Transcend Sleep Aphea Therapy SYSTEM Bedienungsanleitung

Sleep Apnea Therapy

Software User Manual

Page ii Sleep Apnea Therapy Software User Manual

Notices

Revised Sleep Apnea Therapy Software User Manual 103392 Rev B

Published February 8, 2013 and supersedes all previous versions.

Notice The information contained in this document is subject to change without notice.

Trademark Somnetics®and Transcend®are registered trademarks of Somnetics International, Inc.;

Contact Somnetics International, Inc.

Corporate headquarters Somnetics International, Inc.

Email [email protected]

Web http://www.mytranscend.com/

Telephone 651.621.1800

Toll-free telephone 877.621.9626

Fax 651.204.0064

Somnetics International, Inc.

33 5th Avenue NW, Suite 500

New Brighton, Minnesota 55112 USA

Authorized Representative (MDD 93/42/EEC)

Methodize Europe

Drieblad 11

NL-2811EG Reeuwijk

The Netherlands

Telephone +31 6 2129 4150l

Rx Only

Sleep Apnea Therapy Software User Manual Page iii

About this user guide

Note This user guide is designed to be duplex-printed (printed on both sides of each

sheet). If not printed in this manner, you will find blank pages in your printout.

Note For purposes of this manual, some software screen images may differ from the

actual screen display. This is only for clear printing and on-screen display of this

manual.

Important notes

The information contained in this document is subject to change without notice.

Note Indicates a tip or feature to aid efficient operation of the device.

General Guidelines and Precautions

This section contains information that is essential for safe operation of this product. Read

and understand these instructions before using this product or any optional equipment.

For more warning instructions, refer to additional materials supplied with the device.

Somnetics products are designed and manufactured for use in conjunction with

accessories supplied and recommended by Somnetics. Accessories designed by other

manufacturers have not been tested and should not be used with Somnetics products.

Page iv Sleep Apnea Therapy Software User Manual

Contents

Introduction ..............................................................................................1

Installation ................................................................................................2

System requirements ..........................................................................................2

Installation procedure..........................................................................................3

Using the Sleep Apnea Therapy Software ..................................................6

Common procedures ...........................................................................................8

View compliance data .....................................................................................9

Email compliance data to clinician...................................................................12

Adjusting data in compliance reports ..............................................................13

View/send a device fault log ..........................................................................15

Reset a device fault ......................................................................................16

Exit the program ..........................................................................................16

Introduction

The Somnetics Sleep Apnea Therapy

software is intended for use by both

patients and clinicians.

Patients may use the program to view the

therapy settings programmed into their

device by their clinician, view the therapy

history stored in the device, and send

compliance data to their clinician.

In addition to the above, clinicians may use

the program to view, set, or modify the

device settings; calibrate the device; or

retrieve compliance data from the device.

Page 2 Sleep Apnea Therapy Software User Manual

Installation

This section includes instructions for installing the Sleep Apnea Therapy software.

•System requirements

•Installation procedure

System requirements

The Sleep Apnea Therapy software is installed from a CD-ROM, which contains a setup

program to help guide you through the setup and installation process. Before installing the

software, ensure that the following minimum computer system requirements are met:

•Operating system: Windows XP, Windows 7 (32-bit or 64-bit), or Windows 8 (32-bit

or 64-bit)

•Available USB port

•512MB of RAM (the software can be installed on systems that do not meet this

requirement; however, speed and performance may be compromised)

•Video settings of at least 1024 x 768, and at least 32-bit color (lower settings might

impair readability)

Note You must have administrator privileges in order to install this software, update this

software, or restore the patient database. Administrator privileges are not required

to operate the software.

Note Install the software before connecting the device USB cable to the computer.

Note Some antivirus software may interfere with software installation. If difficulties arise

during installation, consult an IT professional about disabling antivirus software

during installation.

Sleep Apnea Therapy Software User Manual Page 3

Installation procedure

Follow these steps to install the Sleep Apnea Therapy software.

Note: You must have administration privileges to install this software. For questions

regarding administration privileges refer to an IT professional.

1. Log in to the computer on which the

software will be installed. Close all

other open programs before

installation.

Insert the Sleep Apnea Therapy

software CD into your computer disk

drive. If you do not have the software

installation CD the software can be

downloaded from

www.mytranscend.com/resources.

3. The install wizard will verify the setup

package.

Note:If you are updating existing

Transcend software you will be

instructed to uninstall your current

version of software before installing

an updated version.

Select Next> to proceed.

4. Select your language from the menu

and click OK.

5. A dialog box similar to the one shown

will appear notifying the user that the

installation setup is ready to begin.

6. Click Next> to begin the installation.

Note Software and Transcend user manual updates can be download at

http://www.mytranscend.com/resources

Page 4 Sleep Apnea Therapy Software User Manual

7. A destination folder for software

installation will be recommended. To

change the selected destination folder

click Change and enter a new

destination.

Click Next> to continue.

8. The install program will automatically

name the program folder. To change

the name of the folder, simply type a

new file name in the text box.

9. To allow software access to all users,

select Anyone who uses this

computer. To restrict access to you

only select Only for me.

Click Next> to continue.

10. A window will appear confirming the

installation settings. Click <Back to

edit the settings or Cancel to exit.

Click Next> to continue with

installation.

Sleep Apnea Therapy Software User Manual Page 5

11. The Sleep Apnea Therapy Software

will now initiate installation. A

progress bar will appear indicating

installation progress.

12.

Windows must be restarted to apply

the changes to your computer

following successful installation. To

restart Windows automatically click

Finish. To restart at a later time

uncheck the Restart Now box, then

click Finish.

Page 6 Sleep Apnea Therapy Software User Manual

Using the Sleep Apnea Therapy Software

Note You must have the device connected to your computer with the USB cable in order

to view compliance data.

Note You must close all other open programs before launching the Transcend Sleep

Apnea Therapy Software.

1. There are two ways to launch the Sleep Apnea Therapy software:

♦Choose StartProgramsSomneticsSleep Apnea Therapy

SoftwareSleep Apnea Therapy Software.

♦Double-click the Somnetics Sleep Apnea Therapy Software

icon on your computer desktop.

The program opens with a Welcome

screen similar to the one shown here.

From this window you have the option

to select a different language.

Note If the Transcend device is in a fault

state, the program displays a fault

message when you connect the device

to the computer with the USB cable

and launch the Sleep Apnea Therapy

software.

See Reset a device fault for more

information.

Inhaltsverzeichnis

Andere Transcend Medizinische Geräte Handbücher

Transcend

Transcend AUTO Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Transcend

Transcend EZEX Bedienungsanleitung

Transcend

Transcend AUTO Bedienungsanleitung

Transcend

Transcend Micro Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Transcend

Transcend EZEX Bedienungsanleitung

Transcend

Transcend 3 miniCPAP Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Transcend

Transcend Micro Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Transcend

Transcend 3 miniCPAP Bedienungsanleitung

Transcend

Transcend CPAP Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Transcend

Transcend 2 Bedienungsanleitung

Transcend

Transcend Micro Bedienungsanleitung

Transcend

Transcend 365 miniCPAP Auto Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung