TP-Link TL-WA5210G Bedienungsanleitung

Typical network

Note The typical connection for TL-WA5210G is shown as above. Please make

sure that the two CPEs are placed face to face, otherwise the wireless

signal strength might be weak. Here shows several incorrect examples.

TL-WA5210G is used for remote point-to-point connection. It makes remote

internet share possible.

Note If you are using an external antenna to connect, please refer to Appendix 1.

Locate a suitable mounting site for your CPE. For choosing the best location,

select an elevated location where trees, buildings and large steel structures will

not obstruct the antenna signals and which offers maximum line-of-sight

propagation with the users.

Connect one end of an

Ethernet cable to the POE

port of the provided Power

Injector and the other end

of the Ethernet cable to the

LAN port of the CPE. Then,

connect the LAN port of the

Power Injector to a PC

using another Ethernet

cable. Finally, plug the

provided power adapter

into the DC jack on the

Power Injector, and the

other end to a standard

electrical wall socket.

Note Please use only wired network connections to configure the AP.

djust the direction of your CPE for a best signal. Place the straps through the

slots on the back of the CPE and then around the

ole. Ti

hten the stra

Connecting the device

Note To get a best signal, you can refer to the Antenna Alignment on Page 8.

The connection will be similar to the figure below after the above steps are

finished.

Turn on all your network devices and then check to see if the LEDs on the AP

display normally as the diagram below describes.

Note If the LEDs display abnormally, please check to see if all the cable connectors

(power adapter and Ethernet cable) are well connected to your device.

If you use two

CPEs to build

the network,

please make

sure that the

two CPEs are

placed face to

face.

Solid light

Solid light or flashing

dialog box will prompt you for the

User name and Password.Ente

the default values and click OK.

Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting

guide. T2 will give you some help if you forget the password.

The web management page will

display after successfully logging in.

Note You will need to assign your computer a Static IP address within the same

range as the AP’s IP address. See the Troubleshooting T3 if you need

assistance.

User name: admin

Password: admin

Click OK

Configuring the device

Click Quick Setup

Open your web browser and type

http://192.168.1.254 in the address

bar and press Enter

Operation Mode Setting

A. Configuration for AP Client Router Mode

This page will then display.

The AP supports three operation mode types: AP Client Router,

P Route

and AP.

a) If you want to connect to your WISP, please choose

P Client Route

mode and proceed to AǗ

b) If you want to set it as a router, please choose AP Router mode, and fo

further configuration, please refer to the user guide in the resource CD;

c) If you want to set up a point-to-point connection with TL-WA5210G,

please skip to B;

If you want to set it as a repeater, please skip to C.

Note

Click Next

The Username and Password are provided by your WISP.

Note

Click Next

Choose the Operation Mode Type

appropriate to your needs

Enter the Username and Password

given by your WISP

Click Next

Choose your WAN Connection

Type provided by your WISP. Here

we choose PPPoE as an example

Click Finish

B. Configuration for Point-to-Point Connection

The AP Setting

Click Finish to exit the Quick Setup

wizard and wait until the AP completes

rebooting automatically. The changes

will take effect after rebooting.

Click Finish

Enter the SSID provided

by your WISP

Click Next

Click Finish to exit the Quick Setup

wizard and wait until the AP completes

rebooting automatically. The changes

will take effect after rebooting.

Click Next

Select AP

Enter a unique name for your wireless

network; however, choose a name that

is easily remembered by network users.

Here we enter TP-LINK_900008 as the

SSID for example

Select your region from the drop-down list

Click Next

Note Two TL-WA5210Gs are needed for this application.

Click Wireless >

Wireless Mode

Select Client

Enter TP-LINK_900008, the SSID

of the first AP you have configured

After successfully logging in, configure the other TL-WA5210G by following the steps

below.

The Client Setting

Click Save at the bottom of this page.

C. Configuration for Repeater

To make sure the TL-WA5210G is under AP mode, please follow the steps below.

The AP will begin rebooting automatically after you click Save.

Note You should change the default LAN IP address of the Client from

192.168.1.254 to 192.168.1.X (X can be any number from 2 to 253) to avoid

an IP conflict with the former AP. Here we choose 192.168.1.2 as an example.

Note

Click Save

Click Network

Enter 192.168.1.2 in the

IP Address field

Click Save

Select AP

Click Operation Mode

Then click Save at the bottom of this page.

Antenna Alignment

fter basic configuration of operation

mode, you can change your CPE’s

direction to get a better signal strength

according to the parameters shown on

the Antenna Alignment page.

Click Wireless

Click Antenna Alignment

This page will then display.

The BSSID is the same as the MAC address.

Note

Select Repeater

Click Survey

Click Wireless >

Wireless Mode

Find the BSSID of the remote AP

that you want to repeat, and then

click Connect on the right side of

the line.

Connect one side of the TL-ANT24SP to the RP-SMA port of your CPE through

the TL-ANT24PT3.

Connect the other side of the TL-ANT24SP to the TL-ANT2424B.

Appendix 1:

External antenna installation

1 External antenna connection

Configure the external antenna

Note 1. If you have an external antenna with the RP-SMA (male) port, you could

connect it to the RP-SMA port of your CPE directly.

2. If you don’t have any external antennas, you are recommended to use

TP-LINK products for outdoor solution. You could choose TL-ANT2424B

(external antenna), TL-ANT24SP (Surge Protector), and TL-ANT24PT3

(Pigtail Cable) to connect as the following steps:

Note You will need to assign your computer a Static IP address within the same

range as the AP’s IP address. See the Troubleshooting T3 if you need

assistance.

Configure the external antenna

’

dialog box will prompt you for the

User name and Password.Ente

the default values and click OK.

User name: admin

Password: admin

Click OK

Open your web browser and type in

http://192.168.1.254 in the address

bar and press Enter

Select External

Click Save

Click Wireless Setting

Andere Handbücher für TL-WA5210G

Inhaltsverzeichnis

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link Auranet EAP120 Kurzanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link 6935364097752 Bedienungsanleitung

TP-Link

TP-Link TL-WA500G Bedienungsanleitung

TP-Link

TP-Link Auranet EAP120 Bedienungsanleitung

TP-Link

TP-Link TL-WA701ND Bedienungsanleitung

TP-Link

TP-Link TL-WA801ND Bedienungsanleitung

TP-Link

TP-Link Omada EAP230-Wall Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link TL-WA801N Bedienungsanleitung

TP-Link

TP-Link Deco E4/W2400 Bedienungsanleitung

TP-Link

TP-Link TL-WA850RE Bedienungsanleitung

TP-Link

TP-Link omada OC200 Bedienungsanleitung

TP-Link

TP-Link TL-WA3001 Bedienungsanleitung

TP-Link

TP-Link CPE605 Bedienungsanleitung

TP-Link

TP-Link AP500 Bedienungsanleitung

TP-Link

TP-Link Omada EAP115-Wall Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link Omada EAP230-Wall Bedienungsanleitung

TP-Link

TP-Link Auranet EAP225 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung