TP-Link Auranet EAP115-Wall Bedienungsanleitung

Network Topology

Hardware Overview 1

Installation Steps

Quick Installation Guide

EAP115-Wall

300Mbps Wireless N Wall-Plate Access Point

Front Panel

Rear Panel

LAN Port

EAPEAPEAP

PoE Switch

Router

Internet

Clients

EAP Controller

RESET

LED

Pre-Installation Checklist

UPLINK+PoE Port

Connected to a PSE (Power Sourcing Equipment), such as a PoE switch, for

both data transmission and Power.

LED/Wi-Fi Button

When the EAP is working in Standalone Mode and enabled with Wi-Fi

Control, press the button to turn on/o both of the Wi-Fi and LED. In other

cases, press the button to turn on/o the LED only.

LAN Port

A wired device can be connected to the LAN port via an Ethernet cable

and access the network.

RESET

With the EAP powered on, press and hold the button for about 5 seconds

until the LED ashes. The EAP will restore to factory default settings.

LED Indicator

On: Working normally/Initializing.

O: Working abnormally/Power o/LED is turned o.

Flashing:

Initialization: The LED ashes twice after initialization is complete.

Upgrade: The LED ashes once per second while upgrading.

Reset: The LED ashes ve times in quick session during the reset. The

EAP will then reboot.

The EAP115-Wall can only be powered by a PSE device, such as a PoE switch.

Connect the PoE switch to the UPLINK+PoE port with an Ethernet cable.

A DHCP server (typically a router) with DHCP function enabled is required to

assign IP addresses to the EAPs and clients in your local network.

Before installation, be sure that you have the following items:

1. A pre-installed wall junction box

2. An RJ45 plug

3. A triangular screwdriver

EAP115-Wall can be mounted into either an 86mm wall junction box or a

standard EU wall junction box. The junction box should be pre-installed with

a running-in-wall Ethernet cable connected to a PoE switch.

LED/Wi-Fi Button

Standard EU wall junction box

86mm wall junction box

4. A Phillips screwdriver

5. A PoE switch

1. Detach the faceplate of the junction box with a Phillips screwdriver

(demonstrated with an 86mm wall junction box).

Software Conguration

2. Detach the faceplate of the EAP with a screwdriver.

3. Connect the Ethernet cable inside the junction box to an RJ45 plug.

Then connect the cable to the UPLINK+PoE port. Position the Ethernet

cable to ensure it is not strained.

5. Press the faceplate of the EAP back into position.

Note:

If the junction box does not have enough room to accommodate the EAP without

straining the Ethernet cable, replace the junction box with an open‑end or deeper one.

The EAP supports two conguring options:

To congure and manage mass EAPs via centralized controller software,

please refer to Option 1.

To congure a single EAP via a web browser directly, please refer to Option 2.

Option 1: Via EAP Controller

Step 1: Installing EAP Controller

On the PC, download the EAP Controller installation le from

http://www.tp-link.com/en/download/EAP-Controller.html. Run the le and

follow the wizard to install the EAP Controller.

Step 2: Conguring EAP Controller

Launch the EAP Controller and follow the step-by-step instructions to

complete the Quick Setup. After the wizard is nished, a login screen will

appear.

Step 3: Logging in to EAP Controller

Enter the admin name and password you created and click Sign In. Then

you can further congure the EAP Controller.

For detailed congurations, please visit http://www.tp-link.com/support to

download the User Guide of EAP Controller in the download center.

Option 2: Via Web Browser

Step 1: Connecting to the EAP Device

Power on the EAP and connect wirelessly by using the default SSID

(format: TP-LINK_2.4GHz_XXXXXX) printed on the product label.

Step 2: Logging in to the EAP Device

Launch a web browser and enter http://tplinkeap.net in the address bar.

Use admin for both Username and Password to log in.

Step 3: Conguring the EAP Device

Set up a new Username and Password for secure management purpose.

Modify the wireless parameters and reconnect your wireless devices to

the new wireless network.

For detailed congurations, please visit http://www.tp-link.com/support to

download the User Guide of EAP in the download center.

For technical support and other information, please visit

http://www.tp-link.com/support, or simply scan the QR code.

The products of TP-Link partly contain software code developed by third parties, including software

code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and

any information on obtaining access to the respective GPL Code used in TP-Link products are

available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective

programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or

more authors. For details, see the GPL Code and other terms of the GPL.

4. Insert the enclosed screws and tighten them with a triangular screwdriver to

secure the mounting bracket.

Note:

Do not over tighten the screws.

If the enclosed screws do not t the junction box, use the screws attached to the

junction box instead.

Andere Handbücher für Auranet EAP115-Wall

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link Omada EAP773 Bedienungsanleitung

TP-Link

TP-Link AP300 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP115 Bedienungsanleitung

TP-Link

TP-Link 6935364097752 Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

TP-Link

TP-Link Omada EAP230-Wall Bedienungsanleitung

TP-Link

TP-Link TL-WA801ND Bedienungsanleitung

TP-Link

TP-Link Auranet Series Bedienungsanleitung

TP-Link

TP-Link Auranet EAP115 Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link M7350 Bedienungsanleitung

TP-Link

TP-Link TL-WA3001 Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP225 Bedienungsanleitung

TP-Link

TP-Link TL-WA7210N Betriebsanleitung

TP-Link

TP-Link deco AC1300 Einrichtungshandbuch

TP-Link

TP-Link AP9635 Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA801ND Bedienungsanleitung

TP-Link

TP-Link Pharos CPE210 Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link Omada Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung