Travis Industries 864 See Through Bedienungsanleitung

864 See Through (ST)

GreenSmart™ Fireplace

•Operation

•Maintenance

Tested and Listed by

OMNI-Test Laboratories, Inc.

Portland, Oregon

Report # 028-F-84-5

ANSI Z21.88a-2003

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an aftermarket permanently

located, manufactured home (USA only) or mobile home, where

not prohibited by local codes.

This appliance is only for use with the type(s) of gas indicated on

the rating plate. A conversion kit is supplied with the appliance.

Owner's Manual

www.travisproducts.com

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

2 Introduction

Introduction

We welcome you as a new owner of a 864 See Through (ST) gas fireplace. This manual details operation

and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating

your heater and save the manual for future reference.

Important Information

No other 864 ST gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 864 ST GS Fireplace

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

•Installation requirements are printed in the 864 ST GS Installation Manual (part # 100-

01217). All requirements in the installation manual must be met.

•Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

•This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

•This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

•In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

•The fireplace is designed to operate on natural gas, or propane (LP).

•All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

•Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents

Introduction and Important Information

Introduction.........................................................................2

Important Information..........................................................2

Installation Warnings...........................................................2

Features..............................................................................3

Heating Specifications.........................................................3

Safety Precautions

Safety Precautions..............................................................4

Operation

Before You Begin................................................................6

Location of Controls............................................................6

Starting the Fireplace for the First Time..............................7

Turning the Fireplace On and Off........................................7

Comfort Control...................................................................7

Adjusting the Flame Height.................................................8

Accent Light........................................................................8

Adjusting the Optional Blower Speed..................................9

Continuous Pilot / GreenSmart™ Pilot Switch.....................9

Normal Operating Sounds...................................................10

Normal Operating Odors.....................................................10

Maintenance

Maintaining Your Fireplace's Appearance........................... 11

Battery Replacement .......................................................... 11

Accent Light Replacement.................................................. 12

Yearly Service Procedure ................................................... 12

Grill Installation and Removal ............................................. 13

Face Installation and Removal............................................ 14

Glass Frame Removal and Installation............................... 15

Log Set Installation ............................................................. 17

Glass Cleaning ................................................................... 27

Troubleshooting Table........................................................ 28

Wiring Diagram.................................................................. 29

Replacement Parts List....................................................... 31

Warranty

Warranty............................................................................. 29

Optional Equipment

Optional Equipment List...................................................... 33

Index

Index................................................................................... 34

Features

•Works During Power Outages (battery backup)

•Optional GreenSmart™ Thermostat / Remote Control

•Realistic "Wood Fire" Look

•Optional Blower for Effective Heat Distribution

•Built-In Accent Light (night light)

•Built-In Control Panel Light

•Standing or Intermittent (GreenSmart) Pilot

•Convenient Operating Controls

•Variable-Rate Heat Output

•Low Maintenance

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* Up to 1,500 (139 sq. M) Up to 1,500 (139 sq. M)

Maximum BTU Input Per Hour 37,500 (39.5 MJ) 37,500 (39.5 MJ)

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and

at least annually by a qualified service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Gas

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.





Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.





Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.



This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included fiber

logs).

If the fiber logs become

damaged, replace with Travis

Industries log set.

This

Manual

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Travis Industries, Inc. grants

no warranty, implied or stated,

for the installation or

maintenance of your heater,

and assumes no responsibility

of any consequential

damage(s).

6 Operation

Before You Begin

•Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Location of Controls

Lift up and swing the lower

grill down to acces the area

below the firebox.

Swing the concelament cover up and

slide it back to expose the controls.

BLOWER

OFF

HIGH

LOW

ACCENT LIGHT

HIGH

LOW

FLAME ADJUST CONTINUOUS

PILOT

GREEN SMART

PILOT

COMFORT

CONTROL MAIN

BURNER

OFF

HIGH

LOW

BATTERY

HOLDER

An instruction card for

operating the fireplace is

attached to the inside of the

fireplace here. Replace it for

easy reference.

Optional Blower Control This knob controls the speed of the optional internal convection blower

that pushes heated air into the room.

Accent Light This knob controls the accent lights located behind the logs.

Flame Adjust Knob This knob controls the flame height from low ("LO") to high ("HI").

Continuous Pilot --

GreenSmart Pilot This switch controls how the pilot flame works. See the section

“Continuous Pilot / GreenSmart Pilot” for details.

Comfort Control This switch turns the rear burner on and off.

AA Battery Holder This holder contains 4 AA batteries that allow the fireplace to operate

during power outages.

Main Burner This switch turns the fireplace burners on and off.

Operation 7

Starting the Fireplace for the First Time

•Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

•Condensation may appear on the glass each time you start the fireplace - this is normal.

•Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

•Certain installations use a remote, thermostat, or wall switch to turn the fireplace on and off. If this is

the case, leave the ON/OFF switch "ON".

•Verify the power backup and control light batteries are installed (see page 11).

Turning the Fireplace On and Off

Use the main burner switch to turn the main burner on and off.

MAIN

BURNER

OFF

NOTE FOR REMOTES, THERMOSTATS, OR WALL SWITCHES:

The on/off switch on the fireplace may be required to be left in the ON or OFF position for the fireplace to

operate. Consult your installer or dealer for details.

•Do not place any combustible items on top of or directly in front of the fireplace, even temporarily. An

optional thermostat may start the fireplace causing a combustible item to ignite.

•If the fireplace turns on and off frequently while using the thermostat, you may want to adjust the

flame height down until it produces just enough heat needed.

Comfort Control

The rear portion of the burner may be shut off to lower the heat output and flame size from the burner

(this is called the comfort control). Use the comfort control switch to adjust this as desired.

COMFORT

CONTROL

8 Operation

Adjusting the Flame Height

This fireplace has an adjustable flame to tailor the look and heat output to your specific needs. It is

adjusted by turning the flame adjust knob.

HIGH

LOW

FLAME ADJUST

Accent Light

This fireplace has a built-in accent light that may be turned on and off and dimmed to your preference.

Turn the knob to achieve the desired light output.

NOTE FOR STAINLESS OR ENAMEL FIREBACKS

Because stainless or enamel firebacks are reflective, they may create unwanted glare or “lines”

if the accent light is turned to HIGH. We recommend keeping the accent light at a low level with

these unique firebacks.

ACCENT LIGHT

OFF

HIGH

LOW

OFF HIGHLOW

Operation 9

Adjusting the Optional Blower Speed

The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to

temperature (approximately 15 minutes after starting). See the illustration below for instructions on

adjusting the blower speed.

NOTE: With the rear burner off (comfort control), the heater may not become hot enough for the

blower to turn on.

BLOWER

OFF

HIGH

LOW

Continuous Pilot / GreenSmart™ Pilot Switch

This fireplace may run with the pilot continuously running or in GreenSmart (intermittent) mode. For most

homeowners, the GreenSmart mode is preferred (this saves fuel, doesn’t give off un-needed heat).

However, in some situations the homeowner may prefer to switch the fireplace to continuous pilot. The

most typical reasons for switching to continuous pilot are:

•Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly,

and the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot.

This will create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.

•Excessive Condensation on Glass After Startup – certain installations may encounter excessive

fogging on the window after stuartup (not just the first time the fireplace was started). This is an

aesthetic condition that may be remedied by switching the fireplace to continuous pilot.

•Cold Glass or Fireplace Front – in very cold conditions you may notice that the fireplace front and

glass become very cold. To remedy this, switch the fireplace to continuous pilot.

•Frequent On / Off Operation – if you are frequently turning the fireplace on and off, you may wish to

leave it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.

CONTINUOUS

PILOT

GREEN SMART

PILOT

10 Operation

Normal Operating Sounds

Gas Control Valve

As the gas control valve is turned

on and off you will hear a dull

clicking sound. This is the valve

opening up and shutting down.

Blower Snap Disk

This part can produce a clicking

sound as it turns the blower on

and off.

The appliance may creak with change of

temperature -- THIS IS NORMAL.

Pilot Assembly

The pilot flame will make a clicking

sound when starting up. If left on, it

will make a slight whisper sound.

Blower

This heater has an optional blower to push

heated air into the room. You will hear the

sound of air movement that increases as

the speed is increased.

Extinction Pops

It is not unusual, especially on Propane

(LP) appliances, to experience a "pop"

when the burner is shut off.

GreenSmart Receiver

The optional GreenSmart receiver will

beep when receiving commands from the

GreenSmart remote.

DC Converter

This device makes a light humm that

is audible in close proximity.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these areas

may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if

the appliance was left idle for a long period.

Andere Handbücher für 864 See Through

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 564 DF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 616 GSR2 Insert Bedienungsanleitung

Travis Industries

Travis Industries 36 CF ST Bedienungsanleitung

Travis Industries

Travis Industries 36 CF II Handbuch

Travis Industries

Travis Industries X-96 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 96900911 Bedienungsanleitung

Travis Industries

Travis Industries FIREPLACE XTRORDINAIR 864 HO EF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB Bedienungsanleitung

Travis Industries

Travis Industries Space Saver GreenSmart 2 564 Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Fireplace Bedienungsanleitung

Travis Industries

Travis Industries Spirit 300 GS Bedienungsanleitung

Travis Industries

Travis Industries 864 HO GS Bedienungsanleitung

Travis Industries

Travis Industries Small Flush Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Plus Insert Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR2 NB Insert Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch