Travis Industries Xtreme 6020 Bedienungsanleitung

Xtreme 6020 Fireplace

•Natural Gas - 98500325

•LP (Propane) - 98500326

Built-In Direct-Vent Power-Vent Fireplace

This appliance is only for use with the type(s) of

gas indicated on the rating plate.

WARNING: If the information in these instructions is not followed exactly, a

fire or explosion may result causing property damage, personal

injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

Tested and Listed by

Report # 3183426

Owner’s Manual

Installer: After installation give this manual to the home-

owner and explain operation of this fireplace.

4100329

www.travisproducts.com

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

2 Introduction

Introduction

We welcome you as a new owner of a Xtreme 6020 gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

fireplace and save the manual for future reference.

Important Information

No other Xtreme 6020 gas fireplace has the same

serial number as yours. The serial number is on the

listing label that is chained near the glass frame. This

serial number may be needed in case you require

service.

Model: Xtreme 6020 Fireplace

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your fireplace. Do not mail your

Bill of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

•Installation requirements are printed in the Xtreme 6020 Installation Manual (part #

100-01246). All requirements in the installation manual must be met.

•Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

•This fireplace must be installed by a qualified installer who has gone through a

training program for the installation of direct vent gas appliances.

•This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

•The fireplace is designed to operate on natural gas, or propane (LP).

•All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

•Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents

Introduction and Important Information

Introduction.........................................................................2

Important Information..........................................................2

Installation Warnings...........................................................2

Features..............................................................................3

BTU Specifications..............................................................3

Safety Precautions

Safety Precautions..............................................................4

Operation

Before You Begin................................................................6

Starting the Fireplace for the First Time..............................6

Remote Control...................................................................6

Setting Up the Remote (Time, Day, Swing, °F/°C)..............7

Remote Synchronization.....................................................8

The Two Modes of Operation..............................................9

Remote Functions...............................................................10

PROGRAM FUNCTION (7 day thermostat).......................11

Continuous Pilot – NOT USED FOR THIS FIREPLACE.....12

Normal Operating Sounds...................................................12

Normal Operating Odors.....................................................12

Power Outages ...................................................................12

Child Protection Feature .....................................................12

Maintenance

Yearly Service Procedure ...................................................13

Glass Cleaning....................................................................13

Accent Light Bulb Replacement..........................................13

Replacement Parts List.......................................................14

Wiring Diagram ...................................................................15

Warranty

Warranty .............................................................................16

Index

Index...................................................................................18

Features

•Optional Extr-Room Blower for Heat Distribution

•Built-In Accent Lights

•Convenient Operating Controls

•Low Maintenance

BTU Specifications

Natural Gas Propane

Maximum BTU Input Per Hour 90,000 90,000

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The fireplace should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

CH 4

- or -

83H

This fireplace is either approved

for natural gas (NG) or for

propane (LP). Burning the

incorrect fuel will void the

warranty and safety listing and

may cause an extreme safety

hazard. Direct questions about

the type of fuel used to your

dealer or installer

Operate the fireplace according

to the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer for

service.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this fireplace as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the fireplace. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the fireplace be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the fireplace if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your fireplace and

what to expect.

Gas

Do not store or use gasoline or

other flammable liquids in the

vicinity of this fireplace.





Do not operate if any portion of

the fireplace was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Safety Precautions 5

Do not place clothing or other

flammable items on or near the

fireplace. Because this fireplace

can be controlled by a

thermostat there is a possibility

of the fireplace turning on and

igniting any items placed on or

near it.





Light the fireplace using the built-

in electronic igniter. Do not use

matches or any other external

device to light your fireplace.

Allow the fireplace to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

fireplace.

Never remove, replace, modify or

substitute any part of the

fireplace unless instructions are

given in this manual. All other

work must be done by a trained

technician. Don't modify or

replace orifices.

Prior to removing the glass, shut

off gas to the appliance (or shut

off electricity to the fireplace).

This prevents any chance of

accidental burner ignition when

accessing the firebox.

This

Manual

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.



This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included fiber

logs).

If the fiber logs become

damaged, replace with Travis

Industries log set.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

fireplace.

Travis Industries, Inc. grants

no warranty, implied or stated,

for the installation or

maintenance of your fireplace,

and assumes no responsibility

of any consequential

damage(s).

Operate the fireplace according

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer for

service.

6 Operation

Before You Begin

•Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Starting the Fireplace for the First Time

•You may wish to burn the fireplace at a high setting for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

•Condensation may appear on the glass each time you start the fireplace - this is normal.

•Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

Remote Control

The remote control controls all of the functions on the fireplace. It can be placed inside the holder and

hung on the wall or it can be placed near the fireplace.

Set

Mode

Operation 7

Setting Up the Remote (Time, Day, Swing, °F/°C)

The remote will need to be set up when first started or when the batteries were removed or replaced.

Follow the directions below to set the time, day, and other settings.

A. Press and hold the “Set” and “Up” arrow buttons for 5 seconds.

B. The “ROOM” temperature will blink. Use the arrow keys until °F (fahrenheit) or °C (celcius) is

displayed. Press the “Set” button to set the temperature scale.

C. The “SWING” number will blink. This setting is not required when using this fireplace.

D. The day of the week will blink. Use the arrow keys to select the correct day. Press the “Set” button

to set the day.

E. The hour of the day will blink. Use the arrow keys to select the correct hour. Press the “Set” button

to set the hour.

F. The minute of the hour will blink. Use the arrow keys to select the correct minute. Press the “Set”

button to set the minute.

G. The AM / PM designation will blink. Use the arrow keys to select the correct setting. Press the “Set”

button to set AM / PM.

8 Operation

Remote Synchronization

The remote control is shipped pre-synchronized to the fireplace. If, however, the remote does not work

with the fireplace, follow the directions below to synchronize the remote to the fireplace.

NOTE: The fireplace must have power and the transmitter must have batteries to complete this process.

WARNING: Shut the gas off to the fireplace prior to conducting this process.

1 The “Learn” switch is accessed by removing a cover plate over the junction box. Inside the junction

box to the side of the rheostat you will find the “Learn” switch (see the illustration below).

2 Press the “Learn” button once. The fireplace will beep once.

3 Press the “Mode” button on the remote. The fireplace will beep five times to indicate

synchronization.

Set

Mode

Wall

Beep

Beep, Beep,

Beep

NOTE: Re-setting the Receiver Module

If the receiver module fails to synchronize with the remote or wall switch after two attempts, you should

re-set the receiver module. To do this, hold down the LEARN button for approximately 10 seconds until

the receiver beeps 3 times. This indicates the receiver has been re-set and can be synchronized using

the instructions above.

Operation 9

The Two Modes of Operation

Manual Mode

In manual mode you can turn the fireplace on and off by pressing the “Mode” button until “ON” or “OFF”

appears on the remote.

Set

Mode

Set

Mode

Thermostat Mode

Thermostat mode is not used on this fireplace.

Because the fireplace is not intended for use as a

fireplace, do not use the thermostat mode.

Continue to press the “MODE” button on the

remote until “ON” or “OFF” appear.

Set

Mode

10 Operation

Remote Functions

Switching Between Remote Functions

By pressing the Function “FN” button, you can scroll through the following 7 functions on the remote:

MAIN (Main Burner)

This function will only appear when burner is on.

The burner flame height may be adjusted from low “1” to high “3”. Use the arrow keys to adjust the

setting. Once the desired setting is made, the remote will alter the setting after approximately 8

seconds (and the remote display will stop blinking).

NOTE: The fireplace must be on (either manual or thermostat) to adjust the main burner.

REAR

This function is not used on this fireplace.

FAN

This function may be used with an optional power heat duct.

LIGHT

This function adjusts the built-in accent light.

The built-in accent light located inside the fireplace may be adjusted from “OFF” to high “3” (a total of 4

settings). Use the arrow keys to adjust the setting. Once the desired setting is made, the remote will

alter the setting after approximately 8 seconds (and the remote display will stop blinking).

AUX (Optional 120V Switch)

This function turns the lights below the burner on and off.

TIMER

This function allows the user to turn the fireplace on for a set period of time.

The timer function allows you to turn the fireplace on from 10 to 180 minutes. Use the arrow keys to

select the desired time. The fireplace will then turn off after the specified time. Once the desired

setting is made, the remote will alter the setting after approximately 8 seconds (and the remote display

will stop blinking).

NOTE: The fireplace must be in manual mode, and on, for the timer function to work.

PROGRAM (Programmable 7 day thermostat)

This function allows the user to program specific on/off, temperature, weekday and weekend settings

on the thermostat.

Set

Mode

Andere Handbücher für Xtreme 6020

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR Ember-Fyre Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 564 Montageanleitung

Travis Industries

Travis Industries 864 ST GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries Pro Builder Linear Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRVGreenSmart Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries 35 CB Australian Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVS Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Plus Bedienungsanleitung

Travis Industries

Travis Industries Large Flush Bedienungsanleitung

Travis Industries

Travis Industries Xtreme 6020 Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair CoolSmart TV Bedienungsanleitung

Travis Industries

Travis Industries 564 DF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Granite 99600200 Service-Handbuch

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch