Transition Networks SM24TAT2DPA Bedienungsanleitung

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 1of 23

SM24TAT2DPA

Managed Switch, 24-port Gigabit PoE+,

2-port SFP/RJ-45 Combo

Install Guide

33702 Rev. A

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 1of 23

Safety Warnings and Cautions

These products are not intended for use in life support products where failure of a product could reasonably be

expected to result in death or personal injury. Anyone using this product in such an application without express written

consent of an officer of Transition Networks does so at their own risk, and agrees to fully indemnify Transition

Networks for any damages that may result from such use or sale.

Attention: this product, like all electronic products, uses semiconductors that can be damaged by

ESD (electrostatic discharge). Always observe appropriate precautions when handling.

NOTE: Emphasizes important information or calls your attention to related features or

instructions.

WARNING:

Alerts you to a potential hazard that could cause personal injury.

CAUTION:

Alerts you to a potential hazard that could cause loss of data, or damage the system

or equipment.

SM24TAT2DPA Install Guide - TN PN 33702 Rev. A

Record of Revisions

Rev Date Description of Changes

A 11/7/16 Initial release for software v6.48.

Trademark notice

All trademarks and registered trademarks are the property of their respective owners. All other products or

service names used in this publication are for identification purposes only, and may be trademarks or

registered trademarks of their respective companies. All other trademarks or registered trademarks

mentioned herein are the property of their respective holders.

any form or by any means (graphic, electronic, or mechanical) without written permission from Transition

Networks.

Address comments on this product or manual to:

Transition Networks Inc.

10900 Red Circle Drive, Minnetonka, MN 55343

tel: +1.952.941.7600 | toll free: 1.800.526.9267 | fax: 952.941.2322

[email protected] | techsupport@transition.com | [email protected]m

web: https://www.transition.com

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 3of 23

Compliance and Safety Statements

FCC-CLASS A: This equipment has been tested and found to comply with the limits for a Class A

computing device pursuant to Subpart J of part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference when operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better for 10 Mbps

connections, Category 5 or better for 100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps

connections. For fiber optic connections, you may use 50/125 or 62.5/125 micron multimode fiber or

9/125 micron single-mode fiber.

CE MARK DECLARATION OF CONFORMANCE FOR EMI AND SAFETY (EEC): This equipment has

been tested and found to comply with the protection requirements of European Emission Standard

EN55022/EN61000-3 and the Generic European Immunity Standard EN55024.

Declaration of Conformity

Related Manuals

The following manuals give specific information on how to use the switch:



SM24TAT2DPA Quick Start Guide, 33701



SM24TAT2DPA Install Guide, 33702



SM24TAT2DPA Web User Guide, 33703



SM24TAT2DPA CLI Reference, 33704

To access the manuals, firmware, datasheet or other documentation for your product, enter your model

number (SM24TAT2DPA) in the “Search” box at our website at https://www.transition.com.

For Transition Networks Drivers, Firmware, Manual, etc. go to the Product Support webpage (no logon

required). For Transition Networks Application Notes, Brochures, Data Sheets, Specifications, etc. go to the

Support Library (no registration required).

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 4of 23

Contents

Safety Warnings and Cautions................................................................................................................. i

Compliance and Safety Statements........................................................................................................ 3

1. Introduction........................................................................................................................................ 5

Overview ............................................................................................................................................. 5

Front Panel.......................................................................................................................................... 5

LED Descriptions............................................................................................................................ 5

Mode/Reset button.......................................................................................................................... 7

Back Panel.......................................................................................................................................... 8

2. Installation....................................................................................................................................... 9

Package Contents............................................................................................................................. 10

Mounting the Switch in a 19-inch Rack..............................................................................................11

Mounting the Switch on Desk or Shelf.............................................................................................. 12

Connecting the AC Power Cord........................................................................................................ 12

Installing SFP Modules ..................................................................................................................... 13

Connecting Console Port.................................................................................................................. 13

3. Initial Configuration via Web GUI .................................................................................................. 14

Initial Switch Configuration Procedure.............................................................................................. 14

4. Troubleshooting .............................................................................................................................. 16

5. Specifications .................................................................................................................................. 39

Hardware Specifications ................................................................................................................... 39

Software Specifications....................................................................................................................... 2

6. Service, Warranty & Tech Support................................................................................................. 43

Warranty............................................................................................................................................ 43

Contact Us......................................................................................................................................... 44

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 5of 23

1. Introduction

Overview

The Transition Networks SM24TAT2DPA L2+ Managed PoE+ Switch provides

high-performance, IEEE-compliant network solutions. They include powerful management

features that can boost performance, and increase productivity. This manual describes

hardware installation and basic troubleshooting for these managed switches.

Front Panel

The SM24TAT2DPA switch front panel has system and port LEDs for installation and

troubleshooting and the Mode/Reset button.

The SM24TAT2DPA front panel is shown and described below.

LED Descriptions

The LEDs on the front panel provide users with switch status checking and monitoring.

The three types of LEDs are System, Mode, and Port Status. The following section details the

functions and descriptions of the LED indicators.

System LED

The System LED indicates if the switch is powered up correctly or not, or, indicates if there is a

system alarm triggered for troubleshooting.

LED Color State Description

System

Green On The switch is powered ON correctly.

Off The switch is not receiving power.

Red On An abnormal state, such as exceeding

operating temperature range, has been

detected in the switch.

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 6of 23

Mode LEDs

The Mode LEDs indicate the mode of all RJ45/SFP ports on the switch. You can press the

Mode/Reset button sequentially to switch between the two different modes

(Link/Activity/Speed mode and PoE mode).

LED Color State Description

Link/Act/Speed Green On The Port Status LEDs are displaying link

status, network activity and speed of each

port.

PoE Green On The RJ45 Port Status LEDs are displaying

PoE

powering status of each port.

Press and hold the Mode/Reset button for less than 2 seconds to change LED modes

(Link/Act/Speed Mode or PoE Mode); you can check the port status by reading the LED

behaviors per the table below.

Port Status LEDs

indicates the current status of each RJ45/SFP port. You can check these LEDs to understand the

port status in different modes, after changing the mode by pressing the Mode/Reset button.

When Link/Act/Speed Mode LED Lit

LED Color State Description

RJ45

Ports

Green On

The port is enabled and established a link to connected device,

and the connection speed is 1000Mbps.

Green Blinking

The port is transmitting/receiving packets, and the connection

speed is 1000Mbps.

Amber On

The port is enabled and established a link to the connected

device, and the connection speed is 10/100Mbps.

Amber Blinking

The port is transmitting/receiving packets, and the connection

speed is 10/100Mbps.

-- Off The port has no active network cable connected, or it is not

established a link to connected device. Otherwise, the port

may have been disabled through the switch user interface.

SFP

Ports

Green On

The port is enabled and established a link to connected device,

and the connection speed is 1000Mbps.

Green Blinking

The port is transmitting/receiving packets, and the connection

speed is 1000Mbps.

Amber On

The port is enabled and established a link to connected device,

and the connection speed is 100Mbps.

Amber Blinking

The port is transmitting/receiving packets, and the connection

speed is 100Mbps.

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 7of 23

-- Off The port has no active network cable connected, or it is not

established a link to connected device. Otherwise, the port

may have been disabled through the switch user interface.

When PoE Mode LED Lit

LED Color State Description

RJ45

Ports

Green On The port is enabled and supplying power to connected device.

Amber On

An abnormal state, such as overload status, has been detected

in the switch.

-- Off

The port has no active network cable connected, or it is not

connected a PoE PD device. Otherwise, the port may have been

disabled through the switch user interface.

Mode/Reset button

Press the Mode/Reset button for a specific period of time to perform these tasks:

□Change Port Status LED Mode: to read the port status correctly in the two different modes

(Link/Act/Speed mode or PoE mode).

□Reset the Switch: to reboot and get the switch back to the previous configuration settings saved.

□Restore the Switch to Factory Defaults: to restore the original factory default settings back to the

switch.

Note: The table below describes the task being performed by reading the LED behaviors while pressing

the Mode/Reset button. Once the LED behaviors are correctly displayed, you may release the button.

Table 1: Mode/Reset Button Descriptions

Task to Perform Press the Button for SYS LED

Behavior Port Status LED Behavior

Change LED Mode 0 ~ 2 seconds ON

Green LED status will change based on the

mode selected.

Reset the Switch 2 ~ 7 seconds Blinking

Green All LEDs OFF

Restore to Defaults 7 ~ 12 seconds Blinking

Green All LEDs Stay ON

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 8of 23

Back Panel

The SM24TAT2DPA back panel is shown below.

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 9of 23

2. Installation

CAUTION:

Circuit devices are sensitive to static electricity, which can damage their delicate

electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static

electrical charge. To protect your device, always:

•Touch the metal chassis of your computer to ground the static electrical charge before you pick up the

circuit device.

•Pick up the device by holding it on the left and right edges only.

•If you need to connect an outdoor device to this device with cable then you must add an arrester on

the cable between outdoor device and this device.

Fig. Add an arrester between outdoor device and this switch

NOTE:The switch is an indoor device; if it will be used in an outdoor environment or

connects with some outdoor device, then it must use a lightning arrester to protect the switch.

ARNING

Self-demolition on Product is strictly prohibited. Damage caused by self-demolition will be charged

for repairing fees.

Do not place product outdoors or where sandstorms occur.

Before installation, make sure input power supply and product specifications are compatible to each

other.

To reduce the risk of electric shock, disconnect all AC or DC power cords to completely remove

power from the unit.

Before importing / exporting configuration please make sure the firmware version is the same.

After firmware upgrade, switch automatically moves configuration to latest firmware version.

Warning: this case must be grounded. No DC input may be grounded. The SM24TAT2DPA is compliant with 802.3at

in Environment A when using an isolated power supply. For 802.3at Environment B applications, use mid-span injector

(s), e.g. MIL-L100i, L1000i-at, between this switch’s PSE port and link partner PD port.

Transition Networks SM24TAT2DPA Install Guide

33702 Rev. A https://www.transition.com Page 10 of 23

Package Contents

Verify that you received these iterms.

SM24TAT2DPA GbE Management Switch

Four adhesive rubber feet

Mounting Accessory (for 19“Rack Shelf, Optional)

Quick Start Guide

AC Power cord

Console cable

Save the packaging for possible future use.

Inhaltsverzeichnis

Andere Transition Networks Schalten Handbücher

Transition Networks

Transition Networks MIL-SEM24T4GPA Bedienungsanleitung

Transition Networks

Transition Networks SISPM1040-582-LRT Bedienungsanleitung

Transition Networks

Transition Networks SM24TBT2DPA Bedienungsanleitung

Transition Networks

Transition Networks SM12DP2XA Bedienungsanleitung

Transition Networks

Transition Networks SISTM1040-262D-LRT Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-0403 Bedienungsanleitung

Transition Networks

Transition Networks SM24T6DPA Bedienungsanleitung

Transition Networks

Transition Networks MIL-S4800 Bedienungsanleitung

Transition Networks

Transition Networks SM24TAT4XA Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-0400 Bedienungsanleitung

Transition Networks

Transition Networks SM8TAT2SA Bedienungsanleitung

Transition Networks

Transition Networks SISPM1040-3-L Series Bedienungsanleitung

Transition Networks

Transition Networks SESPM1040-541-LT Series Bedienungsanleitung

Transition Networks

Transition Networks SISTF101X-241-LRT Bedienungsanleitung

Transition Networks

Transition Networks E-FX-HB-0800 Bedienungsanleitung

Transition Networks

Transition Networks SM8TAT2SA-DC Bedienungsanleitung

Transition Networks

Transition Networks SM24DPB Bedienungsanleitung

Transition Networks

Transition Networks SM8TAT2SA-DC Bedienungsanleitung

Transition Networks

Transition Networks SM24DPB Bedienungsanleitung

Transition Networks

Transition Networks E-TBT-HB-1600 Bedienungsanleitung

Transition Networks

Transition Networks SISPM1040-3166-L Bedienungsanleitung

Transition Networks

Transition Networks SISGM1040-284-LRT Bedienungsanleitung

Transition Networks

Transition Networks SISTG1040-242-LRT Bedienungsanleitung

Transition Networks

Transition Networks SM24DPa Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung