TP-Link Auranet EAP120 Bedienungsanleitung

Installation Guide

Wireless N Gigabit Access Point

EAP120 / EAP220

CONTENTS

About This Installation Guide

This guide is designed to familiarize you with the general layout of the EAP,

describe how to perform the hardware installation for EAP Series, and how to

configure the EAP in your network. Your EAP has more features and functionalities

which can be found in the User Guide.

Conventions

The EAP or the device mentioned in this guide stands for Wireless N Gigabit Access

Point EAP120 and EAP220.

EAP Topology ——————————————————————— 01

Overview ————————————————————————— 02

Hardware Installation ——————————————————— 04

1. Installation Requirements ....................................................... 04

2. Mounting Bracket ................................................................... 04

3. Installation ............................................................................ 05

4. Powering Mode ...................................................................... 09

Getting Started with EAP—————————————————— 11

Q&A ——————————————————————————— 14

Specications ——————————————————————— 15

Technical Support ————————————————————— 16

EAP Topology

A typical network topology for the EAP is shown below.

Router

Internet

Switch

Master EAP Member EAPMember EAP

Enwuvgt

The EAP120 and EAP220 provide two management modes: Cluster and Standalone.

By default, the management mode is Cluster. In this mode, all EAPs in the same

LAN (Local Area Network) form a cluster, and a Master EAP will be selected to

manage other Member EAPs.

To deploy an EAP in your local network, a DHCP server is required to assign IP

address to the EAP. Typically, a router acts as the DHCP server.

The EAP can be powered directly by a Power over Ethernet (PoE) switch through

the Ethernet port, or the provided power adapter.

Hardware Overview

■LED

System LED

LED Status Indication

Flashing green System initialization is complete.

Solid green The device is working properly.

Flashing red System errors. RAM, Flash, Ethernet, WLAN or

firmware may be malfunctioning.

Flashing yellow Firmware update is in progress. Do not disconnect

or power off the device.

Alternating red/green/yellow twice The device is being reset to its factory default

settings.

■Interface Panel

RESET CONSOLE ETHERNET ON/OFF POWER

ARROW 1

The interface panel components of the EAP, from left to right, are described in the

following list:

Kensington Security Slot

Secure the lock (not provided) into the security slot to prevent the device from

being stolen.

RESET

With the device powered on, press and hold the RESET button for about 8 seconds

until the LED ashes red/green/yellow alternatively twice, then release the button.

The device will restore to factory default settings.

CONSOLE

This port is used to connect to the serial port of a computer or a terminal to check

and monitor system information of the device.

Note: CLI commands are not available in current software version. We will release

a new version supporting CLI commands soon. Please pay close attention to our

ofcial website.

ETHERNET

This port is used to connect to a router to transmit data or to a PSE (Power

Sourcing Equipment), such as a PoE switch, for both data transmission and Power

over Ethernet (PoE) through Ethernet cable.

ON/OFF

Press this button to turn on/off the device.

POWER

The power port is used to connect the device to an electrical wall outlet via power

adapter. Please only use the provided power adapter. Refer to Powering Mode to

learn how to power the device via PoE or power adapter.

ARROW 1

This arrow is used to align with ARROW 2 on the mounting bracket to lock the EAP

into place. Please refer to Mounting Bracket to locate ARROW 2.

Hardware Installation

The EAP can be wall or ceiling-mounted and can be powered via a PSE device

or the provided power adapter. Please suitably arrange your wire layout before

mounting the EAP.

1. Installation Requirements

Before installation, check the package contents for the following items:

Other installation equipments may require, including a pencil, ruler, drill, drill bit,

hammer, screwdriver and a ladder.

2. Mounting Bracket

The following figure describes the structure of the mounting bracket.

Locking clip

ARROW 2 is used to align

with ARROW 1 under the

interface panel

Ceiling mounting slot

Wall mounting slot

Mounting Bracket

EAP120/EAP220 Mounting Bracket Installation Guide

Wing Nuts (3) Washers (3) Plastic Wall

Anchors (3)

Self-tapping

Screws (3)

Pan-head

Screws (3)

3. Installation

■Ceiling Mounting

Note:

■Make sure the thickness of the ceiling is less than 18mm and

the ceiling can bear at least five kilograms.

■It is NOT recommended to mount the EAP on a low-strength

material, such as gypsum ceiling panel. If no other choice is

available, make sure you add a piece of strong material under

the wing nuts to ensure the EAP is mounted solidly.

1. Remove the ceiling tile.

2. Place the mounting bracket in the center of the ceiling tile. Mark the positions

of the three mounting slots and a hole for the Ethernet cable to feed through.

L≈40mm

Mark of the Hole for Ethernet

cable to feed through

3. Use a drill with the appropriate size drill bit to drill three 4mm holes for

the pan-head screws, and drill a 10mm hole for the Ethernet cable to feed

through.

10mm hole for Ethernet cable feed

4mm hole for mounting bracket

4. Secure the mounting bracket to the ceiling tile using the pan-head screws (3),

washers (3) and wing nuts (3), as shown below.

Hole to feed the Ethernet cable

Hole to feed the screw

Pan head screw

Wing nut

Washer

5. Attach the EAP to the mounting bracket by aligning ARROW 1 with ARROW 2,

as shown below.

RESET CONSOLE ETHERNET ON/OFF POWER

ARROW 2

ARROW 1

6. Turn the EAP clockwise until it locks into place.

Andere Handbücher für Auranet EAP120

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link TL-WA901N Bedienungsanleitung

TP-Link

TP-Link Omada Pro AP7650 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP330 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Omada EAP230-Wall Bedienungsanleitung

TP-Link

TP-Link Auranet EAP320 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link TL-WA5210G Bedienungsanleitung

TP-Link

TP-Link AP8635-I Bedienungsanleitung

TP-Link

TP-Link TL-WA5110G Bedienungsanleitung

TP-Link

TP-Link TL-WA901N Bedienungsanleitung

TP-Link

TP-Link Auranet EAP225 Bedienungsanleitung

TP-Link

TP-Link Omada EAP110 Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP115 Bedienungsanleitung

TP-Link

TP-Link 54Mbps Wireless Access Point TL-WA501G Bedienungsanleitung

TP-Link

TP-Link TL-WA701ND Bedienungsanleitung

TP-Link

TP-Link AURANET CAP300-Outdoor Bedienungsanleitung

TP-Link

TP-Link AP200 Bedienungsanleitung

TP-Link

TP-Link Omada Pro Bedienungsanleitung

TP-Link

TP-Link Omada EAP225-Wall Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link Pharos CPE210 Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung