TRENDnet TEG-S2620is Bedienungsanleitung
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The availability of some specific channels and/or operational frequency
bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by
the end user.
ii
European Union Notice:
Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC),
the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by
the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
zEN 60950 Product Safety
zEN 300 328 Technical requirement for radio equipment
zEN 301 489-1/-17 General EMC requirements for radio equipment
Trademark recognition
All product names used in this manual are the properties of their respective owners and are
acknowledged.
iii
Contents
1. INTRODUCTION 1
Features................................................................................................................ 2
Package Contents................................................................................................. 2
Ethernet Switching Technology ............................................................................3
2. HARDWARE DESCRIPTION 5
Physical Dimension............................................................................................... 5
Front Panel ........................................................................................................... 5
LED Indicators ...................................................................................................... 6
Rear Panel............................................................................................................7
Desktop Installation............................................................................................... 7
Rack-mounted Installation .................................................................................... 8
3. NETWORK APPLICATION 11
4. CONSOLE MANAGEMENT 14
Login in the Console Interface ............................................................................ 14
Main Menu .......................................................................................................... 15
Function Description ........................................................................................... 17
Status and Counters 17
Port Status 17
Port Counters 18
System Information 19
Switch Static Configuration 21
Administration Configuration 21
Port Configuration 25
Trunk Configuration 26
Port Mirroring Configuration 27
VLAN Configuration 29
Priority Configuration 35
MAC Address Configuration 36
Misc Configuration 39
Protocol Related Configuration 42
iv
STP 42
SNMP 45
LACP 50
IGMP/GVRP 54
802.1x Configuration 55
System Reset Configuration 59
Factory Default 59
System Reboot 60
TFTP Configuration 60
X-modem Upgrade 64
5. WEB-BASED MANAGEMENT 66
About Web-based Management ......................................................................... 66
Preparing for Web Management......................................................................... 66
Online Help ......................................................................................................... 67
System Login ...................................................................................................... 67
Port status........................................................................................................... 67
View the Port Information 69
Port Statistics...................................................................................................... 69
Administrator....................................................................................................... 70
IP Address 71
Switch Setting 72
Basic Switch Settings 72
Advanced Setting 73
Misc Config 74
Console Port Information 78
Port Controls 78
Trunking 80
Aggregator setting 80
Aggregator Information 81
State Activity 82
Forwarding and Filtering 84
IGMP Snooping 84
v
vi
Static MAC Address 85
MAC filtering 86
VLAN configuration 87
Port-based VLAN 88
802.1Q VLAN 90
Spanning Tree 94
System Configuration 95
Per Port Configuration 95
Port Mirroring 96
SNMP Management 97
Security Manager 99
802.1X 100
System Configuration 100
Per port Configuration 101
Misc Configuration 102
TFTP Update Firmware .................................................................................... 102
Configuration Backup........................................................................................ 103
TFTP Restore Configuration 103
TFTP Backup Configuration 104
Factory Default ................................................................................................. 104
System Reboot ................................................................................................. 105
Panel List .......................................................................................................... 105
IP Stacking........................................................................................................ 106
6. TROUBLESHOOTING 109
7. TECHNICAL SPECIFICATION 111
APPENDIX 113
Console Port Pin Assignments ......................................................................... 113
Cables............................................................................................................... 114
100BASE-TX/10BASE-T Pin Assignments ....................................................... 114
LIMITED WARRANTY 116
1. Introduction
Welcome to the World of Network Switching. In the modern business society,
communication and information sharing are fundamental to our life. And computer
networks have proven to be one of the fastest ways of communication.
TEG-S2620is is a multi-port Switch that can be used to build high-performance
switched workgroup networks. This switch is a store-and-forward device that
offers low latency for high-speed networking. The Switch is targeted at workgroup,
department or backbone computing environment.
Figure 1-1. TEG-S2620is
TEG-S2620is features a “store-and-forward “switching scheme. This allows the
switch to auto-learn and store source address in an 8K-entry MAC address table.
MDI (Medium Dependent Interface) Port is also called an "uplink port". The MDI
port does not cross the transmit and receive lines, which is done by the regular
ports (MDI-X ports) that connect to end stations. In general, MDI means
connecting to another Hub or Switch while MDIX means connecting to a
workstation or PC. Therefore, Auto MDI/MDIX means that you can connect to
another Switch or workstation without changing non-crossover or crossover
cabling.
TEG-S2620is has 24 auto-sensing 10/100Base-TX RJ-45 ports and 2 auto detect
Gigabit ports for higher connection speed.
1
Features
Confirms to IEEE802.3 10BASE-T, 802.3u 100BASE-TX, 802.3ab
1000BASE-T, 802.3z Gigabit fiber
24 10/100 TX plus 2 Gigabit copper/Mini GBIC slot stackable intelligent
switch
High back-plane bandwidth 8.8Gbps
8K-entry MAC address table
Management via single IP address
IGMP support for Multi Media application
Port mirror supported
Support Port bandwidth control
Supports GVRP function
DHCP client supported
Support Port Based VLAN /802 .1Q VLAN
IEEE802.3x Flow control
¾Flow control for full duplex
¾Backpressure for half duplex
Support IEEE802.3ad Port trunk with LACP
Broadcast storm filter supported
Support IEEE 802.1p class of service
Support Port security
IEEE 802.1d Spanning tree protocol supported
Auto detect Gigabit copper and MINI GBIC
Support IEEE 802.1x user authentication
Package Contents
Unpack the contents of the TEG-S2620is and verify them against the
checklist below.
TEG-S2620is
2
Power Cord
Four Rubber Feet
RS-232 cable
Rack-mounted Kit
User Guide (CD-ROM)
24TX TEG-S2620is Four Rubber Feet RS-232 cable
Rack-mountedKit PowerCord UserGuide(CD-ROM)
Figure 1-2. Package Contents
Compare the contents of your TEG-S2620is package with the standard checklist
above. If any item is missing or damaged, please contact your local dealer for
service.
Ethernet Switching Technology
Ethernet Switching Technology dramatically boosted the total bandwidth of a
network, eliminated congestion problems inherent with CSMA/CD (Carrier Sense
multiple access with Collision Detection) protocol, and greatly reduced
unnecessary transmissions.
This revolutionized networking. First, by allowing two-way, simultaneous
transmissions over the same port (Full-duplex), which essentially doubled the
bandwidth. Second, by reducing the collision domain to a single switch-port,
which eliminated the need for carrier sensing. Third, by using the
store-and-forward technology’s approach of inspecting each packet to intercept
3
corrupt or redundant data, switching eliminated unnecessary transmission that
slow the network. By employing address learning, which replaced the inefficient
receiving port.
Auto-negotiation regulates the speed and duplex of each port, based on the
capability of both devices. Flow-control allows transmission from a 100Mbps node
to a 10Mbps node without loss of data. Auto-negotiation and flow-control may
require disablement for some networking operations involves legacy equipment.
Disabling the auto-negotiation is accomplished by fixing the speed or duplex of a
port.
Ethernet Switching Technology supplied higher performance at costs lower than
other solutions. Wider bandwidth, no congestion, and the reduction in traffic is
why switching is replacing expensive routers and inefficient hubs as the ultimate
networking solution. Switching brought a whole new way of thinking to networking.
4
Andere Handbücher für TEG-S2620is
2
Inhaltsverzeichnis
Andere TRENDnet Schalten Handbücher
TRENDnet
TRENDnet TPE-S44 - Switch Bedienungsanleitung
TRENDnet
TRENDnet TK-205i Bedienungsanleitung
TRENDnet
TRENDnet TL2-E284 Bedienungsanleitung
TRENDnet
TRENDnet TEG-448WS - Switch Bedienungsanleitung
TRENDnet
TRENDnet NWay Bedienungsanleitung
TRENDnet
TRENDnet TK-IP101 Bedienungsanleitung
TRENDnet
TRENDnet TPE-3012L Bedienungsanleitung
TRENDnet
TRENDnet TPE-224WS - Web Smart PoE Switch Bedienungsanleitung
TRENDnet
TRENDnet TU-400E Bedienungsanleitung
TRENDnet
TRENDnet TPE-TG240g Bedienungsanleitung
TRENDnet
TRENDnet TEG-S224 - DATA SHEETS Bedienungsanleitung
TRENDnet
TRENDnet TEG-S5g - Gigabit GREENnet Switch Bedienungsanleitung
TRENDnet
TRENDnet TK-423K - USB/PS/2 KVM Switch Bedienungsanleitung
TRENDnet
TRENDnet TE100-S55E Bedienungsanleitung
TRENDnet
TRENDnet TEG-424WS Bedienungsanleitung
TRENDnet
TRENDnet TEG-S240TX - DATA SHEETS Bedienungsanleitung
TRENDnet
TRENDnet TK-204UK - DVI USB KVM Switch Bedienungsanleitung
TRENDnet
TRENDnet TE100-DX4PCI Bedienungsanleitung
TRENDnet
TRENDnet TE100-DX8 - Bedienungsanleitung
TRENDnet
TRENDnet TK-206i Bedienungsanleitung
