TP-Link Auranet EAP110 Bedienungsanleitung

Typical Network Topology

Hardware Installation

Option 1: Ceiling Mounting

Feed the Ethernet cable through the hole

and set the ceiling tile back into place.

Connect the Ethernet cable to the

ETHERNET port.

Place the mounting bracket in the center

of the ceiling tile. Mark three positions for

the screw holes and a position for the

Ethernet cable hole.

Drill three 4mm holes for the screws and a

25mm hole for the Ethernet cable at the

marked positions.

Remove the ceiling tile.

Secure the mounting bracket to the

ceiling tile using three M3x30 pan-head

screws, washers and wing nuts, as shown

on the left.

EAPEAPEAP

Management Host

A DHCP server (typically a router) is required to assign IP addresses to the EAPs and clients in your local network.

The management host can be in the same or different network segment with the EAPs.

Option 1: Ceiling Mounting

Option 2: Wall Mounting

The EAP can be ceiling-mounted or wall-mounted.

Hole for Ethernet cable

Switch

Router

Internet

Quick Installation Guide

EAP110

Wireless N Access Point

LED Indication

Interface Panel

RESET

With the device powered on, press and hold the button for about 8 seconds until the LED

flashes red, then release the button. The device will restore to factory default settings.

The device is working properly.

Solid green

System errors. RAM, Flash,

Ethernet, WLAN or firmware may

be malfunctioning.

Flashing red

The device is being reset to its

factory default settings.

Double-flashing red, green, yellow

Firmware update is in progress. Do not

disconnect or power o the device.

Flashing yellow

RESET ETHERNET

The port is to connect to the POE port of the provided PoE adapter for both data

transmission and power supply through Ethernet cabling.

ETHERNET

Clients

Wing Nuts (Qty.3)Washers(Qty.3) M3×30 Pan-head Screws (Qty.3)

Attach the EAP to the mounting bracket by

aligning the arrow mark on the EAP with

the arrow mark on the mounting bracket,

then rotate the EAP until it locks into place,

as shown on the left.

EAP Controller

Option 2: Wall Mounting

M3×20 Self-tapping Screws (Qty.3)

M3×28 Plastic Wall Anchors(Qty.3)

Connect the Ethernet cable to the

ETHERNET port on the EAP.

Make two small pencil marks on the

wall. Make sure the two marks are level

and 98.6mm apart.

Drill a 6mm hole through the center of

each mark.

Note: Install the EAP with the Ethernet port downward.

Insert the plastic wall anchors into the

6mm holes and drive the self-tapping

screws into the anchors. Do not drive

the screws all the way in and leave

enough clearance to hang the EAP.

Hang the EAP on the screws. Make sure

the EAP is firmly seated against the

wall.

98.6mm

Attach the EAP to the mounting bracket

by aligning the arrow mark on the EAP

with the arrow mark on the mounting

bracket, then rotate the EAP until it

locks into place, as shown on the left.

Software Configuration

The EAP can be powered via the provided PoE adapter.

Power Supply

To quickly set up a wireless network connection with mass EAPs, please follow the steps

below.

Note: The IP address of the management host must be reachable for the EAPs in the network. In this example, the

management host is in the same LAN as the EAPs.

For More Congurations

You can now manage your wireless network and view network statistics using the EAP

Controller. Please refer to the EAP Controller User Guide for more information about

conguring and using the Controller software.

Step 1: Installing the EAP Controller

On the management host, download the EAP Controller installation file from the product

support page at www.tp-link.com. Run the file and follow the wizard to install the EAP

Controller.

Step 2: Configuring the EAP Controller

Launch the EAP Controller and follow the configuration wizard to create a primary wireless

network. After the wizard is finished, a login screen will appear. Enter the admin name and

password you created and click Sign In.

Step 3: Adopting the EAP devices

Adopt the EAP devices in the Controller management interface to change their status from

Pending to Connected.

(Up to 100m)

PoE LAN

PoE Adapter

Connect the ETHERNET port to the POE port of the PoE adapter using an Ethernet cable. The

cable length can be up to 100 meters.

Connect the Ethernet cable from the switch to the LAN port of the PoE adapter.

Plug the female connector of the provided power cord into the power adapter, and the male

connector to a power outlet.

Passive PoE Adapter

Power LED

The Power LED indicates the status of the electric current: green (0-0.8A), red (0.8A-1A).

PoE Port

This port is used to connect to the ETHERNET port of EAP110.

LAN Port

This Port is used to connect to your LAN.

Power LED PoE Port LAN Port

Switch

For technical support and other information, please visit

http://www.tp-link.com/support, or simply scan the QR code.

The products of TP-Link partly contain software code developed by third parties, including software

code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and any

information on obtaining access to the respective GPL Code used in TP-Link products are available to

you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective programs are

distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For

details, see the GPL Code and other terms of the GPL.

Andere Handbücher für Auranet EAP110

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link TL-WA5210G Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

TP-Link

TP-Link WR702N Bedienungsanleitung

TP-Link

TP-Link TL-WA701ND Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link Auranet EAP320 Bedienungsanleitung

TP-Link

TP-Link TL-WA5210G Bedienungsanleitung

TP-Link

TP-Link Deco E4/W2400 Bedienungsanleitung

TP-Link

TP-Link deco AC1300 Einrichtungshandbuch

TP-Link

TP-Link CPE605 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Omada TPL-EAP225 Bedienungsanleitung

TP-Link

TP-Link Omada EAP653 Bedienungsanleitung

TP-Link

TP-Link Deco X50-PoE Bedienungsanleitung

TP-Link

TP-Link EAP690E Bedienungsanleitung

TP-Link

TP-Link TL-WA7510N Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link PW-AN401 Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

TP-Link

TP-Link Pharos CPE210 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP115-Wall Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link Auranet EAP330 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung