Triumph AL7100F Bedienungsanleitung

For Customer Service Call 1-888-996-2729

1-888-996-2729

FAX: 1-866-873-3535

gameroom@escaladesports.com

We strive to ensure that our products are of the highest quality

and free of manufacturing defects or missing parts. However, if

you have any problems with your new product,

DO NOT RETURN IT TO THE STORE,

please contact us toll free @:

When contacting Escalade Sports please provide your model number, date code (if

applicable), and part number if requesting a replacement part. These numbers are

located on the product, packaging, and in this owners manual.

Your Model Number:

Please have your model number when inquiring about parts.

Date Code:

Purchase Date:

PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

AL7100F

2-AL7100F- -JL

Mailing Address: (Correspondence Only)

Escalade Sports

PO Box 889

Evansville, Indiana 47706-0889

Physical Location:

Escalade Sports

817 Maxwell Ave.

Evansville, Indiana 47711

IMPORTANT! READ EACH STEP

IN THIS MANUAL BEFORE YOU

BEGIN THE ASSEMBLY.

TWO (2) ADULTS ARE REQUIRED TO ASSEMBLE

THIS AMERICAN LEGEND ARCADE BASKETBALL

2 For Customer Service Call 1-888-996-2729

Tools Needed:

Make sure you understand the following tips before you begin to assemble your

basketball shootout.

1.This game (with Mechanical Scoring Arm) can be played outdoors in dry weather

- but must be stored indoors.

2.Tighten hardware as instructed.

3.Do not over tighten hardware,as you could crush the tubing.

4.Some drawings or images in this manual may not look exactly like your product.

5.To prevent damage to the electronics or to your wall, do not place this unit any closer

than six inches from the wall.

T1 Allen Wrench (provided)

Phillips Screwdriver

Plyers

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO

ADULTS ARE REQUIRED TO ASSEMBLE THIS GAME TABLE.

ATTENTION:

H1 - M6 x 35mm

Allen Head Bolt

(1 pc)

H4 - M6 x 15mm

Flat Washer

(3 pcs)

H5 - M6

Wing Nut

(19 pcs)

H6 - Plastic

Bushing

(2 pcs)

H2 - M6 x 90mm

Allen Head Bolt

(2 pcs)

H3 - M6 x 25mm

Allen Head Bolt

(16 pcs)

3 For Customer Service Call 1-888-996-2729

HARDWARE IDENTIFIER

(To Scale)

H7 - M6

Lock Washer

(16 pcs)

(Not to Scale)

T1 - Allen Wrench

(1 pc)

H8 - Plastic

Wing Bolt to

attach P17

Control Box

(1 pc)

4For Customer Service Call 1-888-996-2729

PARTS IDENTIFIER (Not to Scale)

P1 - Left Lower

Tube Assembly

(1 pc)

P2 - Right Lower

Tube Assembly

(1 pc)

P3 - Left Middle

Tube Assembly

(1 pc)

P4 - Right Middle

Tube Assembly

(1 pc)

P5 - Front

Tube Assembly

(1 pc)

P6 - Upper

Tube (2 pcs)

P7 - Backboard

with Tubes Assembly

(1 pc) P8 - Ramp

Chute (1 pc)

5For Customer Service Call 1-888-996-2729

PARTS IDENTIFIER (Not to Scale)

P11 - Mechanical

Scoring Arm

(2 pcs)

P12 - Rim (2 pcs)

P13 - Rim Net

(2 pcs)

P14 - Rim Support

Plate (2 pcs)

P18 - Mechanical Scoring

Arm Support Plate (2 pcs)

ACCESORY IDENTIFIER (Not to Scale)

A1 - Air Pump

with Needle

(1 pc)

A2 - Basketball (4 pcs) A3 - A/C Adapter (1 pc)

P15 - Locking Pin

(2 pcs)

Note: This is a special rim net

designed to avoid entanglement

3 pcs AA Batteries Required ,

Not Supplied

with the mechanical scoring arm.

Note: This is a special rim

designed to avoid entanglement

with the mechanical scoring arm.

P16 - Scoring

Control Box

Wire (1 pc)

P9 - Electronic

Scorer (1 pc)

P10 - Electronic

Scorer Face Plate

(1 pc)

P17 - Control Box

(1 pc)

6For Customer Service Call 1-888-996-2729

STEP 1

PARTS REQUIRED:

1 pc - P1 Left Lower Tubes Assembly

1 pc - P2 Right Lower Tubes Assembly

Connect P2 - Right Lower Tubes Assembly to

P1 - Left Lower Tubes Assembly using Spring

Lock as shown in FIGURE 1.

NOTE: STEP 1, 2 and 3 requires

a second adult to help “hold” the

assemblies as being assembled.

Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List.

NOTE: STEP 1, 2 AND 3 requires a second adult to help “hold” the assemblies as being assembled

NOTE: When unfolding assemblies, be careful not to bend any parts.

Spring Lock

face backside

STEP 2

PARTS REQUIRED:

1 pc - P3 Left Middle Tubes Assembly

1 pc - P4 Right Middle Tubes Assembly

Connect P4 - Right Middle Tubes Assembly to

P3 - Left Middle Tubes Assembly using Spring

Lock as shown in FIGURE 2.

NOTE: The only assembly in this step is

connecting this spring lock.

FIGURE 1 P2

Spring Lock

FIGURE 2

WARNING / PINCH HAZARD!

Keep hands and fingers away from

hinge until STEP 3 is complete and

the hinge is in a controlled position.

Spring Lock

face backside

Spring Lock

face backside

7For Customer Service Call 1-888-996-2729

STEP 3

PARTS REQUIRED:

1 pc - H1 M6 x 35 mm

Allen

Head Bolt

1 pc - H4 Flat Washer

1 pc - H5 Wing Nut

Connect Middle Tubes Assembly from STEP 2 to

Lower Tubes Assembly from STEP 1 using Spring

Locks. Next, using H1 Bolt, H4 Washer and H5 Wing

Nut connect frame braces as shown in FIGURE 3

and DETAIL A.

NOTE: Lastly, these six points can now

be tightened using a phillips screwdriver

or Phillips Allen Wrench (T1) provided

and plyers.

FIGURE 3

Spring Lock

DETAIL A

ASSEMBLY FRAME

FROM STEP 2

ASSEMBLY FRAME

FROM STEP 1

8For Customer Service Call 1-888-996-2729

STEP 4

PARTS REQUIRED:

2 pcs - H2 M6 x 90 mm

Allen

Head Bolt 2 pcs -H6 Plastic Bushing

2 pcs - H4 Flat Washer 1 pc - P5 Front Tube Assembly

2 pcs - H5 Wing Nut 2 pcs - P15 Locking Pin

Connect P5 Front Tube Assembly using Spring Lock

as shown in FIGURE 4.

NOTE: Bungee Cord is an assembly aide and stays in place.

FIGURE 4

Spring Lock

Bungee

Cord

Spring Lock

Bungee

Cord

STEP 5

Connect P5 Front Tube Assembly to P1 - Left Lower Tube Assembly

and P2 - Right Lower Tube Assembly using H2 Bolts, H4 Washers,

H6 Bushing and H5 Wing Nuts as shown in FIGURE 5 and DETAIL B.

Note: This is a pivot point. “Snug” tighten H5 Wing Nuts only.

Make sure this assembly pivots freely.

H4 H5

P15

FIGURE 5

DETAIL B

NOTE: Use “bottom” hole

for this assembly.

NOTE: Push H2 Bolts

around the inner bungee

cord.

9For Customer Service Call 1-888-996-2729

STEP 6

PARTS REQUIRED:

16 pcs -

H3 M6 x 25 mm Allen Head Bolt 1 pc - P7 Backboard

H5 Wing Nut 2 pcs - P11 Mechanical Scoring Arm

H7 Lock Washer 2 pcs - P12 Rim

1 pc - T1

Allen Wrench 2 pcs -

2 pcs -P18 Mechanical Scoring Arm Support Plate

P14 Rim Support Plate

Attach

Attach P11 Mechanical Scoring Arms and P18

Mechanical Scoring Arm Support Plates to the

P7 Backboard using H3 Bolts, H7 Lock washers

and H5 Wing nuts as shown in FIGURE 6.

P12 Rim and P14 Rim Support Plate

to the P7 Backboard using H3 Bolts, H7 Lock

Washers and H5 Wing Nuts as shown

in FIGURE 6.

Use T1 Allen Wrench and Plyers

(not provided) to tighten all Bolts.

FIGURE 7

P9 P7

PARTS REQUIRED:

1 pc - P9 Electronic Scorer

1 pc - P10 Electronic Scorer Face Plate

2 pcs - P13 Rim Net

STEP 7

Attach P9 Electronic Scorer and P10 Electronic

Scorer Face Plate to P7 Backboard as shown

in FIGURE 7.

NOTE: Place P10 Electronic Scorer Face Plate

into P7 Backboard first, then carefully “press”

P9 Electronic Scorer onto the four tabs on P10.

You should hear the four tabs “snap”

into place.

Loop the P13 Rim Net through the ram horns

on the P12 Rims as shown in FIGURE 7.

P13

P10

NOTE:

Remove Protective

Coating before

assembly.

P11

P18

P14

P12

H5 H7

FIGURE 6

NOTE:

P11 Mechanical Scoring

Arm

sensor plug must pass through

P7 Backboard and P18 Mechanical

Scoring Arm Support Plate.

Note: This is a special rim net

designed to avoid entanglement

with the mechanical scoring arm.`

Net does have a

top and bottom,

The long loops go

to the top.

2019

10 For Customer Service Call 1-888-996-2729

STEP 8

PARTS REQUIRED:

2 pcs - P6 Upper Tube

Attach Backboard assembly from STEP 7 to Frame assembly from STEP 5 as shown in FIGURE 8.

Attach P6 Upper Tubes to P7 Backboard assembly using Spring Lock as shown in FIGURE 8.

FIGURE 8

Spring Lock

NOTE :

IF BACKBOARD TUBES DO NOT

WANT TO ATTACH TO THE FRAME

ASSEMBLY -- SIMPLY LOOSEN THE

4 BOLTS AND NUTS AT THE ENDS

OF THE HORIZONTAL TUBES IN

THE BACKSIDE OF THE LOWER

FRAME TO CORRECTLY ADJUST

THE CONNECTING TUBES .

RETIGHTEN THE 4 BOLTS AND

NUTS WHEN BACKBOARD

ASSEMBLY IS CORRECTLY

ATTACHED .

Spring Lock

2019

Inhaltsverzeichnis

Andere Triumph Sport & Outdoor Handbücher

Triumph

Triumph 45-6807 Bedienungsanleitung

Triumph

Triumph 35-7094 Bedienungsanleitung

Triumph

Triumph 35-7415 Bedienungsanleitung

Triumph

Triumph 35-7306 Bedienungsanleitung

Triumph

Triumph 45-6099BLU Bedienungsanleitung

Triumph

Triumph 35-7020-3 Bedienungsanleitung

Triumph

Triumph 45-6730MT Bedienungsanleitung

Triumph

Triumph 4square Bedienungsanleitung

Triumph

Triumph 35-7500-2 Bedienungsanleitung

Triumph

Triumph 35-7390-2 Bedienungsanleitung

Triumph

Triumph MULTI-SPORT COMBO Bedienungsanleitung

Triumph

Triumph 45-6851W/F Bedienungsanleitung

Triumph

Triumph COMPETITION BADMINTON SET Bedienungsanleitung

Triumph

Triumph 35-7450-3 Bedienungsanleitung

Triumph

Triumph 35-7105-2 Bedienungsanleitung

Triumph

Triumph 45-6103FAW Bedienungsanleitung

Triumph

Triumph HORSESHOES Bedienungsanleitung

Beliebte Sport & Outdoor Handbücher anderer Marken

Flybar

Flybar POGO TRICK BOARD Bedienungsanleitung

Crivit

Crivit 93713 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90865 Bedienungsanleitung

Hudora

Hudora 76171 Montageanleitung

Axler

Axler GSU-1 Bedienungsanleitung

Aquaglide

Aquaglide FREEFALL 6 LANDING PAD Bedienungsanleitung

Cap Strength

Cap Strength POWER RACK FM-CS7000F Bedienungsanleitung

La Sportiva

La Sportiva RACE BORG Bedienungsanleitung

Crivit

Crivit 302640 Bedienungsanleitung

Sportime

Sportime Equalizer Bedienungsanleitung

T&R Sports

T&R Sports 5FT FOOSBALL TABLE Bedienungsanleitung

Salewa

Salewa VERT Bedienungsanleitung

KICK

KICK Decagon Bedienungsanleitung

byox

byox FJ-4.5FT Bedienungsanleitung

CHINESPORT Spa

CHINESPORT Spa 01325 Bedienungsanleitung

AXI.COM

AXI.COM ConesPro101 Bedienungsanleitung

Insportline

Insportline IN 2052 Bedienungsanleitung

Rugged Interactive

Rugged Interactive CardioWall Compact Kurzanleitung