TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Bedienungsanleitung
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-S2600i
Version 04.06.2005
Stackable SNMP Switch
Quick Installation Guide
Switch SNMP empilable
Guide d'installation rapide
Stapelbarer SNMP-Switch
Kurzanleitung zur Installation
Guía de instalación rápida
del conmutador SNMP apilable
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
4
9
12
1. Prepare for Installation ......................................................................
2. Product Detail ....................................................................................
3. Hardware Installation .........................................................................
4. Configuring TCP/IP Settings ..............................................................
5. Configuring the TEG-S2600i .............................................................
Thank you for purchasing the TRENDnet TEG-S2600i Stackable SNMP
Switch.
This guide will help you setup your Stackable SNMP Switch. Following the
installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section. If you need further technical
support, please visit www.TRENDNET.com or call technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
Minimum System Requirements
Before setting up the TEG-S2600i, you should have the following:
1. Workstations with network cards
2. TCP/IP protocol installed in all workstations
3. A web browser such as Internet Explorer or Netscape Navigator
4. RJ-45 Network Patch Cable to connect your workstations to the TEG-S2600i
TEG-S2600i
One AC power cord
One RS-232 cable
Quick Installation Guide
Four rubber cushions
with adhesive backing
User's Guide CD-ROM
Mounting Kit: 2 mounting
brackets and screws
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-S2600i
Version 04.06.2005
Stackable SNMP Switch
Quick Installation Guide
Switch SNMP empilable
Guide d'installation rapide
Stapelbarer SNMP-Switch
Kurzanleitung zur Installation
Guía de instalación rápida
del conmutador SNMP apilable
2
2. Product Detail
The TEG-S2600i has four LEDs that indicate power, switch status, network
activity, and network speed.
English
RS-232 port
Pair 1 Pair 2
10/100 Mbps
Auto-MDIX
RJ45 Ports
1000 Mbps
Mini-GBIC Slots
10/100/1000 Mbps
Auto-MDIX RJ45 Ports
Caution: For each pair, only one RJ45 or one Mini-GBIC slot can be
used at a time.
3
3. Hardware Installation
English
Please keep in mind that the site where you install the TEG-S2600i may greatly
affect its performance. Refer to the User's Guide in the provided CD-ROM for
optimal installation.
1. Make sure that the power button is in the OFF position.
2. Connect the AC Power cord to the back of the TEG-S2600i.
3. Press the power button to turn on the TEG-S2600i.
4. Use a standard CAT 5 cable to connect your workstations to any of the ports
on the TEG-S2600i.
5. Verify that the PWR and DIAG LEDs display a solid green light. None of
these LEDs should be blinking.
a
e
b
d
4English
Before the TEG-S2600i can be accessed and configured, the computer's
TCP/IP settings need to be changed.
1. Find the Start button located on your Desktop.
2. Click Start, highlight Settings and then click on Control Panel.
3. Double-Click the Network Icon and the Network Properties box will appear.
4. Under the Configuration tab, locate and click TCP/IP with the
corresponding network card. Then click on the Properties button and the
TCP/IP Properties window will appear.
4. Configuring TCP/IP Settings
Windows 95/98/98SE/ME
5English
5. Under the IP Address tab, click on Specify an IP address and enter
192.168.223.10 for IP address and 255.255.255.0 for Subnet Mask. Click
OK.
6. Click OK.
6English
7. At this point, the installation may require files from your Windows CD-ROM.
If you are prompted for the location of these files, insert your Windows
CD-ROM into your CD-ROM drive and select CD-ROM drive.
8. After the files load, the System Settings Change message appears, click
Yes to reboot your system.
9. Your computer is now ready to access and configure the TEG-S2600i.
Note: If this message does not appear, restart your computer manually.
1. Click Start, and click on Control Panel. For Windows 2000, click Start,
highlight Settings, and click Control Panel.
2. Double-Click the Network Connection Icon.
3. Right-Click on the Local Area Connection icon and then click on
Properties. The Local Area Connection Properties box will appear
Windows 2000/XP
7English
4. Under the General tab, locate and click Internet Protocol TCP/IP and then
click Properties. The Internet Protocol (TCP/IP) Properties box will appear.
5. Click on Use the following IP address. Enter 192.168.223.10 for IP
address and 255.255.255.0 for Subnet, and click OK.
8English
6. Click OK.
7. Your computer is ready to access and configure the TEG-S2600i.
Andere Handbücher für TEG-S2600I - 10/100Mbps Switch With Mini-GBIC...
3
Andere TRENDnet Schalten Handbücher
TRENDnet
TRENDnet TK-804R Bedienungsanleitung
TRENDnet
TRENDnet TU2-400E Bedienungsanleitung
TRENDnet
TRENDnet TEG-30102WS Bedienungsanleitung
TRENDnet
TRENDnet TEG-40080ES Bedienungsanleitung
TRENDnet
TRENDnet TPE-30284 Bedienungsanleitung
TRENDnet
TRENDnet TK-209i Bedienungsanleitung
TRENDnet
TRENDnet TEG-S80Dg Bedienungsanleitung
TRENDnet
TRENDnet TK-1603R Bedienungsanleitung
TRENDnet
TRENDnet TE100-S16Eg Bedienungsanleitung
TRENDnet
TRENDnet TEG-240WS Bedienungsanleitung
TRENDnet
TRENDnet TK-403KR Bedienungsanleitung
TRENDnet
TRENDnet TI-RG262i Bedienungsanleitung
TRENDnet
TRENDnet TEG-S2500i Bedienungsanleitung
TRENDnet
TRENDnet TK-200K Bedienungsanleitung
TRENDnet
TRENDnet TK-205K - PS/2 KVM Switch Bedienungsanleitung
TRENDnet
TRENDnet TPE-80WS - Web Smart PoE Switch Bedienungsanleitung
TRENDnet
TRENDnet TU2-NU4 Bedienungsanleitung
TRENDnet
TRENDnet TK-204UK - DVI USB KVM Switch Bedienungsanleitung
TRENDnet
TRENDnet TEG-S40SX Bedienungsanleitung
TRENDnet
TRENDnet TEG-S5g - Gigabit GREENnet Switch Bedienungsanleitung
