Tripp Lite AG-04F5 Series Bedienungsanleitung
1
UPS Systems
Models:
OMNIVSX850A, OMNIVSX1000A, OMNIVSX1500A
(Series Numbers: AG-04F5, AG-04F1, AG-04F2)
Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2020 Tripp Lite. All rights reserved.
2
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the
installation, operation and storage of this product. Failure to heed these warnings may
affect the warranty.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or
direct sunlight.
• Operating Temperature: 0°C to 40°C
• Storage Temperature: -15°C to 45°C
• Humidity: 0% to 90% R.H.
• Operating Altitude: 0 m to 2,000 m
• Storage Altitude: 0 m to 3,000 m
• Pollution: PD2
• Overvoltage Category: II for normal mode, I for stored energy mode
• Leave adequate space around all sides of the UPS for proper ventilation.
• Only set the UPS upright on a sturdy flat surface. Do not block fans or ventilation holes, as this will
seriously inhibit the unit's internal cooling and cause product damage not covered under warranty.
UPS Connection Warnings
• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the UPS into itself;
this will damage the UPS.
• Do not modify the UPS plug, and do not use an adapter that would eliminate the UPS ground
connection.
• Do not use extension cords to connect the UPS to an AC outlet.
• If the UPS receives power from a motor-powered AC generator, the generator must provide clean,
filtered, computer-grade output.
• The mains socket outlet that supplies the UPS should be easily accessible and located near the UPS.
• For use on a TN power distribution system of input power supply. The UPS stored energy output
device provides a TN power system.
Important Safety Instructions
3
Important Safety Instructions
Equipment Connection Warnings
Short Circuit backup protection and overcurrent protection is provided by the
building installation.
To reduce the risk of fire, connect only to a circuit provided branch circuit
overcurrent protection. The plug on the power supply cord is intended to serve
as the disconnect device. Be sure the socket-outlet is installed near the
equipment and is made easily accessible.
• Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended.
• Do not connect surge protectors or extension cords to the output of your UPS. This might damage
the UPS and may affect the surge protector and UPS warranties.
• Connect the UPS to an outlet that is adequately protected against excess currents, short circuits
and earth faults as part of the building installation.
Model Number
Agency
Series
Number
Dimensions
(H x W x D) Weight
AC Fuse/
Breaker
Output
Short-
Circuit
Current
OMNIVSX850A AG-04F5 160 x 122 x 345 mm 6 kg Fuse: T5AL,
250VAC
Approx. 64A
Peak
OMNIVSX1000A AG-04F1 160 x 122 x 345 mm 6.5 kg Fuse: T10AL,
250VAC
Approx. 64A
Peak
OMNIVSX1500A AG-04F2 182 x 130 x 320 mm 10 kg Fuse: T10AL,
250VAC
Approx.
75.8A Peak
4
Important Safety Instructions
Battery Warnings
• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe
proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.
Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before
performing battery replacement. Use tools with insulated handles. There are no user-serviceable
parts inside the UPS. Battery replacement should be performed only by authorised service
personnel using the same number and type of batteries (Sealed Lead-Acid).
The batteries are recyclable. Refer to your local codes for disposal requirements or visit
tripplite.com/support/recycling-program for recycling information. Tripp Lite offers a complete
line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at
tripplite.com/products/battery-finder/ to locate the specific replacement battery for your UPS.
CAUTION: A battery can present a risk of electrical shock and high short-circuit
current. Contact with any part of a grounded battery can result in electrical shock.
The following precautions should be observed when working on batteries:
• Remove watches, rings or other metal objects.
• Use tools with insulated handles.
• Wear rubber gloves and boots.
• Do not lay tools or metal parts on top of batteries.
• Disconnect the charging source and load prior to installing or maintaining the battery.
• Remove battery grounds during installation and maintenance to reduce likelihood of
shock.
• Remove the connection from ground if any part of the battery is determined to be
grounded.
• Unplug the UPS from the AC mains receptacle. Disconnect all cables, including the
equipment plugged into the UPS.
• Servicing of batteries should be performed or supervised by personnel knowledgeable
about batteries and required precautions.
• When replacing batteries, replace with the same type and number of batteries or battery
packs.
• CAUTION: Do not dispose of batteries in a fire. The batteries may explode.
• CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin
and eyes. It may be toxic.
UPS and Battery Recycling
Tripp Lite products use sealed lead-acid batteries, which are highly recyclable.
Call Tripp Lite at 1.773.869.1234 or visit tripplite.com/support/recycling-program for more
information on recycling the batteries or any other Tripp Lite product. Please refer to local
codes for disposal requirements.
5
STEP 1: Plug the UPS into a properly grounded outlet.
After plugging the UPS into a wall outlet, press and hold the power button until a beep is heard, then
release to turn on the UPS.
Note: The UPS will not turn on automatically in the presence of live utility power.
Quick Installation
OMNIVSX850A / OMNIVSX1000A / OMNIVSX1500A
STEP 2: Plug your equipment into the UPS.
Outlets marked BATTERY & SURGE offer UPS battery backup support during power failures. Connect
your vital computer equipment into these outlets.
Your UPS is designed to support electronic equipment only. You will overload the UPS if the total
volt-amp (VA) ratings for all the equipment connected to the BATTERY/SURGE PROTECTED outlets
exceed the UPS output capacity. To find your equipment’s VA ratings, look on their nameplates. If the
equipment is listed in amps (A), multiply the number of amps by 230 to determine VA. For example:
1A × 230 = 230VA. If you suspect you have overloaded the outlets, check Load Meter screens (see
Display UPS/Power Conditions in Basic Operation).
Use the two included cables
with Australia plugs to connect
equipment to the UPS.
For illustrative purposes only.
User must supply power cord and plug
that is compatible with power outlets used in that region.
Connected
Equipment
Local
Utility
Power
OMNIVSX1500A model shown. Number of outlets
and outlet layout may differ by model.
6
Quick Installation
STEP 3: Turn on the UPS.
After connecting your equipment to the UPS, press and hold the power button until a beep is heard,
then release to turn on your UPS.
If the on-line AC power icon does not illuminate when the UPS is turned ON, try the following:
1. Make sure the UPS is plugged into a live AC outlet.
2. Press the power button to turn on the UPS. A beep should sound when the UPS starts.
3. If the UPS still does not start, contact Tripp Lite Tech Support for assistance.
Basic Operation
UPS ON/OFF
• Plug the UPS into a live, grounded outlet: The entire LCD screen will illuminate for 4 seconds,
then the display will report the output voltage of “0V”. BATTERY/SURGE PROTECTED outlets will be
OFF. The battery charger will engage as necessary.
• Plug equipment into the UPS: You will overload the UPS if the total volt-amp (VA) ratings for
all the equipment connected to the BATTERY/SURGE PROTECTED outlets exceed the UPS output
capacity. To find your equipment’s VA ratings, look on their nameplates. If the equipment is listed
in amps (A), multiply the number of amps by 230 to determine VA. For example: 1A × 230 =
230VA.
• Turn the UPS on: Press and hold the power button until the alarm sounds, then release. The
UPS alarm will beep for 2 seconds. The BATTERY/SURGE PROTECTED outlets will begin passing
AC line power. The UPS will automatically recharge internal batteries as needed. Once turned on,
your UPS is ready to protect connected equipment from blackouts, brownouts, overvoltages and
transient surges.
• Turn the UPS off: Press the power button.
Note: UPS system will function properly upon initial startup. However, maximum runtime for the unit’s
battery will only be accessible after it has been charged for 24 hours.
7
Basic Operation
Display UPS/Power Conditions
On-Line AC Power Mode LCD Data
The LCD touchscreen offers five screens of UPS and site power information when the UPS is
operating in line-power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %, Battery Charge
Level) are available for viewing in line-power mode. Press the front panel LCD to advance to the next
screen. Screen 5 (Overload) is displayed automatically only when the UPS is loaded to levels greater
than 110%.
The LCD screen reports that AVR (Auto Voltage Regulation) buck/boost circuits are active any time
the line power icon is flashing.
1Output Voltage 2Input Voltage 3Load %
Note: The LCD touchscreen automatically turns off in line-power mode 20 seconds after it was last touched. To
re-activate the LCD for an additional 20 seconds, touch the screen.
Operating Mode Alarm Description
Battery Mode Normal No Alarm
Battery Low Sounds Every Second
Over Load Sounds Every 0.5 Second
Line Mode Normal No Alarm
Over Load Sounds Every 0.5 Second
Battery Replace Sounds Every Minute
Fault Mode Sounds Continuously
4Battery Charge Level 5Overload
8
Basic Operation
Battery Power Mode LCD Data
The LCD touchscreen offers five screens of UPS and site power information when the UPS is
operating in line-power mode. Screens 1-4 (Output Voltage, Input Voltage, Load %, Battery Charge
Level) are available for viewing in line-power mode. Press the front panel LCD to advance to the next
screen. Screen 5 (Overload) is displayed automatically only when the UPS is loaded to levels greater
than 110%.
Critical Fault Screens
Error Code Critical Fault Solution
F01 OUTPUT SHORT Disconnect load(s) from UPS outlets. Power off UPS and
contact Tripp Lite Technical Support for assistance.
F02 OVER LOAD Remove excess load, check load meter on LCD for load status.
F03 OVER CHARGE Turn unit off, unplug UPS and contact Tripp Lite Technical
Support for assistance.
F04 BATTERY LOW
VOLTAGE
Charge UPS for 24 hours. If problem persists, replace battery
and contact Tripp Lite Technical Support if problem persists.
F05 BATTERY MODE
HIGH OUTPUT
Turn off power to the UPS and contact Tripp Lite Technical
Support for assistance.
1Output Voltage 2Input Voltage 3Load %
4Battery Charge Level 5Overload
Note: The touchscreen LCD will remain ON continuously during battery mode operation.
9
IN OUT
Features
Front Panel
Rear Panel
1
2
4
5
3
7
6
OMNIVSX1500A model shown. Number of outlets
and outlet layout may differ by model.
1ON/OFF Button: When the UPS is OFF, press and hold the ON/OFF button until a beep is heard
to turn the UPS ON. When the UPS is ON, press and hold the ON/OFF button to turn the UPS
OFF.
2LCD Touchscreen Panel: Provide current status of the UPS. For a detailed description, refer to
“Display UPS/Power Conditions” in the Basic Operation section.
3Battery Backup/Surge Protected Outlets: These outlets offer battery backup support and
premium surge suppression for critical devices requiring battery backup support.
4USB Communication Port: This port can connect your UPS to any computer for automatic
saves and unattended shutdown in the event of a power failure. Use with Tripp Lite’s
PowerAlert®Software (available as a FREE download at tripplite.com) and the USB cable
included with your UPS. This connection is optional; your UPS will work properly without this
connection.
Note: This UPS System provides basic communication compatibility with most integrated Windows®,
Macintosh®and Linux®power management applications.
10
Features
Battery Replacement
Under normal conditions, the original battery in your UPS will last several years. Battery replacement
should only be performed by qualified personnel. Refer to “Battery Warnings” in the Important
Safety Instructions section for more information.
Models OMNIVSX850A and OMNIVSX1000A require one 12V DC, 9Ah replacement battery.
Model OMNIVSX1500A requires two 12V DC, 9Ah replacement batteries.
For further information about replacement compatibility and ordering, visit
tripplite.com/products/battery-finder.
Battery replacement must be done using the same battery type and
quantity: 12V DC sealed lead-acid, 6-cell and in compliance with UL 1989.
CAUTION: Risk of energy hazard. Before replacing batteries, remove conductive
jewelry such as chains, wristwatches and rings. High energy passing through
conductive materials may cause severe burns.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to instructions.
5AC Power Input: Use the Australian power cord to connect the OMNIVSX850A /
OMNIVSX1000A / OMNIVSX1500A to the main power source.
6Replaceable Input Fuse: Protects your electrical circuit from overcurrent draw from the UPS
load. If the fuse has blown, remove some of the load, then replace the fuse. The fuse is rated
for 5A/250V AC for OMNIVSX850A and 10A/250V AC for OMNIVSX1000A / OMNIVSX1500A.
7Variable-Speed Cooling Fan (OMNIVSX1500A only): This fan regulates the internal
temperature of the UPS.
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Tripp Lite UPS Handbücher
Tripp Lite
Tripp Lite SmartPro SMART500RT1U Bedienungsanleitung
Tripp Lite
Tripp Lite OMNISMART350HG Bedienungsanleitung
Tripp Lite
Tripp Lite BCPERS450 Bedienungsanleitung
Tripp Lite
Tripp Lite OmniSmart OMNI300NAFTA Bedienungsanleitung
Tripp Lite
Tripp Lite SmartOnline SU1500RTXL2U Bedienungsanleitung
Tripp Lite
Tripp Lite SMART5000TEL3U Bedienungsanleitung
Tripp Lite
Tripp Lite OmniSmart OMNIVS800 Bedienungsanleitung
Tripp Lite
Tripp Lite Line-Interactive UPS System SMART750USB Bedienungsanleitung
Tripp Lite
Tripp Lite SmartPro SMART750RMXL2U Bedienungsanleitung
Tripp Lite
Tripp Lite SMART1524ET Bedienungsanleitung
Tripp Lite
Tripp Lite Audio/Video On-Line UPS System Bedienungsanleitung
Tripp Lite
Tripp Lite OMNIVS1500 Bedienungsanleitung
Tripp Lite
Tripp Lite SmartOnline SU80KX2 Installationsanleitung
Tripp Lite
Tripp Lite SmartOnline Bedienungsanleitung
Tripp Lite
Tripp Lite SmartOnline SU16KRT-1TF Bedienungsanleitung
Tripp Lite
Tripp Lite SmartPro SLT Bedienungsanleitung
Tripp Lite
Tripp Lite BC600SINE Bedienungsanleitung
Tripp Lite
Tripp Lite SmartOnline 3-Phase 10kVA Bedienungsanleitung
Tripp Lite
Tripp Lite OmniSmart 725 Bedienungsanleitung
Tripp Lite
Tripp Lite BC350 Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
