TriStar AC-5564CH Bedienungsanleitung

AC-5564CH

EN | Instruction manual

IT | Manuele utente

FR | Mode d’emploi

DE | Bedienungsanleitung

Air conditioner

SAFETY INSTRUCTIONS

• Please read this user’s manual carefully to ensure

proper use, maintenance and installation.

• The appliance is for indoor use only.

• Do not use the unit on a socket under repairs or not

installed properly

• Do not use the unit, follow these precautions:

o Near to source of re.

o An area where oil is likely to splash.

o An area exposed to direct sunlight.

o An area where water is likely to splash.

o Near a bath, a laundry, a shower or a swimming pool.

• Never insert your ngers, rods into the air outlet.

Take special care to warn children of these dangers.

• Keep the unit upward while transport and storage,

for the compressor locates properly.

• Before cleaning the air-conditioner, always turn o

or disconnect the power supply.

•When moving the air-conditioner, always turn o and

disconnect the power supply, and move it slowly.

• To avoid the possibility of re disaster, the air-

conditioner shall not be covered.

• All the air-conditioner sockets must comply with

the local electric safety requirements. If necessary,

please check it for the requirements.

• Children should be supervised to ensure that they

do not play with the appliance.

• If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualied persons in order to avoid a hazard.

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

• The appliance shall be installed in accordance with

national wiring regulations.

• Notes:

o If any parts damage, please contact the dealer or

a designated repair shop;

o In case of any damage, please turn o the air

switch, disconnect the power supply, and contact

the dealer or a designated repair shop.

o In any case, the power cord shall be rmly grounded.

• To avoid the possibility of danger, if power cord

is damaged, please turn o the air switch and

disconnect the power supply. It must be replaced

from the dealer or a designated repair shop.

WARNING

• Do not use means to accelerate the defrosting

process or to clean, other than those recommended

by the manufacturer.

• The appliance shall be stored in a room without

continuously operating ignition sources (for

Instruction manual

example: open ames, an operating gas appliance

or an operating electric heater).

• Do not pierce or burn.

• Be aware that refrigerants may not contain an odor.

• Appliance shall be installed, operated and stored

in a room with a oor area larger than X m2. (X=12

for 9000Btu/h,10500Btu/h; X=15 for 12000Btu/

h,140000Btu/h)

• Contact authorized service technician for repair or

maintenance of this unit.

• Do not pull , deform or modify the power supply

cord, or immerse it in water. Pulling or misuse of the

power supply cord can result in damage to the unit

and cause electrical shock.

• Compliance with national gas regulations shall be

observed.

• Keep ventilation openings clear of obstruction.

• Any person who is involved with working on

or breaking into a refrigerant circuit should

hold a current valid certicate from an industry

accredited assessment authority, which authorizes

their competence to handle refrigerants safely

in accordance with an industry recognized

assessment specication.

• Servicing shall only be performed as recommended

by the equipment manufacturer. Maintenance

and repair requiring the assistance of other

skilled personnel shall be carried out under the

supervision of the person competent in the use of

ammable refrigerants.

• Do not operate or stop the unit by inserting or

pulling out the power plug, it may cause electric

shock or re due to heat generation.

• Unplug the unit if strange sounds, smell, or smoke

comes from it.

CAUTION

• Please make sure the product ventilates all the

time, make sure the inlet and outlet ventilation are

not blocked in any way.

• Operate this unit on a horizontal surface to avoid

water leakage.

• Do not operate this unit in an explosive or corrosive

atmosphere.

• Operate this unit in an ambient of 35 degree

centigrade or less.

• The heating function of the unit should be

operated in an indoor ambient temperature

between 15oC and 25oC, the cooling function of

the unit should be operated in an indoor ambient

temperature between 18oC and 35oC.

• Clean air lter periodically to enjoy the most

ecient cooling.

• When the unit is shut o, please wait at least 3.5

minutes before restarting. This to prevent the

compressor from being damaged.

• This unit needs at least 7 Amps of electricity to have

its compressor operational.

• To avoid the household electricity block out, please

do not use any extension cord for this unit.

• This unit is for indoor cooling, heating and

dehumidifying.

• In order to dispose the appliance safely, please

remove the batteries from the unit before

scrapping it.

WARNING

Specic information regarding appliances with R 290

refrigerant gas.

• Thoroughly read all of the warnings.

• When defrosting and cleaning the appliance , do

not use any tools other than those recommended

by the manufacturing company.

• The appliance must be placed in an area without

any continuously sources of ignition (for example:

open ames , gas or electrical appliances in

operation).

• Do not puncture and do not burn.

• Appliance shall be installed, operated and stored

in a room with a oor area larger than X m2. (X=12

for 9000Btu/h,10500Btu/h; X=15 for 12000Btu/

h,140000Btu/h)

• This appliance contains Y g (see rating label back of

unit ) of R290 refrigerant gas.

• R290 is a refrigerant gas that complies with the

European directives on the environment. Do not

puncture any part of the refrigerant circuit.

• If the appliance is installed, operated or stored in

a non ventilated area, the room must be designed

to prevent to the accumulation of refrigerant leaks

resulting in a risk of re or explosion due to ignition

of the refrigerant caused by electric heaters, stoves,

or other sources of ignition.

• The appliance must be stored in such a way as to

prevent mechanical failure.

•Individuals who operate or work on the refrigerant

circuit must have the appropriate certication issued by

an accredited organization that ensures competence in

handling refrigerants according to a specic evaluation

recognized by associations in the industry.

• Repairs must be performed based on the

recommendation from the manufacturing

company. Maintenance and repairs that require

the assistance of other qualied personnel must be

performed under the supervision of an individual

specied in the use of ammable refrigerants.

REFRIGERANT

(CE) N 842/2006: This air conditioner contains the refrigerant R290. The

amount of refrigerant is less than 1kg, and is in a closed cooling circuit.

The coolant does have zero ozone depletion potential, but is a so-called

greenhouse gases under the Kyoto Protocol and may thus contribute to

global warming, if it is released to the atmosphere. Therefore only trained

technicians with refrigerant certicate make a lling or emptying. Your air

conditioner does not have be relled with refrigerant if used properly and

has an undamaged coolant circuit. GWP: R290: 3

Air conditioner

PARTS DESCRIPTION

1. Control panel

2. Air outlet

3. Hot air outlet

4. Drain hole

5. Filter

6. Cold inlet

7. Hot air inlet

Accessories

Part Description

Exhaust hose

Hose connector

Window kit

Remote control

Drainage tube

Instruction manual

Function of Control Panel

1. Power on/o button

2. Temperature + button

3. Mode button

4. Timer on/o button

5. Temperature - button

6. Speed

7. Dehumidier indicator

8. Cool mode indicator

9. Heat indicator

10. Connector window

11. Medium fan speed indicator

12. High fan speed indicator

13. Auto indicator

14. Low fan speed indicator

15. Led display

Function of Remote Control

1. Power (on/o button)

2. Mode (mode selector)

3. Timer (program button)

4. Speed (Fan speed selector)

5. Temp+ (Temperature selector up)

6. Temp- (Temperature selector down)

BEFORE THE FIRST USE

• Place the unit in the correct upright position before unpacking.

• Cut the two packing straps.

• Slide the carton in an upwards motion and it will release from the base.

• Grip the carry handles located on either sides of the unit and carefully

lift until it slides out of the foam base.

• Install the exhaust hose on the unit before operating the unit.

• Please ensure the unit is not placed against objects which will obstruct

air intake e.g. furniture or curtains as this will aect it's performance

dramatically.

• Because the machine distributes hot air, please don’t place or operate

in a narrow place.

• Do not place the machine in full sun as it might shut down due to

overheat and the color of the machine may soon fade out.

• Do not place the machine in a humid place.

• For eective heating and cooling functions, please ensure that the

following steps are undertaken:

- Extend the exhaust hose to a length of not more than 400mm. The

exhaust hose must be kept parallel and must not be bent up or down.

- A distance of 500mm minimum must be kept between the lter side

of the unit and wall or any other obstacles.

• Insert the power cord into an grounded AC220~240V/50Hz socket

• This unit can evaporate the condensation and distribute through the

exhaust hose automatically.

Air conditioner

Exhaust hose installation

• The exhaust hose can be removed from the machine by rotating it in

the arrow direction as illustrated by (1) diagram.

• The exhaust hose can be installed at the machine by rotating it in the

arrow direction as illustrated by (2) diagram.

Window kit installation

Install the Exhaust Hose and the Adjustable Window Slider Kit as shown in

gure 1 or gure 1a.

USE

• Power button: Press to turn unit "ON" or "OFF".

• Temp- (down):During cooling function this key lowers the preset

temperature by 1oC each time it is pressed and the minimum limit is

17oC. During heating function this key lowers the preset temperature

by 1oC each time and the minimum limit is 15oC.

• Speed: Press to select either low, medium, or high fan speed. Note: In

dehumidifying function, this key is invalid because the unit is dened

to be low speed in dehumidifying mode.

• Temp+ (up): During cooling function this key raises the preset

temperature by 1oC each time it is pressed and the maximum limit is

30oC. During heating function this key raises the preset temperature by

1oC each time it is pressed and the maximum limit is 25oC.

• Programmable timer: The timer-on is used to turn on the unit

automatically after the set time is over. Press the "timer" button at stand-

by status , then set the time you desired by pressing“temp+”or“temp-“

button. Once the set hour has come to an end, the unit will turn on

automatically. Press the "power" button before time out, the setting time

will be canceled and the unit will turn on. You can set the function and

fan speed while setting the timer. The timer-o is used to turn o the

unit automatically after the setting time is over. Press the“timer” button

at operating status ,then set the time you desired by pressing“temp+”

or“temp-“ button. Once the set hour has come to an end, the unit will

turn o automatically. Press the "power" button before the time out, the

setting time will be canceled and the unit will turn o.

• Mode: Press this key to select cooling, fan, dehumidifying or heating.

Alarm

• When the water tank is full,"E2" will be displayed on the display panel. To

resume operation, please remove the rubber cap of the drain, hose to

drain out the water rstly. The E2 warning will disappear after draining,

and then you can restart the unit by pressing the power button.

LED display

• The display indicates the current setting temperature or the timer

setting. When the set temperature or the timer is adjusted, the new

setting is shown then the display returns the current set temperature.

The display is also used to show error codes should a fault occur.

Air lter function

• If there is a large amount of dust on the net, the air volume will be

reduced.

Instruction manual

• Clean the lter every two weeks.

1. Open Strainer Overlay

2. Take out lter.

3. Soak the strainer in warm water about 40 degrees Celsius and put

some neutral detergent in it, then rinse o the lotion and keep it dry in

a cool place.

4. Installation: Press the reverse step of the disassembly to install the

lter back.

Drainage mode

In general, there is no need to use the drainage tube, because the

evaporator of the machine will automatically evaporate water. If the

ambient humidity is very high, we need to use the drainage tube.

Automatic evaporation and drainage of condensed water

• The machine can automatically evaporate condensing water and drain

out of the exhaust hose.

• In the cooling mode, the machine does not need to connect the drain to

drain water, please ensure that the plug of the machine has been installed.

• In the dehumidication or heating mode, the plug "A" in the drain hole

should be removed.

• The drain plug "A" in the drainage hole should be removed and an

appropriate drainage pipe must be installed for continuous drainage.

CLEANING MAINTENANCE AND STORAGE

• Before cleaning, be sure to disconnect the unit from any electric supply

outlet.

• First clean the surface with a neutral detergent and wet cloth, and then

wipe it with a dry cloth.

• Do not use gasoline or other chemicals to clean the unit.

• Do not wash the unit directly.

• If the conditioner is damaged, please contact the dealer or repair shop.

• If you will not use the machine for a long time, it is better to open the

drain hose at the bottom and drain the unit thoroughly.

• Store the unit in a dry place.

Air conditioner

Problem Possible causes Suggested remedies

E1Electrical short on both temperature

sensor and PCB. Contact an electrician for repair.

Indicates water tank full or

possible incorrect connection of

the plug

User needs to pull out the rubber

stopper which is located at the

side of the unit to drain the water

away. Check that the plug is

properly connected.

Electrical short

The product or equipment contains uorinated greenhouse gas.

Art.nr. AC-5564CH

Coolant: R290

Quantity in kg: 0,235

Global Warming Potential: 3

CO2 Equivalent in tonnes: 0.0007

GUARANTEE

• This product is guaranteed for 24 months granted. Your warranty is

valid if the product is used in accordance to the instructions and for

the purpose for which it was created. In addition, the original purchase

(invoice, sales slip or receipt) is to be submitted with the date of

purchase, the name of the retailer and the item number of the product.

• For the detailed warranty conditions, please refer to our service

website: www.tristar.eu

ENVIRONMENT

This appliance should not be put into the domestic garbage at the

end of its durability, but must be oered at a central point for the

recycling of electric and electronic domestic appliances. This symbol on

the appliance, instruction manual and packaging puts your attention to

this important issue. The materials used in this appliance can be recycled.

By recycling of used domestic appliances you contribute an important

push to the protection of our environment. Ask your local authorities for

information regarding the point of recollection.

SUPPORT

You can nd all available information and spare parts at www.tristar.eu

Instruction manual

Contact an electrician for repair.

Inhaltsverzeichnis

Sprachen:

Andere TriStar Klimaanlage Handbücher

TriStar

TriStar AC-5474 Bedienungsanleitung

TriStar

TriStar AC-5560 Bedienungsanleitung

TriStar

TriStar AC-5560 Bedienungsanleitung

TriStar

TriStar AC 5670 Bedienungsanleitung

TriStar

TriStar AT-5464 Bedienungsanleitung

TriStar

TriStar AC-5413 Bedienungsanleitung

TriStar

TriStar AT-5451 Bedienungsanleitung

TriStar

TriStar AC-5560 Bedienungsanleitung

TriStar

TriStar AC-5491 Bedienungsanleitung

TriStar

TriStar AT-5433 Bedienungsanleitung

TriStar

TriStar AT-5443BS Bedienungsanleitung

TriStar

TriStar AC-5527PR Bedienungsanleitung

TriStar

TriStar PD-8899 Bedienungsanleitung

TriStar

TriStar AC-5495 Bedienungsanleitung

TriStar

TriStar AC-5517 Bedienungsanleitung

TriStar

TriStar AC-5498 Bedienungsanleitung

TriStar

TriStar AC-5521 Bedienungsanleitung

TriStar

TriStar AC-5491 Bedienungsanleitung

TriStar

TriStar AC-5477 Bedienungsanleitung

TriStar

TriStar AC 5490 Bedienungsanleitung

TriStar

TriStar AC-5493 Bedienungsanleitung

TriStar

TriStar AT-5446 Bedienungsanleitung

TriStar

TriStar AT-5445 Bedienungsanleitung

TriStar

TriStar AT-5461 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung