Travis Industries 564 HO Bedienungsanleitung

564 HO Fireplace

Listed by

AS 4553-2008

GMK10022

IAPMO-R&T OCEANA

Operation - Maintenance

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Owner's Manual

Dragon Wholesaling Pty. Ltd.

Unit 2, 16 Lexington Drive

Bella Vista NSW 2153

Australia

2 Introduction

Introduction

We welcome you as a new owner of a 564 HO gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

heater and save the manual for future reference.

Important Information

No other 564 HO gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 564 HO GSR Fireplace

Serial Number:

Purchase Date:

Purchased From:

lopi.com.au

Or, mail your warranty card to:

Dragon Wholesaling Pty. Ltd.

Unit 2, 16 Lexington Drive

Bella Vista NSW 2153

Australia

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

Installation requirements are printed in the 564 HO GSR Installation Manual (part #

100-01327). All requirements in the installation manual must be met.

Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

The fireplace is designed to operate on natural gas, or propane (LP).

All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents



Introduction ...................................................2

Important Information...................................2

Installation Warnings....................................2

Table of Contents..........................................3

Features .........................................................3

Heating Specifications..................................3

Before You Begin..........................................6

Remote Set-Up...............................................6

Verify the Insert is plugged in..............................6

Synchronize the Transmitter to the Receiver ......6

Starting the Fireplace for the First Time.....6

Direct Operation............................................7

Accent Light...................................................7

Adjusting the Blower Speed ........................8

Continuous Pilot / GreenSmart™ Pilot

Switch.............................................................8

Remote Operation.........................................9

Changing the Display to Celcius (C)....................9

Display Overview ................................................9

Listen for the “Beep”............................................9

Manual On-Off / Smart Thermostat / Standard

Thermostat........................................................10

Mode Controls (Flame, Comfort Control) ..........11

Flame Height........................................................ 11

Comfort Control (rear burner)............................... 11

Normal Operating Sounds..........................12

Normal Operating Odors ............................12

Low Battery Indicator .................................13

Transmitter Batteries.........................................13

Receiver Batteries.............................................13

Child Proof Feature.....................................13

Power Outages............................................13

Maintaining Your Fireplace's Appearance13

Battery Replacement..................................14

Accent Light Replacement.........................15

Lower Bulbs ......................................................15

Upper Bulb........................................................15

Yearly Service Procedure...........................17

Grill Installation and Removal ...................18

Face Installation and Removal ..................19

Glass Frame Removal and Installation.....20

Glass Frame Removal and Installation

(continued)...................................................21

Log Set Installation.....................................22

Log Set Overview..............................................22

Glass Cleaning..................................................22

Troubleshooting Table...............................23

Wiring Diagrams .........................................24

Replacement Parts List..............................24

CONDITIONS & EXCLUSIONS ...................25

IF WARRANTY SERVICE IS NEEDED: ......25

Index .................................................................26

Features

Works During Power Outages (battery backup)

GreenSmart™ Thermostat / Remote Control

Realistic "Wood Fire" Look

Standard Blowers for Effective Heat Distribution

Built-In Accent Light (night light)

Built-In Control Panel Light

Standing or Intermittent (GreenSmart) Pilot

Convenient Operating Controls

Variable-Rate Heat Output

Low Maintenance

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square meters)* Up to 158 Up to 158

Maximum MJ Input Per Hour 35.0 35.0

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation.

Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Gas





Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.

Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included fiber

logs).

If the fiber logs become

damaged, replace with Travis

Industries log set.

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Dragon Wholesaling grants no

warranty, implied or stated, for

the installation or maintenance

of your heater, and assumes

no responsibility of any

consequential damage(s).



This

Manual

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Remote Set-Up

Verify the Insert is plugged in

The insert should be plugged in before synchronizing the remote.

Synchronize the Transmitter to the Receiver

The transmitter will need to be synchronized to the receiver before the remote will work correctly.

Synchronizing is done in the following two steps below (see Figure 1):

a) Press the PRG (Program) button on the receiver using a paperclip or equivalent device (receiver

will beep 3 times).

b) Press the “ON” button on the transmitter (receiver will beep 4 times).

Figure 1

NOTE: If power is cut off to the receiver for an extended period of time, you may need to re-synchronize

the remote.

Starting the Fireplace for the First Time

Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

Condensation may appear on the glass each time you start the fireplace - this is normal.

Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

Certain installations use a remote, thermostat, or wall switch to turn the fireplace on and off. If this is

the case, leave the ON/OFF switch "ON".

Verify the power backup and control light batteries are installed (see page 14).

Display Fahrenheit or Celsius

With the system in the “OFF” position, press both the MODE and THERMOSTAT buttons

simultaneously to toggle between Fahrenheit (F) and Celsius (C).

Figure 2

°F

====

"Beep"

“Beep”

"Beep"

Operation 7

Direct Operation

The fireplace may be directly operated from the receiver. The three positions are below (see Figure 3):

ON – Burner turns on (regardless of transmitter settings).

OFF – Burner turns off (regardless of transmitter settings).

REMOTE – Burner is controlled by the transmitter.

Figure 3

NOTE: When the receiver switch is turned to ON or OFF, the mode settings (Flame Height, Comfort

Control) will remain in the same state as before the switch was moved (i.e.: the receiver “remembers” the

last setting). If you wish to adjust the mode settings use the transmitter mode button to adjust the settings

(see “Mode Controls” on page 11). The thermostat and burner on/off operating functions will not work on

the transmitter.

Accent Light

This fireplace has a built-in accent light that may be turned on and off and dimmed to your preference.

Turn the knob to achieve the desired light output.

REMOTE

OFF PRG

ACCENT LIGHT

OFF

HIGH

LOW

OFF LOW HIGH

8 Operation

Adjusting the Blower Speed

The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to

temperature (approximately 15 minutes after starting). See the illustration below for instructions on

adjusting the blower speed.

NOTE: With the rear burner off (comfort control), the heater may not become hot enough for the

blower to turn on.

Continuous Pilot / GreenSmart™ Pilot Switch

This fireplace may run with the pilot continuously running or in GreenSmart (intermittent) mode. For most

homeowners, the GreenSmart mode is preferred (this saves fuel, doesn’t give off un-needed heat).

However, in some situations the homeowner may prefer to switch the fireplace to continuous pilot. The

most typical reasons for switching to continuous pilot are:

Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly,

and the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot.

This will create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.

Excessive Condensation on Glass After Startup – certain installations may encounter excessive

fogging on the window after stuartup (not just the first time the fireplace was started). This is an

aesthetic condition that may be remedied by switching the fireplace to continuous pilot.

Cold Glass or Fireplace Front – in very cold conditions you may notice that the fireplace front and

glass become very cold. To remedy this, switch the fireplace to continuous pilot.

Frequent On / Off Operation – if you are frequently turning the fireplace on and off, you may wish to

leave it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.

BLOWER

OFF

HIGH

LOW

CONTINUOUS

PILOT

GREEN SMART

PILOT

Operation 9

Remote Operation

Once the receiver is switched to “REMOTE” the transmitter operates the fireplace. Once you understand

how the transmitter works, you will be able to operate your fireplace quickly and easily.

Changing the Display to Celcius (C)

With the remote off, press the thermostat and mode button simultaneously. This will toggle between

Fahrenheit and Celcius.

Display Overview

The transmitter display has four main sections (see Figure 4).

Figure 4

Listen for the “Beep”

Each time you press a button on the transmitter that controls the fireplace, a “beep” will come from the

fireplace. When you change thermostat target settings the fireplace will not beep.

NOTE: When the receiver batteries start to get low, the receiver will beep intermittently. When the

batteries are nearly depleted, the receiver will no longer beep. See “Receiver Batteries” on page 13).

MAX

Thermostat Display

Room Temperature Display

Read-Out (Thermostat Setting, Function, etc.)

Mode Display (Flame Height, Comfort Control)

10 Operation

Manual On-Off / Smart Thermostat / Standard Thermostat

Use the thermostat button to cycle through the three thermostat settings (see Figure 5).

Figure 5

MANUAL ON/OFF – The burner will turn on and off using the remote (see Figure 6). Press the

On/Off button to control the burner. When off, the display will only show the current temperature.

Figure 6

SMART THERMOSTAT – While in smart thermostat, the transmitter will control the burner to

achieve the target temperature (see Figure 7 below). Flame height will be adjusted up or down to

allow operation without turning the burner on and off (also called “smart modulation). To adjust

the target temperature, press the up and down buttons until a suitable temperature is achieved.

Figure 7

STANDARD THERMOSTAT - While in standard thermostat setting, the transmitter will turn the

burner on and off to achieve the target temperature (see Figure 8 below). To adjust the target

temperature, press the up and down buttons until a suitable temperature is achieved.

Figure 8

NOTE: if the transmitter batteries go dead while in thermostat setting (standard or smart), the appliance

will shut off after approximately 24 hours.

OFF

ON SMART

Look here for the

thermostat setting. Press the thermostat button to cycle

through the thermostat settings.

OFF

When in manual setting, the

word “OFF” will appear here.

MAX

When in smart thermostat

setting, the word “SMART”

will appear here.

This is the target temperature

on the read-out. Use the up

or down buttons to adjust the

target temperature.

SMART

When in standard thermostat

setting, the word “ON” will

appear here.

This is the target temperature

on the read-out. Use the up

or down buttons to adjust the

target temperature.

Andere Handbücher für 564 HO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR2 NB Bedienungsanleitung

Travis Industries

Travis Industries X-96 Bedienungsanleitung

Travis Industries

Travis Industries House of Fire 4237 EG Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair CoolSmart TV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries 864 See Through Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GS Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Flush Plus Bedienungsanleitung

Travis Industries

Travis Industries 616 Diamond-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB Bedienungsanleitung

Travis Industries

Travis Industries DVL EF II Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch