TRENDnet TV-IP310PI Merkblatt

2440 Camino Ramon, Suite 125

San Ramon, CA 94583

Tel: (800)836-0199 Fax: (925)270-1894

Configure TRENDnet TV-IP310PI Day/Night Network Camera for

Cloud Recording, Remote Monitoring and Playback

Contents

Introduction .............................................................................................................................................. 2

Step 1: Connect Camera to the Network and Find Its IP Address ............................................................ 3

Step 2. Access Camera's Web-based Configuration Tool ......................................................................... 6

Step 3. Configure the Video / Image Profile (Resolution)......................................................................... 7

Step 4. Configure FTP Storage .................................................................................................................. 7

Step 5. Configure Events (Motion Detection and Snapshots) .................................................................. 8

5.1 Configure Motion Detection ........................................................................................................... 8

5.2 Configure Image Snapshot Settings ................................................................................................ 9

6. CameraFTP Viewer.............................................................................................................................. 10

Introduction

TRENDnet TV-IP310PI is a low-cost yet powerful PoE outdoor network camera. It supports

3MP image resolution, which is 50% higher than Full HD 1080P; it supports up to 100-feet night

vision, which is significantly better than most other IP cameras. The only drawback is it does not

support video clip recording.

If you need to monitor a very large outdoor site (such as a construction site), but you only need

to record one image every few seconds or minutes, then this camera is an ideal choice.

Basic camera information

Video / image resolution

2048x1536,1920x1080, 1280x800,1280x720

Audio recording

Image upload frequency

1 image per 1, 2, 3, 4, 5, 6 or more seconds.

Video frame rate

Cannot upload video clips to the cloud

Night-vision

Up to 100 feet (30m)

Image snapshot recording

Supported, supports 1-5 images/s and 1 image/N seconds

Video clip recording

Not Supported

Motion detection

Supported

Continuous recording

Supported

Supported video format

JPEG image only

Connection type

Ethernet cable, (PoE)

PoE (Power on Ethernet)

Yes

Indoor / outdoor

Outdoor

Lowest pricing (as of

8/4/2015)

$160

Note: This document is not designed to replace the product manual from the manufacturer. The

information provided is based on our knowledge of the model TRENDnet TV-IP310PI.It may

not be accurate or completely up-to-date. Users shall contact the manufacturer for all camera-

related issues and contact us only for CameraFTP-related (cloud service / FTP) issues.

The first two steps are camera related and are very trivial. If you have finished these basic steps,

you can skip Steps 1 and 2.

Step 1: Connect Camera to the Network and Find Its IP Address

Insert the Setup CD, follow the instructions to connect your camera. The TRENDnet TV-IP310PI supports

PoE. So usually you need a PoE switch, or you need a compatible power adaptor (not included).

Click Next, the wizard will start searching for the camera in the network. Within 1-2 minutes, it should

be able to find the camera in the network:

Select the camera and click Next

Select DHCP and click Next. If you are familiar with networking, you can also change its IP address to a

static IP address.

This camera has enhanced security. It requires you to change the default password as the first step. The

default username and password is admin / admin. You must change it.

After you changed your password, click Next, it will take a while for the camera to actually verify and

change the password. When done, it will display the following screen.

Don’t click Next yet. Click “here” instead. (If you already clicked Next, you need to run the Setup

program to reach the above screen again.)

After you click Here, it will launch a browser to access the camera’s configuration screens. See the

screenshot below:

Step 2. Access Camera's Web-based Configuration Tool

Now we have found the camera's IP address. The first step is to log on to the camera. Enter the camera’s

username and password, click Ok. It will go to the following screen:

If you have not installed the plug-in, you can install it for the live-view in your browser. For CameraFTP

service, since we offer cloud viewing, storage and playback, it is not required. You can click the

Advanced tab.

The Camera Name in this page should match the camera name you created on www.cameraftp.com.

Other than that, the CameraFTP service is generally not dependent on any parameters in the System

section of setup. You can quickly check this section and see if you need to configure anything.

Step 3. Configure the Video / Image Profile (Resolution)

Click Advanced --> Video --> Video Format, you can see the screenshot as follows:

This camera can only upload image snapshots, so only the resolution field needs to be configured.

The resolution to select is dependent on your subscription level. For this camera, the lowest resolution is

720P, so your CameraFTP subscription plan should not be lower than 1280x720.

Note: If you want to record video clips with this camera, you can use CameraFTP VSS software on a PC.

Step 4. Configure FTP Storage

Click Advanced --> Storage --> FTP Server, you will see the following screen.

You need to set the following parameters:

Enable snapshot to FTP: Enable

Server address: 66.220.9.45

Port: 21

Username, password and confirm password: The same username and password used on

CameraFTP.com

Directory structure: Save in directory

Directory: With Camera Name

Step 5. Configure Events (Motion Detection and Snapshots)

5.1 Configure Motion Detection

If you ordered a service plan with motion detection enabled, then you must configure motion detection

with your camera. Click the "Events" tab and select Motion Detection as shown below:

Enable Motion Detection: Enable

Draw a motion area in Area Settings; set a sensitivity level based on your need;

Upload to FTP: Check the checkbox.

5.2 Configure Image Snapshot Settings

This camera can only upload image snapshots and not video clips. If you ordered a video plan, you need

to order a new image plan and cancel the old video plan. Please note CameraFTP has viewer apps that

can play the recorded image snapshots just like video clips.

The snapshot image resolution is set in the Video section (Video resolution).

If you ordered a continuous image recording plan, you need to click Events --> Snapshot. See the screen

below:

In the CONTINUOUS section:

Enable: Check the checkbox

Format: JPEG

Resolution: 1280x720 (based on your CameraFTP service level)

Quality: Medium

Interval: 1 second (based on your subscription level)

If you ordered a motion-detection plan, you must configure the camera with motion detection:

In the EVENT-TRIGGERED section, please set:

Enable: Check the checkbox

Format: JPEG

Resolution: 1280x720 (based on your CameraFTP service level)

Quality: Medium

Interval: 1000ms (based on your subscription level). If you ordered 1

image/2s, then enter 2000ms.

Click Save to save the settings.

6. CameraFTP Viewer

You are all done. For safety, you can reboot the camera to make sure it still works fine. If you

need to make changes, you can run the setup program again to find the camera’s IP address (as it

may change with DHCP), and then access the camera’s Advanced Configuration pages.

After your camera is setup, you can visit www.cameraftp.com to live monitor or play back your

recorded footage from anywhere. You can also download CameraFTP Viewer App for iOS,

Android and Windows Phone.

Andere Handbücher für TV-IP310PI

Inhaltsverzeichnis

Andere TRENDnet Sicherheitskamera Handbücher

TRENDnet

TRENDnet TV-IP862IC Bedienungsanleitung

TRENDnet

TRENDnet TV-IP344PI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP100-N Bedienungsanleitung

TRENDnet

TRENDnet TV-IP312PI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP200 Bedienungsanleitung

TRENDnet

TRENDnet TV-IP602WN Bedienungsanleitung

TRENDnet

TRENDnet TV-IP201P Bedienungsanleitung

TRENDnet

TRENDnet TV-IP201 Bedienungsanleitung

TRENDnet

TRENDnet EL-HS800 Bedienungsanleitung

TRENDnet

TRENDnet TV-IP252P - SecurView PoE Dome Internet Camera... Bedienungsanleitung

TRENDnet

TRENDnet TV-IP314PI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP301W Bedienungsanleitung

TRENDnet

TRENDnet TV-IP551WI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP743SIC Bedienungsanleitung

TRENDnet

TRENDnet TV-IP862IC Bedienungsanleitung

TRENDnet

TRENDnet TV-IP410PI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP121W Bedienungsanleitung

TRENDnet

TRENDnet TV-IP410WN Bedienungsanleitung

TRENDnet

TRENDnet TV-IP302PI Bedienungsanleitung

TRENDnet

TRENDnet TV-IP343PI Bedienungsanleitung

TRENDnet

TRENDnet 15-AH28B Bedienungsanleitung

TRENDnet

TRENDnet TV-IP400 Bedienungsanleitung

TRENDnet

TRENDnet TV-IP522P Bedienungsanleitung

TRENDnet

TRENDnet TV-IP551W Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung