TOTALINE CPE230RF Bedienungsanleitung

Part Number P474-2300RF

CONTENTS Page

GENERAL .......................................... 2

CONFIGURATION ....................................3-12

Transmitter Display .................................. 3

Transmitter Indicator ................................. 3

Transmitter Front Panel Buttons ....................... 4

Set Clock ........................................... 7

Programming Thermostat Schedules .................... 7

OPERATION .........................................13

Auto-Changeover .................................... 13

Electric Heat ........................................ 13

Dry Contact Switch/External Device .....................13

Two-Stage Operation ..................................13

Fan Operation .......................................13

IMPORTANT: Read entire instructions before programming the

thermostat.

OWNER’S

MANUAL CPE230RF

Commercial

Programmable Thermostat

Wireless Transmitter

Manufacturer reserves the right to

discontinue, or change at any time,

speciﬁcations or designs without notice

and without incurring obligations.

REPLACEMENTCOMPONENTSDIVISION

RCARRIER CORPORATION 10/98

LITERATURE NUMBER P474-6SO

PRINTED IN CHINA

GENERAL

The 7-day, commercial, programmable thermostats maintain room tem-

perature by controlling the operation of your heating, cooling, and ventilation

system. Separate heating and cooling set points and auto-changeover capa-

bility allow you to program schedules for energy savings.

All thermostats allow up to 4 time/temperature settings to be programmed

per 24-hr period. Each thermostat stores programs for 7 independent days.

Batteries are required for operation. During power interruption (batteries re-

moved) the internal NEVERLOST™ memory stores conﬁguration programs

for an unlimited time. The clock will need to be reset every time power is lost

(batteries removed).

The wall mounted or hand-held transmitter sends its signal to a receiver

installed near the HVAC unit. Each paired transmitter and receiver can be

given a separate house code for multiple thermostat applications. Up to

4 transmitters can send information to 1 receiver device.

If more than one transmitter is used with a single receiver, the transmitters

must be given different Unit ID Numbers. Only the transmitter with Unit ID

Number 1 may have a programmed schedule or be conﬁgured. All conﬁgu-

ration parameters are taken from the transmitter with Unit ID Number 1. Trans-

mitters with Unit ID Numbers 2, 3, and 4 cannot be programmed or conﬁg-

ured (except for set points).

When more than one transmitter is used, the receiver will only accept com-

mands from the transmitter that was last used (button pressed). All other set

points and modes from other transmitters are ignored. If the transmitter with

Unit ID Number 1 has a schedule and is in Program On mode, the receiver

will revert back to following the programmed schedule when a time period

change occurs, even if the transmitter with Unit ID Number 1 is not the cur-

rent commanding transmitter.

IMPORTANT: The transmitter has a conﬁgurable security level. If certain

functions are not available (changing set points, changing programming

schedules), the transmitter security level may be conﬁgured to exclude those

functions. Call the installer to reconﬁgure the security level.

CONFIGURATION

Transmitter Display — The transmitter display is located in the center of

the transmitter. See Fig. 1. The following information can be displayed on the

screen:

• mode (OFF, HEAT, COOL, AUTO, or PROGRAM ON)

• fan setting (FAN ON or blank)

• override indication

• room temperature

• desired temperature

• time of day

• day of the week

• schedule period (Occupied 1, 2, or 3; Unoccupied)

• setup indicator (used in programming mode)

• lock indicator

• start indicator (used in programming mode)

Transmitter Indicator — A transmitter indicator is located in the middle

of the transmitter. See Fig. 2. The indicator will be lit if the transmitter is

sending a signal to the receiver.

Transmitter Front Panel Buttons — The transmitter has buttons which

are used to raise or lower the desired set point and change the mode. See

Fig. 2.

SET POINT BUTTONS — The UP ARROW and DOWN ARROW buttons

will raise or lower the current desired temperature set point. The thermostat

will turn on heating or cooling to meet the heating or cooling temperature set

point.

If the thermostat is in AUTO mode, pressing the UP ARROW or DOWN

ARROW buttons will adjust both the heating and cooling set points.

Pressing the UP ARROW or DOWN ARROW buttons in Cooling mode

will adjust only the cooling set points.

Pressing the UP ARROW or DOWN ARROW buttons in Heating mode

will adjust only the heating set points.

The UPARROW and DOWN ARROW buttons are also used in Program-

ming mode.

Fig.1—Transmitter Display

MODE BUTTON — The Mode button selects the operating mode of the

thermostat.

• If OFF is selected, the thermostat will not enter Heating or Cooling mode.

• If HEAT is selected, the thermostat will only enter Heating mode (if the

room temperature is below the heating set point). The thermostat will not

provide cooling.

• If COOL is selected, the thermostat will only enter Cooling mode (if the

room temperature is above the cooling set point). The thermostat will not

provide heating.

• If AUTO is selected, the thermostat will enter Heating or Cooling mode

based on the room temperature and the heating and cooling set points. The

thermostat will provide automatic changeover from Heating to Cooling mode

and Cooling to Heating mode when required. The thermostat will auto-

matically switch to maintain the desired temperature setting. The ther-

mostat does not need to be manually changed from heating to cooling or

cooling to heating operation.

• If PROGRAM ON is selected, your daily schedule is enabled and the ther-

mostat will follow the programmed daily schedule stored in its memory.

NOTE: Only the transmitter with Unit ID Number 1 may have a programmed

schedule.

MODE

OVER

AUTO

COOL

HEAT

BACKLIT LCD DISPLAY

TRANSMITTER INDICATOR

WARMER OR + BUTTON

COOLER OR - BUTTON

MODE BUTTON

OVERRIDE BUTTON RIDE

Fig. 2 — Thermostat Front Panel Buttons

KEYPAD LOCK — The thermostat has a keypad lockout feature which will

not allow anyone to change the settings of your thermostat unless the correct

button sequence is pressed. To disable or lock the keypad, press and hold the

Mode button. While holding down the Mode button, press the UPand DOWN

ARROW buttons simultaneously. The ‘‘Locked’’ icon will appear on

the display.

The thermostat is unlocked by performing the same procedure. Press and

hold the Mode button. While holding down the Mode button, press the UP

and DOWN ARROW buttons simultaneously. The ‘‘Locked’’ icon will be

removed from the display.

PROGRAM — The Mode and UPARROW buttons are used to set the daily

schedules for the thermostat to follow. Refer to the Programming Thermostat

Schedules section on page 7 for more information.

SET CLOCK — The Mode and Override buttons are used to set the ther-

mostat time of day and day of the week. Refer to the Set Clock section on

page 7 for more information.

OVERRIDE BUTTON — The Override button is used to force the thermo-

stat from Unoccupied mode into the Occupied 1 mode comfort settings. The

Override period will be set at 30 minutes. The thermostat will then return to

Unoccupied mode. To increase the amount of time in Override mode, press

the Override button again. Thirty minutes of override time will be added for

each time the Override button is pressed up to a maximum of 4 hours. After

the 4-hour limit has been reached, press the Override button again to cancel

Override mode.

While in Override mode, the Override icon and the Occupied 1 icon will

be displayed on the thermostat. The time of day and the minutes remaining

in Override mode will alternate on the thermostat display.

The set points are adjustable with the UP ARROW and DOWN ARROW

keys during Override mode.

NOTE: If the thermostat is in Occupied mode and the Override button is

pressed, the thermostat will go into Unoccupied mode immediately. The ther-

mostat will remain in Unoccupied mode until the next Occupied start time.

Set Clock — The Mode and Override buttons allow you to change the

time and day displayed on the thermostat.

To set the clock, press and hold the Mode and Override buttons for 2 sec-

onds. See Fig. 3. The display will show the Setup annunciator. The current

time will blink on and off. Press the UP ARROW or DOWN ARROW but-

tons until the correct time is shown. Hold down the buttons to quickly move

through the time display. Hold down the Override button while pressing UP

or DOWN ARROW to change the time by hours. The AM and PM annun-

ciators will automatically change. To ensure the schedules are properly fol-

lowed, make sure that AM or PM is correct for the time chosen.

When the correct time is shown, press the Mode button to modify the day

of the week. The current day will blink on and off. Press the UPARROW and

DOWN ARROW buttons until the correct day is shown. Press and hold the

Mode and Override buttons for 2 seconds again to exit the Set Clock mode.

The transmitter will return to normal operating mode after 60 seconds if

no buttons are pressed.

Programming Thermostat Schedules — Before programming the

thermostat, plan the thermostat daily schedule. The schedule is divided

into 7 days (Monday through Sunday). Each day can have 2 (Occupied 1,

Unoccupied), 3 (Occupied 1, Occupied 2, Unoccupied), or 4 (Occupied 1,

Fig. 3 — Setting the Clock

Occupied 2, Occupied 3, Unoccupied) time periods. Each occupied time pe-

riod has a start time, stop time, heating set point, and cooling set point. The

unoccupied time period has a heating set point and a cooling set point.

The unoccupied time period is active whenever an occupied time period is

not active. Fill in Table 1 on page 12 as an aid to programming the daily

schedules.

PROGRAMMING MODE — To program the daily schedules, perform the

following procedure:

1. Enter programming mode by pressing the Mode and UP ARROW but-

tons at the same time. The Occupied 1 annunciator will appear on the

thermostat display. See Fig. 5. Use the UP ARROW and DOWN AR-

ROW buttons to set the maximum number of Occupied periods avail-

able. The thermostat can be set to 1, 2, or 3. After the number of Oc-

cupied periods has been selected, press the Mode button.

2. The cooling set point for Occupied 1 will be displayed. Use the UPAR-

ROW and DOWN ARROW buttons to raise or lower the cooling set

point until the desired temperature is shown. The range of acceptable

values is 35 to 99 F (1 to 37 C). Press the Mode button to continue. See

Fig. 4.

Fig. 4 — Setting Occupied 1 Set Points

3. The heating set point for Occupied 1 will be displayed. Use the UPAR-

ROW and DOWNARROW buttons to raise or lower the heating set point

until the desired temperature is shown. The range of acceptable values

is 35 to 99 F (1 to 37 C). Press the Mode button to continue. See Fig. 4.

4. The cooling set point for Unoccupied will be displayed. Use the UPAR-

ROW and DOWN ARROW buttons to raise or lower the cooling set

point until the desired temperature is shown. The range of acceptable

values is 35 to 99 F (1 to 37 C) or ‘‘OF’’(no unoccupied cooling). To set

the value to ‘‘OF’’, press the UP ARROW button when ‘‘99’’ is dis-

played. Press the Mode button to continue.

5. The heating set point for Unoccupied will be displayed. Use the UPAR-

ROW and DOWNARROW buttons to raise or lower the heating set point

until the desired temperature is shown. The range of acceptable values

is 35 to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied heating). To set the

value to ‘‘OF’’, press the UP ARROW button when ‘‘99’’ is displayed.

Press the Mode button to continue.

6. The day of the week will be shown. Use the UP ARROW and DOWN

ARROW buttons to change the day of the week until the desired starting

day is shown. Possible choices are M (Monday) through S (Sunday).

Press the Mode button when the desired day is shown.

7. The Start Time for Occupied 1 will be displayed. Use the UP ARROW

and DOWN ARROW buttons to raise or lower the time until the desired

Start Time is shown. Press the Mode button to continue. See

Fig. 5.

8. The Stop Time for Occupied 1 will be displayed. Use the UP ARROW

and DOWN ARROW buttons to raise or lower the time until the desired

Stop Time is shown. Press the Mode button.

9. The On/Off icon will be displayed. Use the UP ARROW to turn the Oc-

cupied 1 period ON for this day. Use the DOWN ARROW to turn the

Occupied 1 period OFF for this day. If the schedule is set to OFF, the

thermostat will follow the Unoccupied set points.

10. Repeat Steps 2 through 9 to program the remaining schedule for occu-

pied periods 2 and 3 (if selected in Step 1).

11. The Copy command can be used to copy the previous day’s schedule if

the schedules are the same. The copy command becomes available after

all the occupied periods are programmed in a day. Use the UP ARROW

to change the copy command toYES. Use the DOWNARROW to change

the copy command to NO. Press the Mode/Next button when the choice

has been made. See Fig. 6.

If NO was selected, the schedule will automatically change to the next

day and the user must enter the occupied and unoccupied schedules for

that day.

NOTE: Occupied 1 schedule heating and cooling set points are the same

for each day. Occupied 2 and 3 set points may be set to different values

for each day of the week.

If YES was selected, the schedule will be copied to the next day. The

schedule copy may be repeated until Sunday is reached. The Sunday sched-

ule cannot be copied to Monday.

12. After all the times and set points for each day have been entered, press

the Program button to ﬁnish entering the schedule.

NOTE: The thermostat will continue to follow the schedule until a new one

is entered.

• If only one occupied schedule is selected, the Occupied 2 and 3 schedules

are skipped.

• If the start time is set later in the day than the stop time, the program will

run from midnight of that day to the stop time and then from the start time

to midnight.

• If the same start and stop times are programmed for an occupancy sched-

ule, the thermostat will be in Occupied mode for 24 hours.

• If one occupied period starts or stops within another occupied period, the

lower numbered schedule has priority. For example, if schedule

Occupied 3 is running for 24 hours and occupied schedule 2 comes on

from 1 to 3 PM, the set points from Occupied 2 are in effect from 1

to 3 PM.

OVERRIDING THE SCHEDULE — The schedule can be overridden during

operation by pressing the UP or DOWN ARROW buttons to change the de-

sired temperature. The thermostat will use the new set point until the next

scheduled time period starts.

Inhaltsverzeichnis

Andere TOTALINE Thermostat Handbücher

TOTALINE

TOTALINE SIGNATURE CPV230 Bedienungsanleitung

TOTALINE

TOTALINE P710U-21PHP Bedienungsanleitung

TOTALINE

TOTALINE Gold P274-1100 Bedienungsanleitung

TOTALINE

TOTALINE P374-1 700 Bedienungsanleitung

TOTALINE

TOTALINE Easy 1H/1C Bedienungsanleitung

TOTALINE

TOTALINE Gold P274-1100 Bedienungsanleitung

TOTALINE

TOTALINE P374-2 700 Bedienungsanleitung

TOTALINE

TOTALINE P374-1800 Bedienungsanleitung

TOTALINE

TOTALINE P474-0220 Bedienungsanleitung

TOTALINE

TOTALINE P374-1 900 Bedienungsanleitung

TOTALINE

TOTALINE P474-0140 Bedienungsanleitung

TOTALINE

TOTALINE P374-2900 Bedienungsanleitung

TOTALINE

TOTALINE TOTALINE Gold P274-0100-C Bedienungsanleitung

TOTALINE

TOTALINE 1 For All Bedienungsanleitung

TOTALINE

TOTALINE P374-2700 Bedienungsanleitung

TOTALINE

TOTALINE TST-EGND06413SCS09 Bedienungsanleitung

TOTALINE

TOTALINE Intellistat Bedienungsanleitung

TOTALINE

TOTALINE P474-0130 Bedienungsanleitung

TOTALINE

TOTALINE P374-2900 Bedienungsanleitung

TOTALINE

TOTALINE P374-2300FM Bedienungsanleitung

TOTALINE

TOTALINE TOTALINE Gold P274-0100-C Bedienungsanleitung

TOTALINE

TOTALINE Deluxe 1H Bedienungsanleitung

TOTALINE

TOTALINE BASIC 1H Bedienungsanleitung

TOTALINE

TOTALINE 1 For All Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung