, use of a Serial ATA

2.6 specification compliant cable is recommended.

Drive Side Connector DDK: SAT-PF16-S1A-FG

Recommended host side FPC Right Angle Type:

DDK SAT-RH16-S1B-FA or equivalent

FIGURE 1 – INTERFACE CONNECTOR

TECHNICAL SUPPORT

Should you require technical support, contact your computer distributor. If your dis-

tributor is unable to answer your questions, have them call Toshiba Storage Device

Division Technical Support, on your behalf.

TOSHIBA - STORAGE DEVICE DIVISON TECHNICAL SUPPORT

PHONE: 510/651-6798 FAX: 510/623-9893

EMAIL: [email protected]

You can also visit Toshiba’s web site at: http://www.toshibastorage.com

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK**16GSG Hard Disk Drive Installation Notes P/N 480097-A0 P/N 480097-A0 MK**16GSG Hard Disk Drive Installation Notes

04/08 04/08

TOSHIBA STORAGE DEVICE DIVISION

MK**16GSG Series

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK1216GSG (HDD1F01) and MK8016GSG (HDD1F02) hard disk drive’s

integrate the Serial ATA interface and 5400 RPM rotational speed into a compact, 1.8-

inch footprint, furthering the evolution of mobile PCs into smaller and performance-

enhanced, ultra-portable systems.

SPECIFICATIONS MK1216GSG MK8016GSG

HDD1F01 HDD1F02

FORMATTED CAPACITY 120GB 80GB

HEIGHT 8mm 8mm

WEIGHT 62g 62g

NO. OF DISKS (PLATTERS) 2 2

NO. OF DATA HEADS 4 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK1216GSG/MK8016GSG

PARAMETERS HDD1F01/HDD1F02

NO. OF CYLINDERS (user) 79,488

BYTES PER SECTOR 512

BUFFER SIZE 8MB

ROTATION SPEED (±0.1%) 5,400rpm

TRANSFER RATE INTERNAL 227 - 489Mbits/sec (typical)

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE 1.5Gbits/sec

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 131°F (5°C - 55°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Serial ATA connector:

Signal Segment Key

S1 GND 2nd mate

S2 A+ Differential Pair A from PHY

Signal S3 A-

Segment S4 GND

S5 B- Differential Pair B from PHY

S6 B+

S7 GND 2nd mate

Signal Segment “L”

Central Connector Polarizer

Power Segment “L”

P1 V33 3.3V Power

P2 V33 3.3V power pre-charge

P3 GND

Power P4 GND

Segment P5 V5 5V Power pre-charge 2nd mate

P6 V5 5V power

P7 Reserved*

P8 Optional

P9 Optional

Power Segment Key

* The corresponding pin to be mated with pin P7 in the power Internal Micro receptacle.

Connector shall always be grounded.

Notice: this drive uses 3.3V power only. 5V power is not used.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Lagerung Handbücher

Toshiba

Toshiba MK3019GAX Bedienungsanleitung

Toshiba

Toshiba HDD1544 Bedienungsanleitung

Toshiba

Toshiba MK2016GAP Bedienungsanleitung

Toshiba

Toshiba MK3017GAP Bedienungsanleitung

Toshiba

Toshiba MK1234 Kurzanleitung

Toshiba

Toshiba MK6017MAP Betriebsanleitung

Toshiba

Toshiba microSDHC Bedienungsanleitung

Toshiba

Toshiba MK6411MAT Bedienungsanleitung

Toshiba

Toshiba PH3064U-1EXB Bedienungsanleitung

Toshiba

Toshiba PX02SMF020 Bedienungsanleitung

Toshiba

Toshiba HDD2166 Bedienungsanleitung

Toshiba

Toshiba MK1032GAX Bedienungsanleitung

Toshiba

Toshiba MK5002MPL Bedienungsanleitung

Toshiba

Toshiba G9000 SERIES Bedienungsanleitung

Toshiba

Toshiba MK6034GAX Series Kurzanleitung

Toshiba

Toshiba Canvio AeroCast Bedienungsanleitung

Toshiba

Toshiba W7 Series Bedienungsanleitung

Toshiba

Toshiba STORE alu Bedienungsanleitung

Toshiba

Toshiba MK2556GSY Bedienungsanleitung

Toshiba

Toshiba MK2565GSX Konfigurationshandbuch

Toshiba

Toshiba PH3100U-1EXB Handbuch

Toshiba

Toshiba MK1016GAP Bedienungsanleitung

Toshiba

Toshiba CANVIO BASICS Bedienungsanleitung

Toshiba

Toshiba MK5002MAL Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung