Travis Industries 564 HO Bedienungsanleitung

· 564 HO 2 Fireplace ·

Tested and Listed by

ANSI Z21.88

CSA 2.33

Operation

Maintenance

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Owner's Manual

www.travisproducts.com

12521 Harbour Reach Drive

Mukilteo, WA 98275

2 Introduction

Introduction

We welcome you as a new owner of a 564 HO GSR2 gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

heater and save the manual for future reference.

Important Information

No other 564 HO GSR2 gas fireplace has the same

serial number as yours. The serial number is on the

listing label that is chained to the gas control valve.

This serial number may be needed in case you require

service.

Model: 564 HO GSR2 Fireplace

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

12521 Harbour Reach Drive

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

Installation requirements are printed in the 564 HO GSR2 Installation Manual (part #

100-01292). All requirements in the installation manual must be met.

Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

The fireplace is designed to operate on natural gas, or propane (LP).

All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents



Introduction 2

Important Information 2

Installation Warnings 2

Table of Contents 3

Features 3

Heating Specifications 3

Before You Begin 6

Remote Control Warnings ........................................ 6

Remote Set-Up 7

Verify the Switch is on “REMOTE” ......................7

Synchronize the Transmitter to the IFC...............7

Clearing the System Memory ...................................7

Location of Controls 8

Direct Operation 9

Starting the Fireplace for the First Time 9

Intermittent/Continuous Pilot 10

Switching from Intermittent (IPI) to Continuous

Pilot (CPI)..........................................................10

Remote Operation 11

Display Overview ..............................................11

Listen for the “Beep”..........................................11

Manual On-Off / Smart Thermostat / Standard

Thermostat 12

Mode Controls (Flame, Blower, Light, Comfort

Control) 13

Flame Height .......................................................... 13

Blower Speed .........................................................13

Mode Controls - continued 14

Accent Light............................................................14

Comfort Control (rear burner).................................14

Display Fahrenheit or Celsius 14

Low Battery Indicator 15

Transmitter Batteries.........................................15

IFC Batteries.....................................................15

Battery Replacement 15

Battery Installation.............................................15

Transmitter Battery Installation..........................15

Power Outages 15

Child-Proof Feature 16

Normal Operating Sounds 16

Normal Operating Odors 16

Maintaining Your Fireplace's Appearance 16

Accent Light Replacement 17

Lower Bulbs ......................................................17

Upper Bulb........................................................17

Yearly Service Procedure 19

Grill Installation and Removal 20

Face Installation and Removal 21

Glass Frame Removal and Installation 22

Glass Frame Removal and Installation

(continued) 23

Media Installation 24

Log or Stone Set ...............................................24

Glass Cleaning 24

Troubleshooting Table 25

Wiring Diagram 26

Replacement Parts List 26

CONDITIONS & EXCLUSIONS 27

IF WARRANTY SERVICE IS NEEDED: 27

Features

Works During Power Outages (battery backup)

GreenSmart™ 2 Thermostat / Remote Control

Multiple Media Options

Standard Blowers for Effective Heat Distribution

Built-In Accent Light (night light)

Standing or Intermittent (GreenSmart) Pilot

Convenient Operating Controls

Variable-Rate Heat Output

Low Maintenance

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* Up to 1,700 Up to 1,700

Maximum BTU Input Per Hour 35,000 35,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation.

Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Gas





Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.

Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included fiber

logs).

If the fiber logs become

damaged, replace with Travis

Industries log set.

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Travis Industries, Inc. grants

no warranty, implied or stated,

for the installation or

maintenance of your heater,

and assumes no responsibility

of any consequential

damage(s).



This

Manual

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Remote Control Warnings

KEEP BATTERIES AND COVER

INSTALLED AT ALL TIMES

The remote control system requires the batteries and battery cover to

remain in place at all times. Once the batteries or cover are removed, the

system may re-start in standing pilot mode. If this occurs when the heater is

in Remote Mode, you will not be able to turn the heater off manually from

the battery box.

If you need to replace dead batteries, make sure to turn the appliance

off before removing the batteries.

NOTE:If the batteries go dead, the system will operate normally as long

as household power (120v AC) is present.

The transmitter and IFC are radio frequency devices. Placing the transmitter in or near

metal may severely reduce the signal range.

Turn off the main gas supply to the appliance during appliance installation or maintenance.

During appliance installation or maintenance or in case of remote control malfunction turn

off the main gas supply.

Operation 7

Remote Set-Up

Verify the Switch is on “REMOTE”

The battery holder has a switch built into it (see Figure 1). This switch must remain in the REMOTE

position for the remote to operate.

Figure 1

Synchronize the Transmitter to the IFC

The transmitter will need to be synchronized to the IFC (Integrated Fireplace Control) before the remote

will work correctly. Synchronizing is done in the following two steps below (see Figure 2):

1. Press the PRG (Program) button on the battery box (IFC will beep 3 times).

2. Press the “ON” button on the transmitter (IFC will beep 3 times).

Figure 2

NOTE: If power is cut off to the IFC for an extended period of time, you may need to re-synchronize the

remote.

Clearing the System Memory

This appliance uses an Integrated Fireplace Control (IFC) to store the unique code for the remote control.

If you wish to clear the system memory, MAKE SURE GAS IS TURNED OFF TO THE APPLIANCE then

press the PRG (Program) button for 10 seconds. The pilot will start to spark repeatedly, signifying all

system memory has been cleared. The system will return to its original configuration: a remote will need

to be synchronized; and, the system will operate under continuous pilot mode.

ON REMOTE OFF

°F

"Beep"

8 Operation

Location of Controls

ON REMOTE OFF

Swing the access door and control

cover down to access the battery

holder / switch.

Most features will be controlled

by the included remote.

°F

Operation 9

Direct Operation

The fireplace may be directly operated from the battery holder. The three positions are below (see Figure 3):

ON – Burner turns on (regardless of transmitter settings).

OFF – Burner turns off (regardless of transmitter settings).

REMOTE – Burner is controlled by the transmitter.

Figure 3

NOTE: When the battery holder switch is turned to ON or OFF, the mode settings (Flame Height, Comfort

Control) will remain in the same state as before the switch was moved (i.e.: the IFC “remembers” the last

setting). If you wish to adjust the mode settings use the transmitter mode button to adjust the settings

(see “Mode Controls” on page 13). The thermostat and burner on/off operating functions will not work on

the transmitter.

Starting the Fireplace for the First Time

Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

Condensation may appear on the glass each time you start the fireplace - this is normal.

Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

Certain installations use a remote, thermostat, or wall switch to turn the fireplace on and off. If this is

the case, leave the ON/OFF switch "ON".

Verify the power backup batteries are installed (see page 15).

ON REMOTE OFF

10 Operation

Intermittent/Continuous Pilot

This heater may run with the pilot continuously running or in intermittent mode. For most homeowners,

the intermittent mode is preferred (this saves fuel, doesn’t give off un-needed heat). However, in some

situations the homeowner may prefer to switch the heater to continuous pilot. The most typical reasons

for switching to continuous pilot are:

Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly,

and the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot.

This will create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.

Excessive Condensation on Glass After Startup – certain installations may encounter excessive

fogging on the window after startup (not just the first time the heater was started). This is an aesthetic

condition that may be remedied by switching the heater to continuous pilot.

Cold Glass or Heater Front – in very cold conditions you may notice that the heater front and glass

become very cold. To remedy this, switch the heater to continuous pilot.

Frequent On / Off Operation – if you are frequently turning the heater on and off, you may wish to

leave it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.

Switching from Intermittent (IPI) to Continuous Pilot (CPI)

The pilot mode on this appliance is adjusted using the remote. With the remote in the off position

(thermostat off, manual off), follow the directions below to adjust the pilot mode.

Figure 4

Press the "MODE" button

when the appliance is off to

adjust the IPI/CPI.

NOTE: This icon appears

when the appliance is in

CPI mode. Press the "UP" button

to activate CPI mode.

Press the "DOWN" button

to activate IPI mode.

Andere Handbücher für 564 HO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries GREEN SMART 864 Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR2 NB Insert Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries 6015 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 HH Bedienungsanleitung

Travis Industries

Travis Industries 430 Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries Avalon Pendleton 745 Bedienungsanleitung

Travis Industries

Travis Industries Large Flush Wood Insert Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 96900911 Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries DVS FIREPLACE Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung