TPI 597 Bedienungsanleitung

597

Digital Hygrometer / Psychrometer

The Value LeaderTM

www.tpi-thevalueleader.com

Contents

1. Introduction

2. General Overview & Guidelines

3. Instrument Overview

4. Keypad Functions

5. Operating Instructions

6. PC Communication

7. Troubleshooting

8. Battery Replacement

9. Care & Cleaning

10. Specifications

1. Introduction

Thank you for purchasing TPI brand products. The TPI 597 digital

hygrometer / psychrometer is a state of the art, easy to use humidity

tester designed to display ambient, dew point, and wet bulb tempera-

ture as well as humidity. The instrument is ruggedly constructed and

comes with a 3 Year Guarantee.

2. General Overview & Guidelines

The TPI 597 hygrometer is guaranteed free from defects in materials and

workmanship for 3 Years from the date of purchase. This guarantee does not

affect your statuary rights. For additional information please refer to the

included warranty card or contact TPI at 800-368-5719.. To maintain opti-

mum performance, calibration is recommended once every year.

To obtain warranty performance or calibration of your meter: - Include with

the product your name, address, phone number, written description of the

problem and proof of purchase date. Carefully package and return to:

TPI / Attn. Repair

9615 SW Allen Blvd. Suite 104

Beaverton, OR 97005

General Guidelines:

Always allow the 597 sufficient time to acclimate to the test environ-

ment especially when moving from room to room.

Always store and operate the 597 within the temperature and humidity

limits outlined in the specifications area of this manual.

Never allow any object to enter the sensor area of the wand.

Your TPI 597 comes complete with the following standard accessories:

•TPI 597 Instrument

•Rubber Boot

•Battery (9Volt)

•Instruction manual

3. Instrument Overview

Rubber Boot Protects the instrument from accidental damage

Display Large 2 parameter LCD display

Sensor Cage Houses and protects the sensor

Keypad Selects all available functions

Sensor Wand Handle for manuevering sensor

RS-232 Output Jack Use with optional cable part number A500 to

stream data to a computer

Rubber Boot

Display

Sensor Cage

Sensor Wand

Keypad

RS232 Output

Jack

4. Keypad Functions

Turns the instrument ON and OFF.

Freezes the displayed reading. When hold is active “DH” is dis-

played.

Switches the displayed temperature reading between Celsius and

Fahrenheit.

Toggles the record feature ON and OFF. When record is active

“REC” is displayed.

Toggles the displayed temperature reading between ambient (Ta),

dew point (Td), and wet bulb (Tw).

When record is active, recall (RCL) is used to toggle between

maximum recorded values (MAX), minimum recorded values

(MIN), average recorded values (AVG), and turn on RS232 com-

munication (RS-232).

HOLD

°C

°F

REC

MODE

RCL

5. Operating Instructions

1. Press the key to turn the 597 on.

2. Humidity will be displayed in the upper portion of the display and temper-

ature will be displayed in the bottom portion of the display.

3. Press the key to select the desired unit of measure for tempera-

ture.

4. Hold the sensor wand in the area to be tested.

4. Press the key to cycle through the type of displayed temperature.

Ambient temperature = “Ta” displayed

Dew Point temperature = “Td” displayed

Wet Bulb temperature = “Tw” displayed

5. Press the key to freeze the displayed readings as necessary.

HOLD

MODE

°C

°F

Relative humidity (RH) dis-

played in percent.

Temperature displayed in

Celsius or Fahrenheit.

Ta = Ambient Temperature

Td = Dew Point Temperature

Tw = Wet Bulb Temperature

Using record (REC) and recall (RCL)

1. Press the key to activate record mode.

2. Press the key repeatedly to toggle the display through maximum,

minimum, average readings, and to activate PC communication.

Maximum reading = “MAX” displayed

Minimum reading = “MIN” displayed

Average reading = “AVG” displayed

RS-232 communication active = “RS-232” displayed

3. Press the key to return to normal operation.

6. PC Communication (RS-232)

1. Connect the A500 RS232 cable to the TPI 597 and computer.

2. As outlined above, turn the 597 on and activate communication mode.

3. Open Microsoft Hyper Terminal (or other serial program) and set the COM

port as shown below.

a. Baud Rate: 9600

b. Data Bits: 8

c. Parity: None

d. Stop Bits: 1

e. Flow Control: None

4. The TPI 597 will stream data in ASCII format with an update rate of

approximately 5 seconds.

REC

RCL

REC

7. Troubleshooting

Problem Solution

Unit will not turn on Change the battery

Will not display humidity or Return to TPI for service

temperature.

8. Battery Replacement

1. Remove the unit from the protective boot. The battery cover is at the bot-

tom of the unit and is marked battery.

2. Loosen the battery compartment screw and remove the battery door by

pulling on the screw.

3. Replace the battery.

4. Install the battery compartment door and tighten the screw. Put the protec-

tive boot back on the unit.

9. Care & Cleaning

Clean the 597 with a soft lint free cloth. Do not attempt to clean the sensor.

10. Specifications

Display: Dual display LCD with annunciators

Measurement Range and Accuracy

Humidity:

Range: 0% to 100% (Temp: 32°F to 122°F / 0°C to 50°C)

Accuracy: 30% to 85% = +/-(2% of rdg + 2%RH) ( 59°F to 104°F / 15°C to 40°C)

<30% and >85% = +/-3%RH ( 59°F to 104°F / 15°C to 40°C)

+/-5% RH at temperatures <59°F (15°C) or >104°F (40°C)

Resolution: 0.1% RH

Wet Bulb: Calculated

Dewpoint: Calculated

Temperaure:

Range: -40°F to 212°F

Accuracy: +/-(0.5% of reading + 2.0°F)

Resolution: 0.1°

Range: -40°C to 100°C

Accuracy: +/-(0.5% of reading + 1.0°C)

Resolution: 0.1°

Operating Temperature & Humidity (Base Unit):

32°F to 122°F (0°C to 50°C) at less than 90% RH

Power Source:

9V Alkaline Battery (30 hour typical battery life)

Dimensions:

5.8” x 2.9” x 1.2” (148mm x 73mm x 30mm)

Weight:

0.3lbs (0.14kg)

Notes

Andere Handbücher für 597

Inhaltsverzeichnis

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung