TP-Link JetStream TL-SG5428 Bedienungsanleitung

Installation Guide

L2 Managed Switch

TL-SG5428/TL-SG5412F

Business Networking Solution

Specifications are subject to change without notice. is a registered trademark of TP-LINK

TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such

as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the

user may be required to take adequate measures.

Related Document

The User Guide and CLI Reference Guide of the product are provided on the resource

CD.

To obtain the latest product information, please visit the Official Website:

http://www.tp-link.com

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation methods and

the points that should be attended to during installation.

This Installation Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the External Components of the

Switch.

Chapter 2 Installation. This chapter illustrates how to install the Switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning

damage.

Chapter 4 Connection. This chapter illustrates how to do the physical connection of

the Switch.

Chapter 5 Configuration. This chapter instructs you to configure the Switch via Web

Interface and CLI commands.

Appendix A Troubleshooting.

Appendix B Hardware Specifications.

III

Audience

This Installation Guide is for:

Network Engineer

Network Administrator

Conventions

Due to the similarity in the structure of the L2 Managed Switch series, in this

Installation Guide we take TL-SG5428 as an example to illustrate Chapter 2 Installation,

Chapter 3 Lightning Protection and Chapter 4 Connection.

This guide uses the specific formats to highlight special messages. The following table

lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may

result in device damage.

Remind to take notice. The note contains the helpful

information for a better use of the product.

Audience

Contents

Chapter 1 Introduction ———————————— 01

1.1 Product Overview.........................................01

1.2 Appearance .................................................01

Chapter 2 Installation ————————————— 04

2.1 Package Contents.........................................04

2.2 Safety Precautions........................................04

2.3 Installation Tools ..........................................06

2.4 Product Installation ......................................06

Chapter 3 Lightning Protection ———————— 08

3.1 Cabling Reasonably ......................................08

3.2 Connect to Ground .......................................10

3.3 Equipotential Bonding...................................11

3.4 Use Lightning Arrester ..................................12

Chapter 4 Connection ————————————— 13

4.1 Ethernet Port ...............................................13

4.2 SFP Port ......................................................13

4.3 Console Port ................................................15

4.4 Verify Installation .........................................15

4.5 Power On ..................................................15

4.6 Initialization.................................................16

Chapter 5 Conguration———————————— 17

5.1 Congure the switch via GUI.........................17

5.2 Congure the switch Using CLI......................18

Appendix A Troubleshooting—————————— 20

Appendix B Hardware Specications —————— 21

L2 Managed Switch

Chapter 1 Introduction

1.1 Product Overview

TL-SG5428 and TL-SG5412F are Gigabit Ethernet switching products recently developed

by TP-LINK. TL-SG5428 possesses 24 RJ45 ports and 4 SFP slots, while TL-SG5412F

characterizes with 12 SFP slots and 4 RJ45 ports. The SFP slot enables remote

connection with SFP slots on other devices through SFP module and fiber. TL-SG5412F

is compatible with all kinds of gigabit SFP modules. Here you are recommended to

choose gigabit SFP module produced by TP-LINK, which can perfectly extend your

network and enlarge the bandwidth. TL-SG5412F is your first choice to extend the

originally large and medium-sized network.

Designed for workgroups and departments, TL-SG5428/TL-SG5412F from TP-LINK

provides wire-speed performance and full set of layer 2 management features. It

provides a variety of service features and multiple powerful functions with high security.

The EIA-standardized framework and smart configuration capacity can provide flexible

solutions for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection

provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and

video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing

the transport of business critical data. Web, CLI (Console Port, Telnet, SSH), SNMP and

RMON bring abundant management policies. TP-LINK JetStream L2 Managed Switch

integrates multiple functions with excellent performance, and is friendly to manage,

which can fully meet the need of the users demanding higher networking performance.

1.2 Appearance

■Front Panel

The front panel of TL-SG5428 is shown as the following figure.

TL-SG5428

LEDs

Console Port

10/100/1000Mbps RJ45 Port

SFP Port

Figure 1-1 Front Panel of TL-SG5428

The front panel of TL-SG5412F is shown as the following figure.

LEDs

Console Port

SFP Port

10/100/1000Mbps RJ45 Port

Figure 1-2 Front Panel of TL-SG5412F

Introduction

L2 Managed Switch

LEDs ( for TL-SG5428 )

LED Status Indication

PWR

On The switch is powered on

Off The switch is powered off or power supply is abnormal

Flashing Power supply is abnormal

SYS Flashing The switch works properly

On/Off The switch works improperly

1000Mbps On A device is linked to the corresponding port and running at 1000Mbps

Off A 10/100Mbps device or no device is linked to the corresponding port

Link/Act

On A device is linked to the corresponding port and running properly

Flashing Data is being transmitted or received

Off No device is linked to the corresponding port

LEDs ( for TL-SG5412F )

LED Status Indication

PWR On The switch is powered on

Off/Flashing The switch is powered off or power supply is abnormal

SYS Flashing The switch works properly

On/Off The switch works improperly

10/100/1000

BASE-T

Green

On A 1000Mbps device is linked to the corresponding port

and there is no activity

Flashing A 1000Mbps device is linked to the corresponding port

and data is being transmitted or received

Yellow

On A 10/100Mbps device is linked to the corresponding port

and there is no activity

Flashing A 10/100Mbps device is linked to the corresponding port

and data is being transmitted or received

Off No device is linked to the corresponding port

1000Mbps

A 1000Mbps device is linked to the corresponding port

Off No device or a 10/100Mbps device is linked to the

corresponding port

Link/Act

On A 1000Mbps device is linked to the corresponding port

but there is no activity

Flashing A 1000Mbps device is linked to the corresponding port

and data is being transmitted or received

Off No device or a 10/100Mbps device is linked to the

corresponding port

Note:

■The SFP port can work at 1000Mbps mode only, and the Link/Act LED of SFP port will

lighten only when a 1000Mbps device is connected to the corresponding port.

■For TL-SG5428, the SFP ports are individual, while for TL-SG5412F, the four RJ45 ports

combind with four SFP ports are combo ports, which means that the SFP port with

the corresponding RJ45 port cannot work simultaneously. For detailed information

about combo port, please refer to 4.2 SFP Port.

Introduction

L2 Managed Switch

Port Feature

Model 10/100/1000Mbps RJ45 Port SFP Port Console Port

TL-S G5 428 24 4 1

TL-S G5 412F 412 1

10/100/1000Mbps RJ45 Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. For TL-SG5428, each 10/100/1000Mbps RJ45 port has a corresponding

1000Mbps LED and Link/Act LED. But for TL-SG5412F, each 10/100/1000Mbps RJ45

port has a corresponding 10/100/1000BASE-T LED.

SFP Port

Designed to install the SFP module. The SFP ports of these two devices support

1000Mbps SFP module connection only. Each has a corresponding 1000Mbps LED

and Link/Act LED.

Console Port

Designed to connect with the serial port of a computer or terminal for monitoring

and configuring the Switch.

■Rear Panel

Due to the similarity of TL-SG5428 and TL-SG5412F in the rear panel, here TL-SG5428 is

used as an example.

Grounding Terminal

Power Socket

Figure 1-3 Rear Panel of TL-SG5428

Grounding Terminal

The Switch already comes with lightning protection mechanism. You can also ground

the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

For detailed information, please refer to Chapter 3 Lightning Protection.

Power Socket

Connect the female connector of the power cord here, and the male connector to

the AC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage (100-240V~ 50/60Hz).

Caution: Please use the provided power cord.

Introduction

L2 Managed Switch

Chapter 2 Installation

2.1 Package Contents

Make sure that the package contains the following items. If any of the listed items is

damaged or missing, please contact your distributor.

2.2 Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe

the following rules.

■Safety Precautions

■Keep the power off during the installation.

■Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good

skin contact and is well grounded.

■Use only the power cord provided with the switch.

■Make sure that the supply voltage matches the specifications indicated on the rear

panel of the switch.

■Ensure the vent hole is well ventilated and unblocked.

■Do not open or remove the cover of the switch.

■Before cleaning the device, cut off the power supply. Do not clean it by the waterish

cloth, and never use any other liquid cleaning method.

■Site Requirements

To ensure normal operation and long service life of the device, please install it in an

environment that meets the requirements described in the following subsection.

Temperature/Humidity

ȭ

ȭ

TL-SG5428

Installation

One Resource CD

One Switch One Power Cord and One

Console Cable

This Installation Guide

Two mounting brackets and

the ttings

TL-SG5428

L2 Managed Switch

Please keep a proper temperature and humidity in the equipment room. Too high/low

humidity may lead to bad insulation, electricity leakage, mechanical property changes

and corrosions. Too high temperature may accelerate aging of the insulation materials

and can thus significantly shorten the service life of the device. For normal temperature

and humidity of the device, please check the following table.

Environment Temperature Humidity

Operating 0℃~ 40℃10% ~ 90%RH Non-condensing

Storage -40℃~ 70℃5% ~ 90%RH Non-condensing

Clearness

TL-SG5428

The dust accumulated on the Switch can be absorbed by static electricity and result

in poor contact of metal contact points. Some measures have been taken for the

device to prevent static electricity, but too strong static electricity can cause deadly

damage to the electronic elements on the internal circuit board. To avoid the effect of

static electricity on the operation of the Switch, please attach much importance to the

following items:

■Dust the device regularly, and keep the indoor air clean.

■Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference

TL-SG5428

Electronic elements including capacitance and inductance on the device can be affected

by external interferences, such as conducted emission by capacitance coupling,

inductance coupling, and impedance coupling. To decrease the interferences, please

make sure to take the following measures:

■Use the power supply that can effectively filter interference from the power grid.

■Keep the device far from high-frequency, strong-current devices, such as radio

transmitting station.

■Use electromagnetic shielding when necessary.

Lightening Protection

TL-SG5428

Extremely high voltage currents can be produced instantly when lightning occurs and

the air in the electric discharge path can be instantly heated up to 20,000℃. As this

instant current is strong enough to damage electronic devices, more effective lightning

Installation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Schalten Handbücher

TP-Link

TP-Link TL-SL2428 Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL5428E Bedienungsanleitung

TP-Link

TP-Link JetStream T1500G-10MPS Bedienungsanleitung

TP-Link

TP-Link TL-SG105 Bedienungsanleitung

TP-Link

TP-Link TL-SL1218P Bedienungsanleitung

TP-Link

TP-Link TL-SG1008PE Bedienungsanleitung

TP-Link

TP-Link JetStream T3700G-52TQ Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL3428 Bedienungsanleitung

TP-Link

TP-Link T3700G-28TQ Bedienungsanleitung

TP-Link

TP-Link Tapo S200D Bedienungsanleitung

TP-Link

TP-Link T2500G-10TS Bedienungsanleitung

TP-Link

TP-Link T1600G-18TS Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SG3424 Bedienungsanleitung

TP-Link

TP-Link UH400 Bedienungsanleitung

TP-Link

TP-Link T3700G-28TQ Bedienungsanleitung

TP-Link

TP-Link TL-SG2452 Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SG3452X Bedienungsanleitung

TP-Link

TP-Link TL-SG108-M2 Bedienungsanleitung

TP-Link

TP-Link TL-SG2200 Bedienungsanleitung

TP-Link

TP-Link TL-SG1008P Bedienungsanleitung

TP-Link

TP-Link TL-SG1008 Bedienungsanleitung

TP-Link

TP-Link JetStream T1500G-8T Installationsanleitung

TP-Link

TP-Link TL-SG2216 Bedienungsanleitung

TP-Link

TP-Link TL-SL1226 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung