Troy Built Models ME - 109 Bedienungsanleitung

Specification:

ME - 109

Length :1600 mm(63")

Wing Span :1841 mm(72.5")

Wing Area :55.0 sq. dm

5.92 sq. ft

Wing Loading :85.8 g/sq. dm

35.1 oz/sq. ft

Flying Weight :5.9 kg(13 lbs)

Radio :6ch&8 servos

Engine :108 2-cycle

120 4-cycle

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building

experience.If misused or abused,it can cause serious bodily injury

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your

airplane before its first flight.Please carefully read and follow all

instructions included with this airplane,your radio control system

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not a toy!

4-cycle .120

15″X8

107mm Spinner

6 channel radio for aiplane is highly recommended for this model.

Choose servos with large torque to

achieve great performanoe.

Warning

Remove the covering with proper

pressure to cut through only the covering itself.Otherwise,

cutting down into the balsa structure may weaken the model part

and cause accident.

The pre-covered film on ARF kits may wrinkle due to variations of

temperature.Smooth out as explained right.

Rod (2x300mm)

Retainer

Wooden Block

Servo tray

1.5mm

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

Clevis

Rod (2x300mm)

Retainer

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Pin hinge(24x24mm)

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

Clevis

Retainer

Rod (2x300mm)

Screw (2x10mm)

Aileron.Apply instant type CA glue to both

sides of each hinge.

Install the servo.

Install the nylon control horn and

connect the linkage.

Epoxy the servo supporter and install the servo.

Remove the film carefully for mounting

the aileron servo tray.

Accessory list for this page.

Air tank

Switch

Air inlet

3-way

pressure inlet

3-way

pressure inlet

3-way

pressure inlet

The status when the

gear up

Pull out length of 8mm

to make gear down

Air valve Air valve

Make sure to assemble retracts as instructed below.

Two wheel retract system

Quick release connector

Pressure reduction inlet

Strut

3-way pressure inlet 3

Pressure reduction inlet 1

Air tank

Air inlet

Air line (3000mm)

Quick release connector

Strut

( 90 )

Switch

Clevis

Rod (2X300mm)

Retainer

TP Screw(2x14mm) 2

Ø1.7mm

Ø0.2mm

Pleas notice the inner diameter

of eachside the pressure reduction inlet.

Please insure the sealing of theretract

system before flight .

Rod (2x300mm)

Retainer

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

1.5mm

3mm

TP Screw (2.3x12mm)

1.5mm

Wooden Block

Servo tray

Clevis

Rod (2x300mm)

Retainer

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Pin hinge(24x24mm)

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

Clevis

Retainer

Rod (2x300mm)

Screw (2x10mm)

Rod (2x300mm)

Clevis

Washer(3x15mm)

Washer

Lock Nut (3mm )

Screw (3x35mm)

TP Screw (2.3x12mm)

Connect the linkage rod to the horn.

Install the servo.

Secure the servo. Install the nylon control

horn and connect the linkage. Mount servo on the ply plate.

Flap. Apply instant type CA glue to both sides

of each hinge.

Accessory list for this page.

Piease refer to installation diagram for details.

TP Screw (2.3x12mm)

1.5mm

5mm

Clevis

Rod (2x300mm)

Retainer

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Pin hinge(24x24mm)

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

Rod (2x300mm)

Clevis

Washer(3x15mm)

Washer

Lock Nut (3mm )

Screw (3x35mm)

TP Screw (2.3x12mm)

3mm

Cut away the surplus parts of plastic cover

carefully along the shaded line.

Remove the film on the position for the air

retract landing gear.

Optional air retract package.

(Should be purchased separately)

Secure the flap servo. Install the nylon control

horn and connect the linkage.

Remove the film carefully for mounting

the flap servo tray.

Accessory list for this page.

116mm

Top view

Position for

right diagram.

ELEVATOR

Side View

25mm

20mm

RUDDER

Adjustment.

Centre of Gravity.

6766

Landing gear

TP Screw (2.6x14mm)

Retracts strut

TP Screw (3x20mm)

Retracts strut

Landing gear

1.5mm

Wheel baffle

Wheel well

Air line(600mm)

Wheel well

Retracts strut

LockNut(4mm)

Wooden Block

Gear door

Wheel (100mm)

Screw (3x10mm)

Mounting

Note:rubber wheels oleo struts

and retracts are optional.

LockNut(4mm)

Mount the baffle on the landing gear. Mount the baffle on the landing gear.

Epoxy the wheel well. Assemble landing gear.

Assemble are retracts.

Accessory list for this page.

TP Screw (3x20mm)

Washer (3x6mm) 4

1.5mm

60mm

120mm

1.5mm

TP Screw (2.3x8mm)

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

TP Screw (2.3x8mm)

Canopy

PVC part

Tail strut

4mm

20mm

30mm

AILERON

FLAP

AILERON

Side View

TP Screw (3x20mm)

Washer (3x6mm) 4

Tail strut

Mount here firstly

Fix the canopy with self - tapping screws.

Cut away the surplus parts of plastic cover

carefully along the shaded line. Assemble the strut of stabilizer.

Adjustment.

Epoxy the heat-sink cover to the

main wing and flap steadily.

Accessory list for this page.

1.5mm

TP Screw(2.3x8mm)

Metal bush(35x4mm)

Throttle servo

Elevator servo

Retracts servo

Rudder servo

Air inlet

Air tank

Switch

1.5mm

6mm

Screw (2x25mm)

Nut (2mm)

Aluminum Washer (2mm)

Ply plate (3mm)

Linkage Stopper 4

Matal bush

Ply plate (3mm)

Clevis

Rod (2X300mm)

1Retainer

Ring

Screw (2x25mm)

Nut (2mm )

Air inlet

Air tank

Switch

Aluminum Washer (2mm )

Aluminum Washer (6mm)

Air line (800mm)

TP Screw (2.3x8mm)

Linkage Stopper 4

Metal bush(35x4mm)

Attach bush to engine shaft when assembling

optiinal spinner.

Trim the cowling for engine and muffler.

Mounting of the receiver and the battery.

Assemble the servos and switch in the fuselage.

Position ply plates inside fuselage steadily.

Accessory list for this page.

3-way

pressure inlet

3-way pressure inlet 1

Center line

150mm

100mm

20mm

Main wing joiner

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

Blind Nut (6mm)

Screw (6x50mm)

A=A'

Drill 6.2mm holes at the place

of main wing.

Install the wing to the fuselage

with 6x50mm screws as shown

in the diagrams below.

Collar {5mm) 2

Collar (5mm)

Wheel (100mm)

B`B

Center

line

3-way pressure inlet 1

Quick release connector

Quick release

connector

Quick release connector

Connect air lines with pressure inlet.

Cut out the hole for exit of servo leads.

Epoxy two main wing panels together.

Install the main wing.

Install main wheels.

Accessory list for this page.

Reinforcement Plate 1

6.2mm

Blind Nut

Blind Nut (6mm)

Screw(6x50mm)

Blind Nut (6mm)

Screw (6x40mm)

Wood dowel (6x50mm)

6mm

Wood dowel (6x50mm)

40mm 40mm

6mm

Reinforcement Plate 1

Epoxy the reinforcement plate securely to

the main wing.

Remove the film carefully on the position for

the reinforcement plate.

Mount the main wing on the fuselage.

Drill holes in the fuselage to install the main wing.

Epoxy the dowel on the wing.

Accessory list for this page.

Fuel tank (550ml) 1

TP Screw (2.3x8mm) 5

Engine mount (68x105 mm)

Linkage Stopper

Washer(4x8mm)

Screw (4x35mm)

Spring Washer (4mm)

Nut (4mm)

Screw (4x25mm)

Plastic tube (2x350mm)

Fuel tank (550ml) 1

Linkage Stopper

Washer (2mm)

Nut (2mm)

Set screw (3x4mm)

Washer (

2mm

)

Set screw (3x4mm)

Fuel supply line

Fuel pipe

Air pressure line

Clevis

Rod (2X300mm)

Retainer

Ring

Mount the fuel tank into the fuselage.

Install the engine.

Install the nylon control ring for switch and

connect the linkage.

Assembly of the fuel tank.

Assemble the servos and switch in the fuselage.

Accessory list for this page.

4mm Blind Nut

Blind nut (4mm) 4

148mm

In case of 2-cycle engine. In case of 4-cycle engine.

2.5mm

Set Screw (3x4mm)

Set Screw (2mm)

Rod (2x350mm)

Set Screw (2mm)

Washer (2mm)

Linkage Stopper

Washer (4x8mm)

Rod (2x350mm)

Blind Nut (4mm)

Screw (4x25mm)

Set Screw (3x4mm)

Washer (4x8mm)

Spring Washer

(

4mm)

Nut

(

4mm)

4mm

Screw (4x35mm)

Nut (4mm)

Spring Washer (4mm)

5.2mm

Blind Nut

Assemble the engine.

Drill four holes at the diameters as shown

for engine mount.

Assemble the engine.

Assemble the engine. Assemble the engine.

Accessory list for this page.

Pin hinge(24x24mm)

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

Make sure hinges are

mounted in the same line.

Rib template (3mm ply)

Wood dowel (4x30mm)

4mm

Epoxy the stabilizers to the fuselage as below.

Stab joiner (12x220mm)

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Wood dowel (4x30mm)

Rib template (3mm ply)

Pin hinge(24x24mm)

AA'

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming off during flights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

Install horizontal tail and elevator separately.

Apply instant type CA glue to elevator and pin hinge.

According to the rib template drill holes to appropriate

position in the fuselage and stabilizers.

Assembly of the stabilizer.

Accessory list for this page.

3mm

Pin hinge

Securely glue together. If coming off during flighs, you 'll

lose control of your airplane which leads to accidents!

35mm

55mm

Pin hinge(2.5x48mm)

Nose arm(3mm)

Collar (3mm) 1

Tail landing gear(3mm)

Tail wheel (45mm)

Retainer

TP Screw(3x20mm)

Washer (3x6mm)

1.8mm

suggest drilling a hole here for

assembling wheel steeling

mount

20mm

TP Screw(3x20mm)

Washer (3x6mm)

3mm

30mm

60mm

55mm

Vertical tail

Metal arm

Collar

Tail landing gear

Metal arm

Nose arm

20o

The sketch map of assembling the wheel steeling

mount to appropriate position in the fuselage.

The sketch map when tail wheel assemble completion. Drill a hole to appropriate position in the

rudder and vertical fin as illustration.

Epoxy rudder steadily in position.

2x200mm Rod

2x300mm Rod

Clevis

2x200mm Rod

8x800mm Rod

230mm

Assemble the linkage rods for elevator and rudder.

Accessory list for this page.

Rod (2x300mm) 1

Rod (2x300mm)

Clevis

Washer(3x15mm)

Washer

Lock Nut (3mm )

Screw (3x35mm)

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Collar

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Clevis

Retainer

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

Screw (3x80mm)

Rod (2x300mm)

Lock Nut (3mm )

Washer(3x15mm) Screw (3x65mm)

Rudder servo

110mm

16mm

Elevator tail

25mm

3mm

65mm

Tail wheel tail

Rod (2x300mm)

Lock Nut (3mm )

Washer(3x15mm) Screw (3x65mm)

Tail wheel

Rudder servo

Retainer

Elevator.Connect the linkage rod to the horn.

Connect the rudder servo to the rudder horn.

Epoxy ply to appropriate position in the fuselage

and assemble the tail gear cover with screw.

Drill a hole to appropriate position in the

vertical fin as illustration.

Drill a hole in the tail fuselage and connect the rudder

horn to the tail wheel as illustration.

Accessory list for this page.

Andere Troy Built Models Spielzeug Handbücher

Troy Built Models

Troy Built Models DC-3 Bedienungsanleitung

Troy Built Models

Troy Built Models P-47D Thunderbolt Bedienungsanleitung

Troy Built Models

Troy Built Models 105” Curtiss JN-4 Bedienungsanleitung

Troy Built Models

Troy Built Models Aichi D3A1 Bedienungsanleitung

Troy Built Models

Troy Built Models BF-110C ZERSTORER Bedienungsanleitung

Troy Built Models

Troy Built Models P-40 warhawk Bedienungsanleitung

Troy Built Models

Troy Built Models SHOCKJET MF 6 Bedienungsanleitung

Troy Built Models

Troy Built Models Bonanza V-35 Bedienungsanleitung

Troy Built Models

Troy Built Models Electric Beaver Bedienungsanleitung

Troy Built Models

Troy Built Models F86D DOG SABRE Bedienungsanleitung

Troy Built Models

Troy Built Models T-28 Trojah Bedienungsanleitung

Troy Built Models

Troy Built Models Memphis Belle B-17 Bedienungsanleitung

Troy Built Models

Troy Built Models FAIREY SWORDFLSH Bedienungsanleitung

Troy Built Models

Troy Built Models B-25 Mitchell Bedienungsanleitung

Troy Built Models

Troy Built Models Hawker hurricane MK.IIa Bedienungsanleitung

Troy Built Models

Troy Built Models Ki84 Hayate Bedienungsanleitung

Troy Built Models

Troy Built Models SPITFIRE MK.XIV Bedienungsanleitung

Troy Built Models

Troy Built Models F-4u Corsair Bedienungsanleitung

Troy Built Models

Troy Built Models ROBIN DR400 Bedienungsanleitung

Troy Built Models

Troy Built Models Do-335 Bedienungsanleitung

Troy Built Models

Troy Built Models P-39 Airacobra Bedienungsanleitung

Troy Built Models

Troy Built Models 50cc SPITFIRE Bedienungsanleitung

Troy Built Models

Troy Built Models P-51B Mustang Bedienungsanleitung

Troy Built Models

Troy Built Models Hawker Typhoon Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung