TP-Link Omada EAP225-Wall Bedienungsanleitung

Network Topology

Hardware Overview 1

Installation Steps

Quick Installation Guide

EAP225-Wall

AC1200 Wireless MU-MIMO Wall Plate Access Point

Front Panel & Rear Panel

Bottom View Pre-Installation Checklist

RESET Button

With the device powered on, press and hold the button for 5 seconds to reset

the EAP to its factory defaults.

ETH1 & ETH2 Port

Connected to a client device to transmit data.

ETH3 (PoE OUT) Port

Connected to a client device to transmit data and supply power (PoE

Passthrough). The PoE OUT feature requires 802.3at PoE+ input and the

maximum output is 13W.

LED Indicator

On: Working normally/Initializing.

O: Working abnormally/Power o/LED is turned o.

Flashing:

Initialization: The LED ashes twice after initialization is complete.

Upgrade: The LED ashes once per second while upgrading.

Reset: The LED ashes ve times in quick session during the reset. The

EAP will then reboot.

ETH0 (PoE IN) Port

Connected to a PSE (Power Sourcing Equipment), such as a PoE switch,

for both data transmission and Power. The device supports 802.3at

inputs.

LED Button

Press the LED button to turn on/o the LED. The EAP225-Wall can only be powered by a PSE device, such as a PoE switch.

Connect the PoE switch to the ETH0 (PoE IN) port with an Ethernet cable.

A DHCP server (typically a router) with DHCP function enabled is required to

assign IP addresses to the EAPs and clients in your local network.

Before installation, be sure that you have the following items:

1. A pre-installed wall junction box

2. An RJ45 plug

EAP225-Wall can be mounted into an 86mm wall junction box, a standard

EU wall junction box, or a standard US junction box. The junction box should

be pre-installed with a running-in-wall Ethernet cable connected to a PoE

switch.

Standard EU wall junction box86mm wall junction box

EAPEAPEAPPC

PoE Switch

Router

Internet

Clients

EAP Controller

3. A Phillips screwdriver

4. A PoE switch

Standard US wall junction box

ETH1 ETH2

RESET

ETH3 (PoE OUT)

Note:

For simplicity, the 86mm wall junction box is used as an example below.

For security reasons, it is recommended not to install the EAP with the louver

downward.

Note: To power and connect an 802.3af device to the LAN, you must use

802.3 at PoE+ input.

1. Detach the faceplate of the junction box with a Phillips screwdriver.

LED

ETH0 (PoE IN)

LED Button

Software Conguration

2. Slide the mounting bracket to detach it from the EAP.

3. Insert the enclosed screws and tighten them with a philips screwdriver

to secure the mounting bracket.

5. Attach the EAP to the mounting bracket by aligning the two mounting studs

on the mounting bracket with the large openning of the slots on the EAP.

Press and slide the EAP down until it locks into place.

The EAP supports two conguring options:

To congure and manage mass EAPs via centralized controller software,

please refer to Option 1.

To congure a single EAP via a web browser directly, please refer to

Option 2.

Option 1: Via EAP Controller

Step 1: Installing EAP Controller

On the PC, download the EAP Controller installation le from

http://www.tp-link.com/en/download/EAP-Controller.html. Run the le and

follow the wizard to install the EAP Controller.

Step 2: Conguring EAP Controller

Launch the EAP Controller and follow the step-by-step instructions to

complete the Quick Setup. After the wizard is nished, a login screen will

appear.

Step 3: Logging in to EAP Controller

Enter the admin name and password you created and click Sign In. Then

you can further congure the EAP Controller.

For detailed congurations, please visit http://www.tp-link.com/support to

download the User Guide of EAP Controller in the download center.

Option 2: Via Web Browser

Step 1: Connecting to the EAP Device

Power on the EAP and connect wirelessly by using the default SSID

(format: TP-Link_2.4GHz/5GHz_XXXXXX) printed on the product label.

Step 2: Logging in to the EAP Device

Launch a web browser and enter http://tplinkeap.net in the address bar.

Use admin for both Username and Password to log in.

Step 3: Conguring the EAP Device

Set up a new Username and Password for secure management purpose.

Modify the wireless parameters and reconnect your wireless devices to

the new wireless network.

For detailed congurations, please visit http://www.tp-link.com/support to

download the User Guide of EAP in the download center.

For technical support, User Guide and other information, please

visit http://www.tp-link.com/support, or simply scan the QR code.

The products of TP-Link partly contain software code developed by third parties, including software

code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and

any information on obtaining access to the respective GPL Code used in TP-Link products are

available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective

programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or

more authors. For details, see the GPL Code and other terms of the GPL.

Note:

Do not over tighten the screws.

If the enclosed screws do not t the junction box, use the screws attached to the

junction box instead.

When mounting the bracket to a standard US junction box, use the holes on the

top and bottom side.

4. Connect the Ethernet cable inside the junction box to an RJ45 plug. Then

connect the cable to the ETH0 (PoE IN) port. Position the Ethernet cable to

ensure it is not strained.

Note:

If the junction box does not have enough room to accommodate the EAP, replace an

open‑end junction box or a deeper one.

Tip:

To remove the EAP from the mounting bracket, insert a metal stick into the hole

next to the LED button to release the Locking Tab. Slide the EAP upwards and

pull it out to detach it from the mounting bracket, as shown below.

Andere Handbücher für Omada EAP225-Wall

Inhaltsverzeichnis

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link Auranet EAP120 Bedienungsanleitung

TP-Link

TP-Link TL-WA801ND Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP120 Bedienungsanleitung

TP-Link

TP-Link TL-WA901N Bedienungsanleitung

TP-Link

TP-Link AURANET CAP300-Outdoor Bedienungsanleitung

TP-Link

TP-Link Auranet EAP330 Bedienungsanleitung

TP-Link

TP-Link Omada Pro AP7650 Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link omada OC200 Bedienungsanleitung

TP-Link

TP-Link AP200 Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA7210N Bedienungsanleitung

TP-Link

TP-Link AP200 Bedienungsanleitung

TP-Link

TP-Link CPE605 Bedienungsanleitung

TP-Link

TP-Link TL-WA801ND Handbuch

TP-Link

TP-Link Omada EAP653 Bedienungsanleitung

TP-Link

TP-Link TL-WA7510N Bedienungsanleitung

TP-Link

TP-Link Omada EAP620 HD V2 Bedienungsanleitung

TP-Link

TP-Link PHAROS SERIES Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link TL-WA3001 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung